uboot/u-boot-stm32mp-2020.01/board/toradex/apalis-tk1/as3722_init.c

140 lines
4.6 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (c) 2012-2016 Toradex, Inc.
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch-tegra/tegra_i2c.h>
#include "as3722_init.h"
/* AS3722-PMIC-specific early init code - get CPU rails up, etc */
void tegra_i2c_ll_write_addr(uint addr, uint config)
{
struct i2c_ctlr *reg = (struct i2c_ctlr *)TEGRA_DVC_BASE;
writel(addr, &reg->cmd_addr0);
writel(config, &reg->cnfg);
}
void tegra_i2c_ll_write_data(uint data, uint config)
{
struct i2c_ctlr *reg = (struct i2c_ctlr *)TEGRA_DVC_BASE;
writel(data, &reg->cmd_data1);
writel(config, &reg->cnfg);
}
void pmic_enable_cpu_vdd(void)
{
debug("%s entry\n", __func__);
#ifdef AS3722_SD1VOLTAGE_DATA
/* Set up VDD_CORE, for boards where OTP is incorrect*/
debug("%s: Setting VDD_CORE via AS3722 reg 1\n", __func__);
/* Configure VDD_CORE via the AS3722 PMIC on the PWR I2C bus */
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(AS3722_SD1VOLTAGE_DATA, I2C_SEND_2_BYTES);
/*
* Don't write SDCONTROL - it's already 0x7F, i.e. all SDs enabled.
* tegra_i2c_ll_write_data(AS3722_SD1CONTROL_DATA, I2C_SEND_2_BYTES);
*/
udelay(10 * 1000);
#endif
/*
* Make sure all non-fused regulators are down.
* That way we're in known state after software reboot from linux
*/
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(0x0003, I2C_SEND_2_BYTES);
udelay(10 * 1000);
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(0x0004, I2C_SEND_2_BYTES);
udelay(10 * 1000);
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(0x001b, I2C_SEND_2_BYTES);
udelay(10 * 1000);
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(0x0014, I2C_SEND_2_BYTES);
udelay(10 * 1000);
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(0x001a, I2C_SEND_2_BYTES);
udelay(10 * 1000);
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(0x0019, I2C_SEND_2_BYTES);
udelay(10 * 1000);
debug("%s: Setting VDD_CPU to 1.0V via AS3722 reg 0/4D\n", __func__);
/*
* Bring up VDD_CPU via the AS3722 PMIC on the PWR I2C bus.
* First set VDD to 1.0V, then enable the VDD regulator.
*/
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(AS3722_SD0VOLTAGE_DATA, I2C_SEND_2_BYTES);
/*
* Don't write SDCONTROL - it's already 0x7F, i.e. all SDs enabled.
* tegra_i2c_ll_write_data(AS3722_SD0CONTROL_DATA, I2C_SEND_2_BYTES);
*/
udelay(10 * 1000);
debug("%s: Setting VDD_GPU to 1.0V via AS3722 reg 6/4D\n", __func__);
/*
* Bring up VDD_GPU via the AS3722 PMIC on the PWR I2C bus.
* First set VDD to 1.0V, then enable the VDD regulator.
*/
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(AS3722_SD6VOLTAGE_DATA, I2C_SEND_2_BYTES);
/*
* Don't write SDCONTROL - it's already 0x7F, i.e. all SDs enabled.
* tegra_i2c_ll_write_data(AS3722_SD6CONTROL_DATA, I2C_SEND_2_BYTES);
*/
udelay(10 * 1000);
debug("%s: Set VPP_FUSE to 1.2V via AS3722 reg 0x12/4E\n", __func__);
/*
* Bring up VPP_FUSE via the AS3722 PMIC on the PWR I2C bus.
* First set VDD to 1.2V, then enable the VDD regulator.
*/
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(AS3722_LDO2VOLTAGE_DATA, I2C_SEND_2_BYTES);
/*
* Don't write LDCONTROL - it's already 0xFF, i.e. all LDOs enabled.
* tegra_i2c_ll_write_data(AS3722_LDO2CONTROL_DATA, I2C_SEND_2_BYTES);
*/
udelay(10 * 1000);
debug("%s: Set VDD_SDMMC1 to 3.3V via AS3722 reg 0x11/4E\n", __func__);
/*
* Bring up VDD_SDMMC1 via the AS3722 PMIC on the PWR I2C bus.
* First set it to value closest to 3.3V, then enable the regulator
*
* NOTE: We do this early because doing it later seems to hose the CPU
* power rail/partition startup. Need to debug.
*/
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(AS3722_LDO1VOLTAGE_DATA, I2C_SEND_2_BYTES);
/*
* Don't write LDCONTROL - it's already 0xFF, i.e. all LDOs enabled.
* tegra_i2c_ll_write_data(AS3722_LDO1CONTROL_DATA, I2C_SEND_2_BYTES);
*/
udelay(10 * 1000);
debug("%s: Set VDD_SDMMC3 to 3.3V via AS3722 reg 0x16/4E\n", __func__);
/*
* Bring up VDD_SDMMC3 via the AS3722 PMIC on the PWR I2C bus.
* First set it to bypass 3.3V straight thru, then enable the regulator
*
* NOTE: We do this early because doing it later seems to hose the CPU
* power rail/partition startup. Need to debug.
*/
tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
tegra_i2c_ll_write_data(AS3722_LDO6VOLTAGE_DATA, I2C_SEND_2_BYTES);
/*
* Don't write LDCONTROL - it's already 0xFF, i.e. all LDOs enabled.
* tegra_i2c_ll_write_data(AS3722_LDO6CONTROL_DATA, I2C_SEND_2_BYTES);
*/
udelay(10 * 1000);
}