uboot/u-boot-stm32mp-2020.01/board/tbs/tbs2910/tbs2910.c

181 lines
4.6 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2014 Soeren Moch <smoch@web.de>
*/
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/video.h>
#include <mmc.h>
#include <fsl_esdhc_imx.h>
#include <asm/arch/mxc_hdmi.h>
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
static iomux_v3_cfg_t const uart1_pads[] = {
MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const uart2_pads[] = {
MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
};
int dram_init(void)
{
gd->ram_size = 2048ul * 1024 * 1024;
return 0;
}
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
}
#ifdef CONFIG_FSL_ESDHC_IMX
/* set environment device to boot device when booting from SD */
int board_mmc_get_env_dev(int devno)
{
return devno - 1;
}
int board_mmc_get_env_part(int devno)
{
return (devno == 3) ? 1 : 0; /* part 0 for SD2 / SD3, part 1 for eMMC */
}
#endif /* CONFIG_FSL_ESDHC_IMX */
#ifdef CONFIG_VIDEO_IPUV3
static void do_enable_hdmi(struct display_info_t const *dev)
{
imx_enable_hdmi_phy();
}
struct display_info_t const displays[] = {{
.bus = -1,
.addr = 0,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = detect_hdmi,
.enable = do_enable_hdmi,
.mode = {
.name = "HDMI",
/* 1024x768@60Hz (VESA)*/
.refresh = 60,
.xres = 1024,
.yres = 768,
.pixclock = 15384,
.left_margin = 160,
.right_margin = 24,
.upper_margin = 29,
.lower_margin = 3,
.hsync_len = 136,
.vsync_len = 6,
.sync = FB_SYNC_EXT,
.vmode = FB_VMODE_NONINTERLACED
} } };
size_t display_count = ARRAY_SIZE(displays);
static void setup_display(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
int reg;
s32 timeout = 100000;
enable_ipu_clock();
imx_setup_hdmi();
/* set video pll to 455MHz (24MHz * (37+11/12) / 2) */
reg = readl(&ccm->analog_pll_video);
reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN;
writel(reg, &ccm->analog_pll_video);
reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(37);
reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1);
writel(reg, &ccm->analog_pll_video);
writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
writel(reg, &ccm->analog_pll_video);
while (timeout--)
if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
break;
if (timeout < 0)
printf("Warning: video pll lock timeout!\n");
reg = readl(&ccm->analog_pll_video);
reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
writel(reg, &ccm->analog_pll_video);
/* gate ipu1_di0_clk */
reg = readl(&ccm->CCGR3);
reg &= ~MXC_CCM_CCGR3_LDB_DI0_MASK;
writel(reg, &ccm->CCGR3);
/* select video_pll clock / 7 for ipu1_di0_clk -> 65MHz pixclock */
reg = readl(&ccm->chsccdr);
reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK |
MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK |
MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET) |
(6 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) |
(0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
writel(reg, &ccm->chsccdr);
/* enable ipu1_di0_clk */
reg = readl(&ccm->CCGR3);
reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
writel(reg, &ccm->CCGR3);
}
#endif /* CONFIG_VIDEO_IPUV3 */
int board_early_init_f(void)
{
setup_iomux_uart();
return 0;
}
#ifdef CONFIG_CMD_BMODE
static const struct boot_mode board_boot_modes[] = {
/* 4 bit bus width */
{"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
{"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
/* 8 bit bus width */
{"emmc", MAKE_CFGVAL(0x60, 0x58, 0x00, 0x00)},
{NULL, 0},
};
#endif
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_VIDEO_IPUV3
setup_display();
#endif
#ifdef CONFIG_CMD_BMODE
add_board_boot_modes(board_boot_modes);
#endif
return 0;
}