860 lines
22 KiB
C
860 lines
22 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
|
*
|
|
* Author: Fabio Estevam <fabio.estevam@freescale.com>
|
|
*
|
|
* Copyright (C) 2013 Jon Nettleton <jon.nettleton@gmail.com>
|
|
*
|
|
* Based on SPL code from Solidrun tree, which is:
|
|
* Author: Tungyi Lin <tungyilin1127@gmail.com>
|
|
*
|
|
* Derived from EDM_CF_IMX6 code by TechNexion,Inc
|
|
* Ported to SolidRun microSOM by Rabeeh Khoury <rabeeh@solid-run.com>
|
|
*/
|
|
|
|
#include <init.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/iomux.h>
|
|
#include <asm/arch/mx6-pins.h>
|
|
#include <asm/arch/mxc_hdmi.h>
|
|
#include <env.h>
|
|
#include <linux/errno.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/mach-imx/sata.h>
|
|
#include <asm/mach-imx/video.h>
|
|
#include <mmc.h>
|
|
#include <fsl_esdhc_imx.h>
|
|
#include <malloc.h>
|
|
#include <miiphy.h>
|
|
#include <netdev.h>
|
|
#include <asm/arch/crm_regs.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <spl.h>
|
|
#include <usb.h>
|
|
#include <usb/ehci-ci.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
|
|
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
|
|
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
|
|
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL_PD (PAD_CTL_PUS_100K_DOWN | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL_CLK ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
|
|
|
|
#define ETH_PHY_RESET IMX_GPIO_NR(4, 15)
|
|
#define USB_H1_VBUS IMX_GPIO_NR(1, 0)
|
|
|
|
enum board_type {
|
|
CUBOXI = 0x00,
|
|
HUMMINGBOARD = 0x01,
|
|
HUMMINGBOARD2 = 0x02,
|
|
UNKNOWN = 0x03,
|
|
};
|
|
|
|
#define MEM_STRIDE 0x4000000
|
|
static u32 get_ram_size_stride_test(u32 *base, u32 maxsize)
|
|
{
|
|
volatile u32 *addr;
|
|
u32 save[64];
|
|
u32 cnt;
|
|
u32 size;
|
|
int i = 0;
|
|
|
|
/* First save the data */
|
|
for (cnt = 0; cnt < maxsize; cnt += MEM_STRIDE) {
|
|
addr = (volatile u32 *)((u32)base + cnt); /* pointer arith! */
|
|
sync ();
|
|
save[i++] = *addr;
|
|
sync ();
|
|
}
|
|
|
|
/* First write a signature */
|
|
* (volatile u32 *)base = 0x12345678;
|
|
for (size = MEM_STRIDE; size < maxsize; size += MEM_STRIDE) {
|
|
* (volatile u32 *)((u32)base + size) = size;
|
|
sync ();
|
|
if (* (volatile u32 *)((u32)base) == size) { /* We reached the overlapping address */
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* Restore the data */
|
|
for (cnt = (maxsize - MEM_STRIDE); i > 0; cnt -= MEM_STRIDE) {
|
|
addr = (volatile u32 *)((u32)base + cnt); /* pointer arith! */
|
|
sync ();
|
|
*addr = save[i--];
|
|
sync ();
|
|
}
|
|
|
|
return (size);
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
u32 max_size = imx_ddr_size();
|
|
|
|
gd->ram_size = get_ram_size_stride_test((u32 *) CONFIG_SYS_SDRAM_BASE,
|
|
(u32)max_size);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static iomux_v3_cfg_t const uart1_pads[] = {
|
|
IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const usdhc2_pads[] = {
|
|
IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const usdhc3_pads[] = {
|
|
IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const board_detect[] = {
|
|
/* These pins are for sensing if it is a CuBox-i or a HummingBoard */
|
|
IOMUX_PADS(PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(UART_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_EIM_DA4__GPIO3_IO04 | MUX_PAD_CTRL(UART_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(UART_PAD_CTRL)),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const som_rev_detect[] = {
|
|
/* These pins are for sensing if it is a CuBox-i or a HummingBoard */
|
|
IOMUX_PADS(PAD_CSI0_DAT14__GPIO6_IO00 | MUX_PAD_CTRL(UART_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_CSI0_DAT18__GPIO6_IO04 | MUX_PAD_CTRL(UART_PAD_CTRL)),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const usb_pads[] = {
|
|
IOMUX_PADS(PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL)),
|
|
};
|
|
|
|
static void setup_iomux_uart(void)
|
|
{
|
|
SETUP_IOMUX_PADS(uart1_pads);
|
|
}
|
|
|
|
static struct fsl_esdhc_cfg usdhc_cfg = {
|
|
.esdhc_base = USDHC2_BASE_ADDR,
|
|
.max_bus_width = 4,
|
|
};
|
|
|
|
static struct fsl_esdhc_cfg emmc_cfg = {
|
|
.esdhc_base = USDHC3_BASE_ADDR,
|
|
.max_bus_width = 8,
|
|
};
|
|
|
|
int board_mmc_get_env_dev(int devno)
|
|
{
|
|
return devno - 1;
|
|
}
|
|
|
|
#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
|
|
|
|
int board_mmc_getcd(struct mmc *mmc)
|
|
{
|
|
struct fsl_esdhc_cfg *cfg = mmc->priv;
|
|
int ret = 0;
|
|
|
|
switch (cfg->esdhc_base) {
|
|
case USDHC2_BASE_ADDR:
|
|
ret = !gpio_get_value(USDHC2_CD_GPIO);
|
|
break;
|
|
case USDHC3_BASE_ADDR:
|
|
ret = (mmc_get_op_cond(mmc) < 0) ? 0 : 1; /* eMMC/uSDHC3 has no CD GPIO */
|
|
break;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int mmc_init_main(bd_t *bis)
|
|
{
|
|
int ret;
|
|
|
|
/*
|
|
* Following map is done:
|
|
* (U-Boot device node) (Physical Port)
|
|
* mmc0 Carrier board MicroSD
|
|
* mmc1 SOM eMMC
|
|
*/
|
|
SETUP_IOMUX_PADS(usdhc2_pads);
|
|
usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
|
|
ret = fsl_esdhc_initialize(bis, &usdhc_cfg);
|
|
if (ret)
|
|
return ret;
|
|
|
|
SETUP_IOMUX_PADS(usdhc3_pads);
|
|
emmc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
|
|
return fsl_esdhc_initialize(bis, &emmc_cfg);
|
|
}
|
|
|
|
static int mmc_init_spl(bd_t *bis)
|
|
{
|
|
struct src *psrc = (struct src *)SRC_BASE_ADDR;
|
|
unsigned reg = readl(&psrc->sbmr1) >> 11;
|
|
|
|
/*
|
|
* Upon reading BOOT_CFG register the following map is done:
|
|
* Bit 11 and 12 of BOOT_CFG register can determine the current
|
|
* mmc port
|
|
* 0x1 SD2
|
|
* 0x2 SD3
|
|
*/
|
|
switch (reg & 0x3) {
|
|
case 0x1:
|
|
SETUP_IOMUX_PADS(usdhc2_pads);
|
|
usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
|
|
gd->arch.sdhc_clk = usdhc_cfg.sdhc_clk;
|
|
return fsl_esdhc_initialize(bis, &usdhc_cfg);
|
|
case 0x2:
|
|
SETUP_IOMUX_PADS(usdhc3_pads);
|
|
emmc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
|
|
gd->arch.sdhc_clk = emmc_cfg.sdhc_clk;
|
|
return fsl_esdhc_initialize(bis, &emmc_cfg);
|
|
}
|
|
|
|
return -ENODEV;
|
|
}
|
|
|
|
int board_mmc_init(bd_t *bis)
|
|
{
|
|
if (IS_ENABLED(CONFIG_SPL_BUILD))
|
|
return mmc_init_spl(bis);
|
|
|
|
return mmc_init_main(bis);
|
|
}
|
|
|
|
static iomux_v3_cfg_t const enet_pads[] = {
|
|
IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
|
|
/* AR8035 reset */
|
|
IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
|
|
/* AR8035 interrupt */
|
|
IOMUX_PADS(PAD_DI0_PIN2__GPIO4_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL)),
|
|
/* GPIO16 -> AR8035 25MHz */
|
|
IOMUX_PADS(PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(NO_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(NO_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)),
|
|
/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
|
|
IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK)),
|
|
IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
|
|
IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
|
|
IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
|
|
IOMUX_PADS(PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
|
|
IOMUX_PADS(PAD_ENET_RXD1__GPIO1_IO26 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
|
|
};
|
|
|
|
static void setup_iomux_enet(void)
|
|
{
|
|
SETUP_IOMUX_PADS(enet_pads);
|
|
|
|
gpio_direction_output(ETH_PHY_RESET, 0);
|
|
mdelay(10);
|
|
gpio_set_value(ETH_PHY_RESET, 1);
|
|
udelay(100);
|
|
}
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* On Cuboxi Ethernet PHY can be located at addresses 0x0 or 0x4 */
|
|
#define ETH_PHY_MASK ((1 << 0x0) | (1 << 0x4))
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
|
|
struct mii_dev *bus;
|
|
struct phy_device *phydev;
|
|
|
|
int ret = enable_fec_anatop_clock(0, ENET_25MHZ);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* set gpr1[ENET_CLK_SEL] */
|
|
setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
|
|
|
|
setup_iomux_enet();
|
|
|
|
bus = fec_get_miibus(IMX_FEC_BASE, -1);
|
|
if (!bus)
|
|
return -EINVAL;
|
|
|
|
phydev = phy_find_by_mask(bus, ETH_PHY_MASK, PHY_INTERFACE_MODE_RGMII);
|
|
if (!phydev) {
|
|
ret = -EINVAL;
|
|
goto free_bus;
|
|
}
|
|
|
|
debug("using phy at address %d\n", phydev->addr);
|
|
ret = fec_probe(bis, -1, IMX_FEC_BASE, bus, phydev);
|
|
if (ret)
|
|
goto free_phydev;
|
|
|
|
return 0;
|
|
|
|
free_phydev:
|
|
free(phydev);
|
|
free_bus:
|
|
free(bus);
|
|
return ret;
|
|
}
|
|
|
|
#ifdef CONFIG_VIDEO_IPUV3
|
|
static void do_enable_hdmi(struct display_info_t const *dev)
|
|
{
|
|
imx_enable_hdmi_phy();
|
|
}
|
|
|
|
struct display_info_t const displays[] = {
|
|
{
|
|
.bus = -1,
|
|
.addr = 0,
|
|
.pixfmt = IPU_PIX_FMT_RGB24,
|
|
.detect = detect_hdmi,
|
|
.enable = do_enable_hdmi,
|
|
.mode = {
|
|
.name = "HDMI",
|
|
/* 1024x768@60Hz (VESA)*/
|
|
.refresh = 60,
|
|
.xres = 1024,
|
|
.yres = 768,
|
|
.pixclock = 15384,
|
|
.left_margin = 160,
|
|
.right_margin = 24,
|
|
.upper_margin = 29,
|
|
.lower_margin = 3,
|
|
.hsync_len = 136,
|
|
.vsync_len = 6,
|
|
.sync = FB_SYNC_EXT,
|
|
.vmode = FB_VMODE_NONINTERLACED
|
|
}
|
|
}
|
|
};
|
|
|
|
size_t display_count = ARRAY_SIZE(displays);
|
|
|
|
static int setup_display(void)
|
|
{
|
|
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
int reg;
|
|
int timeout = 100000;
|
|
|
|
enable_ipu_clock();
|
|
imx_setup_hdmi();
|
|
|
|
/* set video pll to 455MHz (24MHz * (37+11/12) / 2) */
|
|
setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
|
|
|
|
reg = readl(&ccm->analog_pll_video);
|
|
reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
|
|
reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(37);
|
|
reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
|
|
reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1);
|
|
writel(reg, &ccm->analog_pll_video);
|
|
|
|
writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
|
|
writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
|
|
|
|
reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
|
|
writel(reg, &ccm->analog_pll_video);
|
|
|
|
while (timeout--)
|
|
if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
|
|
break;
|
|
if (timeout < 0) {
|
|
printf("Warning: video pll lock timeout!\n");
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
reg = readl(&ccm->analog_pll_video);
|
|
reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
|
|
reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
|
|
writel(reg, &ccm->analog_pll_video);
|
|
|
|
/* gate ipu1_di0_clk */
|
|
clrbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
|
|
|
|
/* select video_pll clock / 7 for ipu1_di0_clk -> 65MHz pixclock */
|
|
reg = readl(&ccm->chsccdr);
|
|
reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK |
|
|
MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK |
|
|
MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
|
|
reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET) |
|
|
(6 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) |
|
|
(0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
|
|
writel(reg, &ccm->chsccdr);
|
|
|
|
/* enable ipu1_di0_clk */
|
|
setbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
|
|
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_VIDEO_IPUV3 */
|
|
|
|
#ifdef CONFIG_USB_EHCI_MX6
|
|
static void setup_usb(void)
|
|
{
|
|
SETUP_IOMUX_PADS(usb_pads);
|
|
}
|
|
|
|
int board_ehci_hcd_init(int port)
|
|
{
|
|
if (port == 1)
|
|
gpio_direction_output(USB_H1_VBUS, 1);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
setup_iomux_uart();
|
|
|
|
#ifdef CONFIG_CMD_SATA
|
|
setup_sata();
|
|
#endif
|
|
|
|
#ifdef CONFIG_USB_EHCI_MX6
|
|
setup_usb();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
int ret = 0;
|
|
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
#ifdef CONFIG_VIDEO_IPUV3
|
|
ret = setup_display();
|
|
#endif
|
|
|
|
return ret;
|
|
}
|
|
|
|
static enum board_type board_type(void)
|
|
{
|
|
int val1, val2, val3;
|
|
|
|
SETUP_IOMUX_PADS(board_detect);
|
|
|
|
/*
|
|
* Machine selection -
|
|
* Machine val1, val2, val3
|
|
* ----------------------------
|
|
* HB2 x x 0
|
|
* HB rev 3.x x 0 x
|
|
* CBi 0 1 x
|
|
* HB 1 1 x
|
|
*/
|
|
|
|
gpio_direction_input(IMX_GPIO_NR(2, 8));
|
|
val3 = gpio_get_value(IMX_GPIO_NR(2, 8));
|
|
|
|
if (val3 == 0)
|
|
return HUMMINGBOARD2;
|
|
|
|
gpio_direction_input(IMX_GPIO_NR(3, 4));
|
|
val2 = gpio_get_value(IMX_GPIO_NR(3, 4));
|
|
|
|
if (val2 == 0)
|
|
return HUMMINGBOARD;
|
|
|
|
gpio_direction_input(IMX_GPIO_NR(4, 9));
|
|
val1 = gpio_get_value(IMX_GPIO_NR(4, 9));
|
|
|
|
if (val1 == 0) {
|
|
return CUBOXI;
|
|
} else {
|
|
return HUMMINGBOARD;
|
|
}
|
|
}
|
|
|
|
static bool is_rev_15_som(void)
|
|
{
|
|
int val1, val2;
|
|
SETUP_IOMUX_PADS(som_rev_detect);
|
|
|
|
val1 = gpio_get_value(IMX_GPIO_NR(6, 0));
|
|
val2 = gpio_get_value(IMX_GPIO_NR(6, 4));
|
|
|
|
if (val1 == 1 && val2 == 0)
|
|
return true;
|
|
|
|
return false;
|
|
}
|
|
|
|
static bool has_emmc(void)
|
|
{
|
|
struct mmc *mmc;
|
|
mmc = find_mmc_device(1);
|
|
if (!mmc)
|
|
return 0;
|
|
return (mmc_get_op_cond(mmc) < 0) ? 0 : 1;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
switch (board_type()) {
|
|
case CUBOXI:
|
|
puts("Board: MX6 Cubox-i");
|
|
break;
|
|
case HUMMINGBOARD:
|
|
puts("Board: MX6 HummingBoard");
|
|
break;
|
|
case HUMMINGBOARD2:
|
|
puts("Board: MX6 HummingBoard2");
|
|
break;
|
|
case UNKNOWN:
|
|
default:
|
|
puts("Board: Unknown\n");
|
|
goto out;
|
|
}
|
|
|
|
if (is_rev_15_som())
|
|
puts(" (som rev 1.5)\n");
|
|
else
|
|
puts("\n");
|
|
|
|
out:
|
|
return 0;
|
|
}
|
|
|
|
int board_late_init(void)
|
|
{
|
|
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
|
|
switch (board_type()) {
|
|
case CUBOXI:
|
|
env_set("board_name", "CUBOXI");
|
|
break;
|
|
case HUMMINGBOARD:
|
|
env_set("board_name", "HUMMINGBOARD");
|
|
break;
|
|
case HUMMINGBOARD2:
|
|
env_set("board_name", "HUMMINGBOARD2");
|
|
break;
|
|
case UNKNOWN:
|
|
default:
|
|
env_set("board_name", "CUBOXI");
|
|
}
|
|
|
|
if (is_mx6dq())
|
|
env_set("board_rev", "MX6Q");
|
|
else
|
|
env_set("board_rev", "MX6DL");
|
|
|
|
if (is_rev_15_som())
|
|
env_set("som_rev", "V15");
|
|
|
|
if (has_emmc())
|
|
env_set("has_emmc", "yes");
|
|
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
#include <asm/arch/mx6-ddr.h>
|
|
static const struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = {
|
|
.dram_sdclk_0 = 0x00020030,
|
|
.dram_sdclk_1 = 0x00020030,
|
|
.dram_cas = 0x00020030,
|
|
.dram_ras = 0x00020030,
|
|
.dram_reset = 0x000c0030,
|
|
.dram_sdcke0 = 0x00003000,
|
|
.dram_sdcke1 = 0x00003000,
|
|
.dram_sdba2 = 0x00000000,
|
|
.dram_sdodt0 = 0x00003030,
|
|
.dram_sdodt1 = 0x00003030,
|
|
.dram_sdqs0 = 0x00000030,
|
|
.dram_sdqs1 = 0x00000030,
|
|
.dram_sdqs2 = 0x00000030,
|
|
.dram_sdqs3 = 0x00000030,
|
|
.dram_sdqs4 = 0x00000030,
|
|
.dram_sdqs5 = 0x00000030,
|
|
.dram_sdqs6 = 0x00000030,
|
|
.dram_sdqs7 = 0x00000030,
|
|
.dram_dqm0 = 0x00020030,
|
|
.dram_dqm1 = 0x00020030,
|
|
.dram_dqm2 = 0x00020030,
|
|
.dram_dqm3 = 0x00020030,
|
|
.dram_dqm4 = 0x00020030,
|
|
.dram_dqm5 = 0x00020030,
|
|
.dram_dqm6 = 0x00020030,
|
|
.dram_dqm7 = 0x00020030,
|
|
};
|
|
|
|
static const struct mx6sdl_iomux_ddr_regs mx6dl_ddr_ioregs = {
|
|
.dram_sdclk_0 = 0x00000028,
|
|
.dram_sdclk_1 = 0x00000028,
|
|
.dram_cas = 0x00000028,
|
|
.dram_ras = 0x00000028,
|
|
.dram_reset = 0x000c0028,
|
|
.dram_sdcke0 = 0x00003000,
|
|
.dram_sdcke1 = 0x00003000,
|
|
.dram_sdba2 = 0x00000000,
|
|
.dram_sdodt0 = 0x00003030,
|
|
.dram_sdodt1 = 0x00003030,
|
|
.dram_sdqs0 = 0x00000028,
|
|
.dram_sdqs1 = 0x00000028,
|
|
.dram_sdqs2 = 0x00000028,
|
|
.dram_sdqs3 = 0x00000028,
|
|
.dram_sdqs4 = 0x00000028,
|
|
.dram_sdqs5 = 0x00000028,
|
|
.dram_sdqs6 = 0x00000028,
|
|
.dram_sdqs7 = 0x00000028,
|
|
.dram_dqm0 = 0x00000028,
|
|
.dram_dqm1 = 0x00000028,
|
|
.dram_dqm2 = 0x00000028,
|
|
.dram_dqm3 = 0x00000028,
|
|
.dram_dqm4 = 0x00000028,
|
|
.dram_dqm5 = 0x00000028,
|
|
.dram_dqm6 = 0x00000028,
|
|
.dram_dqm7 = 0x00000028,
|
|
};
|
|
|
|
static const struct mx6dq_iomux_grp_regs mx6q_grp_ioregs = {
|
|
.grp_ddr_type = 0x000C0000,
|
|
.grp_ddrmode_ctl = 0x00020000,
|
|
.grp_ddrpke = 0x00000000,
|
|
.grp_addds = 0x00000030,
|
|
.grp_ctlds = 0x00000030,
|
|
.grp_ddrmode = 0x00020000,
|
|
.grp_b0ds = 0x00000030,
|
|
.grp_b1ds = 0x00000030,
|
|
.grp_b2ds = 0x00000030,
|
|
.grp_b3ds = 0x00000030,
|
|
.grp_b4ds = 0x00000030,
|
|
.grp_b5ds = 0x00000030,
|
|
.grp_b6ds = 0x00000030,
|
|
.grp_b7ds = 0x00000030,
|
|
};
|
|
|
|
static const struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
|
|
.grp_ddr_type = 0x000c0000,
|
|
.grp_ddrmode_ctl = 0x00020000,
|
|
.grp_ddrpke = 0x00000000,
|
|
.grp_addds = 0x00000028,
|
|
.grp_ctlds = 0x00000028,
|
|
.grp_ddrmode = 0x00020000,
|
|
.grp_b0ds = 0x00000028,
|
|
.grp_b1ds = 0x00000028,
|
|
.grp_b2ds = 0x00000028,
|
|
.grp_b3ds = 0x00000028,
|
|
.grp_b4ds = 0x00000028,
|
|
.grp_b5ds = 0x00000028,
|
|
.grp_b6ds = 0x00000028,
|
|
.grp_b7ds = 0x00000028,
|
|
};
|
|
|
|
/* microSOM with Dual processor and 1GB memory */
|
|
static const struct mx6_mmdc_calibration mx6q_1g_mmcd_calib = {
|
|
.p0_mpwldectrl0 = 0x00000000,
|
|
.p0_mpwldectrl1 = 0x00000000,
|
|
.p1_mpwldectrl0 = 0x00000000,
|
|
.p1_mpwldectrl1 = 0x00000000,
|
|
.p0_mpdgctrl0 = 0x0314031c,
|
|
.p0_mpdgctrl1 = 0x023e0304,
|
|
.p1_mpdgctrl0 = 0x03240330,
|
|
.p1_mpdgctrl1 = 0x03180260,
|
|
.p0_mprddlctl = 0x3630323c,
|
|
.p1_mprddlctl = 0x3436283a,
|
|
.p0_mpwrdlctl = 0x36344038,
|
|
.p1_mpwrdlctl = 0x422a423c,
|
|
};
|
|
|
|
/* microSOM with Quad processor and 2GB memory */
|
|
static const struct mx6_mmdc_calibration mx6q_2g_mmcd_calib = {
|
|
.p0_mpwldectrl0 = 0x00000000,
|
|
.p0_mpwldectrl1 = 0x00000000,
|
|
.p1_mpwldectrl0 = 0x00000000,
|
|
.p1_mpwldectrl1 = 0x00000000,
|
|
.p0_mpdgctrl0 = 0x0314031c,
|
|
.p0_mpdgctrl1 = 0x023e0304,
|
|
.p1_mpdgctrl0 = 0x03240330,
|
|
.p1_mpdgctrl1 = 0x03180260,
|
|
.p0_mprddlctl = 0x3630323c,
|
|
.p1_mprddlctl = 0x3436283a,
|
|
.p0_mpwrdlctl = 0x36344038,
|
|
.p1_mpwrdlctl = 0x422a423c,
|
|
};
|
|
|
|
/* microSOM with Solo processor and 512MB memory */
|
|
static const struct mx6_mmdc_calibration mx6dl_512m_mmcd_calib = {
|
|
.p0_mpwldectrl0 = 0x0045004D,
|
|
.p0_mpwldectrl1 = 0x003A0047,
|
|
.p0_mpdgctrl0 = 0x023C0224,
|
|
.p0_mpdgctrl1 = 0x02000220,
|
|
.p0_mprddlctl = 0x44444846,
|
|
.p0_mpwrdlctl = 0x32343032,
|
|
};
|
|
|
|
/* microSOM with Dual lite processor and 1GB memory */
|
|
static const struct mx6_mmdc_calibration mx6dl_1g_mmcd_calib = {
|
|
.p0_mpwldectrl0 = 0x0045004D,
|
|
.p0_mpwldectrl1 = 0x003A0047,
|
|
.p1_mpwldectrl0 = 0x001F001F,
|
|
.p1_mpwldectrl1 = 0x00210035,
|
|
.p0_mpdgctrl0 = 0x023C0224,
|
|
.p0_mpdgctrl1 = 0x02000220,
|
|
.p1_mpdgctrl0 = 0x02200220,
|
|
.p1_mpdgctrl1 = 0x02040208,
|
|
.p0_mprddlctl = 0x44444846,
|
|
.p1_mprddlctl = 0x4042463C,
|
|
.p0_mpwrdlctl = 0x32343032,
|
|
.p1_mpwrdlctl = 0x36363430,
|
|
};
|
|
|
|
static struct mx6_ddr3_cfg mem_ddr_2g = {
|
|
.mem_speed = 1600,
|
|
.density = 2,
|
|
.width = 16,
|
|
.banks = 8,
|
|
.rowaddr = 14,
|
|
.coladdr = 10,
|
|
.pagesz = 2,
|
|
.trcd = 1375,
|
|
.trcmin = 4875,
|
|
.trasmin = 3500,
|
|
};
|
|
|
|
static struct mx6_ddr3_cfg mem_ddr_4g = {
|
|
.mem_speed = 1600,
|
|
.density = 4,
|
|
.width = 16,
|
|
.banks = 8,
|
|
.rowaddr = 16,
|
|
.coladdr = 10,
|
|
.pagesz = 2,
|
|
.trcd = 1375,
|
|
.trcmin = 4875,
|
|
.trasmin = 3500,
|
|
};
|
|
|
|
static void ccgr_init(void)
|
|
{
|
|
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
|
|
writel(0x00C03F3F, &ccm->CCGR0);
|
|
writel(0x0030FC03, &ccm->CCGR1);
|
|
writel(0x0FFFC000, &ccm->CCGR2);
|
|
writel(0x3FF00000, &ccm->CCGR3);
|
|
writel(0x00FFF300, &ccm->CCGR4);
|
|
writel(0x0F0000C3, &ccm->CCGR5);
|
|
writel(0x000003FF, &ccm->CCGR6);
|
|
}
|
|
|
|
static void spl_dram_init(int width)
|
|
{
|
|
struct mx6_ddr_sysinfo sysinfo = {
|
|
/* width of data bus: 0=16, 1=32, 2=64 */
|
|
.dsize = width / 32,
|
|
/* config for full 4GB range so that get_mem_size() works */
|
|
.cs_density = 32, /* 32Gb per CS */
|
|
.ncs = 1, /* single chip select */
|
|
.cs1_mirror = 0,
|
|
.rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
|
|
.rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
|
|
.walat = 1, /* Write additional latency */
|
|
.ralat = 5, /* Read additional latency */
|
|
.mif3_mode = 3, /* Command prediction working mode */
|
|
.bi_on = 1, /* Bank interleaving enabled */
|
|
.sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
|
|
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
|
|
.ddr_type = DDR_TYPE_DDR3,
|
|
.refsel = 1, /* Refresh cycles at 32KHz */
|
|
.refr = 7, /* 8 refresh commands per refresh cycle */
|
|
};
|
|
|
|
if (is_mx6dq())
|
|
mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs);
|
|
else
|
|
mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs);
|
|
|
|
if (is_cpu_type(MXC_CPU_MX6D))
|
|
mx6_dram_cfg(&sysinfo, &mx6q_1g_mmcd_calib, &mem_ddr_2g);
|
|
else if (is_cpu_type(MXC_CPU_MX6Q))
|
|
mx6_dram_cfg(&sysinfo, &mx6q_2g_mmcd_calib, &mem_ddr_4g);
|
|
else if (is_cpu_type(MXC_CPU_MX6DL))
|
|
mx6_dram_cfg(&sysinfo, &mx6dl_1g_mmcd_calib, &mem_ddr_2g);
|
|
else if (is_cpu_type(MXC_CPU_MX6SOLO))
|
|
mx6_dram_cfg(&sysinfo, &mx6dl_512m_mmcd_calib, &mem_ddr_2g);
|
|
}
|
|
|
|
void board_init_f(ulong dummy)
|
|
{
|
|
/* setup AIPS and disable watchdog */
|
|
arch_cpu_init();
|
|
|
|
ccgr_init();
|
|
gpr_init();
|
|
|
|
/* iomux and setup of i2c */
|
|
board_early_init_f();
|
|
|
|
/* setup GP timer */
|
|
timer_init();
|
|
|
|
/* UART clocks enabled and gd valid - init serial console */
|
|
preloader_console_init();
|
|
|
|
/* DDR initialization */
|
|
if (is_cpu_type(MXC_CPU_MX6SOLO))
|
|
spl_dram_init(32);
|
|
else
|
|
spl_dram_init(64);
|
|
|
|
/* Clear the BSS. */
|
|
memset(__bss_start, 0, __bss_end - __bss_start);
|
|
|
|
/* load/boot image from boot device */
|
|
board_init_r(NULL, 0);
|
|
}
|
|
#endif
|