uboot/u-boot-stm32mp-2020.01/board/menlo/m53menlo/m53menlo.c

540 lines
13 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Menlosystems M53Menlo board
*
* Copyright (C) 2012-2017 Marek Vasut <marex@denx.de>
* Copyright (C) 2014-2017 Olaf Mandel <o.mandel@menlosystems.com>
*/
#include <common.h>
#include <dm.h>
#include <init.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/clock.h>
#include <asm/arch/iomux-mx53.h>
#include <asm/mach-imx/mx5_video.h>
#include <asm/mach-imx/video.h>
#include <asm/gpio.h>
#include <asm/spl.h>
#include <env.h>
#include <fdt_support.h>
#include <fsl_esdhc_imx.h>
#include <gzip.h>
#include <i2c.h>
#include <ipu_pixfmt.h>
#include <linux/errno.h>
#include <linux/fb.h>
#include <mmc.h>
#include <netdev.h>
#include <spl.h>
#include <splash.h>
#include <usb/ehci-ci.h>
#include <video_console.h>
DECLARE_GLOBAL_DATA_PTR;
static u32 mx53_dram_size[2];
ulong board_get_usable_ram_top(ulong total_size)
{
/*
* WARNING: We must override get_effective_memsize() function here
* to report only the size of the first DRAM bank. This is to make
* U-Boot relocator place U-Boot into valid memory, that is, at the
* end of the first DRAM bank. If we did not override this function
* like so, U-Boot would be placed at the address of the first DRAM
* bank + total DRAM size - sizeof(uboot), which in the setup where
* each DRAM bank contains 512MiB of DRAM would result in placing
* U-Boot into invalid memory area close to the end of the first
* DRAM bank.
*/
return PHYS_SDRAM_2 + mx53_dram_size[1];
}
int dram_init(void)
{
mx53_dram_size[0] = get_ram_size((void *)PHYS_SDRAM_1, 1 << 30);
mx53_dram_size[1] = get_ram_size((void *)PHYS_SDRAM_2, 1 << 30);
gd->ram_size = mx53_dram_size[0] + mx53_dram_size[1];
return 0;
}
int dram_init_banksize(void)
{
gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
gd->bd->bi_dram[0].size = mx53_dram_size[0];
gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
gd->bd->bi_dram[1].size = mx53_dram_size[1];
return 0;
}
static void setup_iomux_uart(void)
{
static const iomux_v3_cfg_t uart_pads[] = {
MX53_PAD_PATA_DMACK__UART1_RXD_MUX,
MX53_PAD_PATA_DIOW__UART1_TXD_MUX,
};
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
}
static void setup_iomux_fec(void)
{
static const iomux_v3_cfg_t fec_pads[] = {
/* MDIO pads */
NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS |
PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP | PAD_CTL_ODE),
NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH),
/* FEC 0 pads */
NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH),
/* FEC 1 pads */
NEW_PAD_CTRL(MX53_PAD_KEY_COL0__FEC_RDATA_3,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_KEY_ROW0__FEC_TX_ER,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_KEY_COL1__FEC_RX_CLK,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_KEY_ROW1__FEC_COL,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_KEY_COL2__FEC_RDATA_2,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_KEY_ROW2__FEC_TDATA_2, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_KEY_COL3__FEC_CRS,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_GPIO_19__FEC_TDATA_3, PAD_CTL_DSE_HIGH),
};
imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
}
#ifdef CONFIG_FSL_ESDHC_IMX
struct fsl_esdhc_cfg esdhc_cfg = {
MMC_SDHC1_BASE_ADDR,
};
int board_mmc_getcd(struct mmc *mmc)
{
imx_iomux_v3_setup_pad(MX53_PAD_GPIO_1__GPIO1_1);
gpio_direction_input(IMX_GPIO_NR(1, 1));
return !gpio_get_value(IMX_GPIO_NR(1, 1));
}
#define SD_CMD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
PAD_CTL_PUS_100K_UP)
#define SD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
PAD_CTL_DSE_HIGH)
int board_mmc_init(bd_t *bis)
{
static const iomux_v3_cfg_t sd1_pads[] = {
NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL),
};
esdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
imx_iomux_v3_setup_multiple_pads(sd1_pads, ARRAY_SIZE(sd1_pads));
return fsl_esdhc_initialize(bis, &esdhc_cfg);
}
#endif
static void enable_lvds_clock(struct display_info_t const *dev, const u8 hclk)
{
static struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)MXC_CCM_BASE;
int ret;
/* For ETM0430G0DH6 model, this must be enabled before the clock. */
gpio_direction_output(IMX_GPIO_NR(6, 0), 1);
/*
* Set LVDS clock to 33.28 MHz for the display. The PLL4 is set to
* 233 MHz, divided by 7 by setting CCM_CSCMR2 LDB_DI0_IPU_DIV=1 .
*/
ret = mxc_set_clock(MXC_HCLK, hclk, MXC_LDB_CLK);
if (ret)
puts("IPU: Failed to configure LDB clock\n");
/* Configure CCM_CSCMR2 */
clrsetbits_le32(&mxc_ccm->cscmr2,
(0x7 << 26) | BIT(10) | BIT(8),
(0x5 << 26) | BIT(10) | BIT(8));
/* Configure LDB_CTRL */
writel(0x201, 0x53fa8008);
}
static void enable_lvds_etm0430g0dh6(struct display_info_t const *dev)
{
gpio_request(IMX_GPIO_NR(6, 0), "LCD");
/* For ETM0430G0DH6 model, this must be enabled before the clock. */
gpio_direction_output(IMX_GPIO_NR(6, 0), 1);
/*
* Set LVDS clock to 9 MHz for the display. The PLL4 is set to
* 63 MHz, divided by 7 by setting CCM_CSCMR2 LDB_DI0_IPU_DIV=1 .
*/
enable_lvds_clock(dev, 63);
}
static void enable_lvds_etm0700g0dh6(struct display_info_t const *dev)
{
gpio_request(IMX_GPIO_NR(6, 0), "LCD");
/*
* Set LVDS clock to 33.28 MHz for the display. The PLL4 is set to
* 233 MHz, divided by 7 by setting CCM_CSCMR2 LDB_DI0_IPU_DIV=1 .
*/
enable_lvds_clock(dev, 233);
/* For ETM0700G0DH6 model, this may be enabled after the clock. */
gpio_direction_output(IMX_GPIO_NR(6, 0), 1);
}
static const char *lvds_compat_string;
static int detect_lvds(struct display_info_t const *dev)
{
u8 touchid[23];
u8 *touchptr = &touchid[0];
int ret;
ret = i2c_set_bus_num(0);
if (ret)
return 0;
/* Touchscreen is at address 0x38, ID register is 0xbb. */
ret = i2c_read(0x38, 0xbb, 1, touchid, sizeof(touchid));
if (ret)
return 0;
/* EP0430 prefixes the response with 0xbb, skip it. */
if (*touchptr == 0xbb)
touchptr++;
/* Skip the 'EP' prefix. */
touchptr += 2;
ret = !memcmp(touchptr, &dev->mode.name[7], 4);
if (ret)
lvds_compat_string = dev->mode.name;
return ret;
}
void board_preboot_os(void)
{
/* Power off the LCD to prevent awful color flicker */
gpio_direction_output(IMX_GPIO_NR(6, 0), 0);
}
int ft_board_setup(void *blob, bd_t *bd)
{
if (lvds_compat_string)
do_fixup_by_path_string(blob, "/panel", "compatible",
lvds_compat_string);
return 0;
}
struct display_info_t const displays[] = {
{
.bus = 0,
.addr = 0,
.detect = detect_lvds,
.enable = enable_lvds_etm0430g0dh6,
.pixfmt = IPU_PIX_FMT_RGB666,
.mode = {
.name = "edt,etm0430g0dh6",
.refresh = 60,
.xres = 480,
.yres = 272,
.pixclock = 111111, /* picosecond (9 MHz) */
.left_margin = 2,
.right_margin = 2,
.upper_margin = 2,
.lower_margin = 2,
.hsync_len = 41,
.vsync_len = 10,
.sync = 0x40000000,
.vmode = FB_VMODE_NONINTERLACED
}
}, {
.bus = 0,
.addr = 0,
.detect = detect_lvds,
.enable = enable_lvds_etm0700g0dh6,
.pixfmt = IPU_PIX_FMT_RGB666,
.mode = {
.name = "edt,etm0700g0dh6",
.refresh = 60,
.xres = 800,
.yres = 480,
.pixclock = 30048, /* picosecond (33.28 MHz) */
.left_margin = 40,
.right_margin = 88,
.upper_margin = 10,
.lower_margin = 33,
.hsync_len = 128,
.vsync_len = 2,
.sync = FB_SYNC_EXT,
.vmode = FB_VMODE_NONINTERLACED
}
}
};
size_t display_count = ARRAY_SIZE(displays);
#ifdef CONFIG_SPLASH_SCREEN
static struct splash_location default_splash_locations[] = {
{
.name = "mmc_fs",
.storage = SPLASH_STORAGE_MMC,
.flags = SPLASH_STORAGE_FS,
.devpart = "0:1",
},
};
int splash_screen_prepare(void)
{
return splash_source_load(default_splash_locations,
ARRAY_SIZE(default_splash_locations));
}
#endif
int board_late_init(void)
{
#if defined(CONFIG_VIDEO_IPUV3)
struct udevice *dev;
int xpos, ypos, ret;
char *s;
void *dst;
ulong addr, len;
splash_get_pos(&xpos, &ypos);
s = env_get("splashimage");
if (!s)
return 0;
addr = simple_strtoul(s, NULL, 16);
dst = malloc(CONFIG_SYS_VIDEO_LOGO_MAX_SIZE);
if (!dst)
return -ENOMEM;
ret = splash_screen_prepare();
if (ret < 0)
return ret;
len = CONFIG_SYS_VIDEO_LOGO_MAX_SIZE;
ret = gunzip(dst + 2, CONFIG_SYS_VIDEO_LOGO_MAX_SIZE - 2,
(uchar *)addr, &len);
if (ret) {
printf("Error: no valid bmp or bmp.gz image at %lx\n", addr);
free(dst);
return ret;
}
ret = uclass_get_device(UCLASS_VIDEO, 0, &dev);
if (ret)
return ret;
ret = video_bmp_display(dev, (ulong)dst + 2, xpos, ypos, true);
if (ret)
return ret;
#endif
return 0;
}
#define I2C_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
static void setup_iomux_i2c(void)
{
static const iomux_v3_cfg_t i2c_pads[] = {
/* I2C1 */
NEW_PAD_CTRL(MX53_PAD_EIM_D28__I2C1_SDA, I2C_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_EIM_D21__I2C1_SCL, I2C_PAD_CTRL),
/* I2C2 */
NEW_PAD_CTRL(MX53_PAD_EIM_D16__I2C2_SDA, I2C_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_EIM_EB2__I2C2_SCL, I2C_PAD_CTRL),
};
imx_iomux_v3_setup_multiple_pads(i2c_pads, ARRAY_SIZE(i2c_pads));
}
static void setup_iomux_video(void)
{
static const iomux_v3_cfg_t lcd_pads[] = {
MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3,
MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK,
MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2,
MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1,
MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0,
};
imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
}
static void setup_iomux_nand(void)
{
static const iomux_v3_cfg_t nand_pads[] = {
NEW_PAD_CTRL(MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B,
PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B,
PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_NANDF_CLE__EMI_NANDF_CLE,
PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_NANDF_ALE__EMI_NANDF_ALE,
PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B,
PAD_CTL_PUS_100K_UP),
NEW_PAD_CTRL(MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0,
PAD_CTL_PUS_100K_UP),
NEW_PAD_CTRL(MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0,
PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__EMI_NANDF_D_0,
PAD_CTL_DSE_HIGH | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__EMI_NANDF_D_1,
PAD_CTL_DSE_HIGH | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__EMI_NANDF_D_2,
PAD_CTL_DSE_HIGH | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__EMI_NANDF_D_3,
PAD_CTL_DSE_HIGH | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA4__EMI_NANDF_D_4,
PAD_CTL_DSE_HIGH | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA5__EMI_NANDF_D_5,
PAD_CTL_DSE_HIGH | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA6__EMI_NANDF_D_6,
PAD_CTL_DSE_HIGH | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA7__EMI_NANDF_D_7,
PAD_CTL_DSE_HIGH | PAD_CTL_PKE),
};
imx_iomux_v3_setup_multiple_pads(nand_pads, ARRAY_SIZE(nand_pads));
}
static void m53_set_clock(void)
{
int ret;
const u32 ref_clk = MXC_HCLK;
const u32 dramclk = 400;
u32 cpuclk;
gpio_request(IMX_GPIO_NR(4, 0), "CPUCLK");
imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX53_PAD_GPIO_10__GPIO4_0,
PAD_CTL_DSE_HIGH | PAD_CTL_PKE));
gpio_direction_input(IMX_GPIO_NR(4, 0));
/* GPIO10 selects modules' CPU speed, 1 = 1200MHz ; 0 = 800MHz */
cpuclk = gpio_get_value(IMX_GPIO_NR(4, 0)) ? 1200 : 800;
ret = mxc_set_clock(ref_clk, cpuclk, MXC_ARM_CLK);
if (ret)
printf("CPU: Switch CPU clock to %dMHz failed\n", cpuclk);
ret = mxc_set_clock(ref_clk, dramclk, MXC_PERIPH_CLK);
if (ret) {
printf("CPU: Switch peripheral clock to %dMHz failed\n",
dramclk);
}
ret = mxc_set_clock(ref_clk, dramclk, MXC_DDR_CLK);
if (ret)
printf("CPU: Switch DDR clock to %dMHz failed\n", dramclk);
}
static void m53_set_nand(void)
{
u32 i;
/* NAND flash is muxed on ATA pins */
setbits_le32(M4IF_BASE_ADDR + 0xc, M4IF_GENP_WEIM_MM_MASK);
/* Wait for Grant/Ack sequence (see EIM_CSnGCR2:MUX16_BYP_GRANT) */
for (i = 0x4; i < 0x94; i += 0x18) {
clrbits_le32(WEIM_BASE_ADDR + i,
WEIM_GCR2_MUX16_BYP_GRANT_MASK);
}
mxc_set_clock(0, 33, MXC_NFC_CLK);
enable_nfc_clk(1);
}
int board_early_init_f(void)
{
setup_iomux_uart();
setup_iomux_fec();
setup_iomux_i2c();
setup_iomux_nand();
setup_iomux_video();
m53_set_clock();
mxc_set_sata_internal_clock();
/* NAND clock @ 33MHz */
m53_set_nand();
return 0;
}
int board_init(void)
{
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
return 0;
}
int checkboard(void)
{
puts("Board: Menlosystems M53Menlo\n");
return 0;
}
/*
* NAND SPL
*/
#ifdef CONFIG_SPL_BUILD
void spl_board_init(void)
{
setup_iomux_nand();
m53_set_clock();
m53_set_nand();
}
u32 spl_boot_device(void)
{
return BOOT_DEVICE_NAND;
}
#endif