228 lines
8.9 KiB
Plaintext
228 lines
8.9 KiB
Plaintext
Introduction
|
|
============
|
|
|
|
HiKey is the first certified 96Boards Consumer Edition board. The board/SoC has: -
|
|
* HiSilicon Kirin 6220 eight-core ARM Cortex-A53 64-bit SoC running at 1.2GHz.
|
|
* ARM Mali 450-MP4 GPU
|
|
* 1GB 800MHz LPDDR3 DRAM
|
|
* 4GB eMMC Flash Storage
|
|
* microSD
|
|
* 802.11a/b/g/n WiFi, Bluetooth
|
|
|
|
The HiKey schematic can be found here: -
|
|
https://github.com/96boards/documentation/blob/master/consumer/hikey/hikey620/hardware-docs/HiKey_schematics_LeMaker_version_Rev_A1.pdf
|
|
|
|
The SoC datasheet can be found here: -
|
|
https://github.com/96boards/documentation/blob/master/consumer/hikey/hikey620/hardware-docs/Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf
|
|
|
|
Currently the u-boot port supports: -
|
|
* USB
|
|
* eMMC
|
|
* SD card
|
|
* GPIO
|
|
|
|
The HiKey U-Boot port has been tested with l-loader, booting ATF, which then boots
|
|
U-Boot as the bl33.bin executable.
|
|
|
|
Compile from source
|
|
===================
|
|
|
|
First get all the sources
|
|
|
|
> mkdir -p ~/hikey/src ~/hikey/bin
|
|
> cd ~/hikey/src
|
|
> git clone https://github.com/96boards-hikey/edk2 -b testing/hikey960_v2.5
|
|
> git clone https://github.com/ARM-software/arm-trusted-firmware
|
|
> git clone https://github.com/96boards-hikey/l-loader -b testing/hikey960_v1.2
|
|
> git clone https://github.com/96boards-hikey/OpenPlatformPkg -b testing/hikey960_v1.3.4
|
|
> git clone https://github.com/96boards-hikey/atf-fastboot
|
|
> wget https://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey/release/hisi-idt.py
|
|
|
|
Get the BL30 mcuimage.bin binary. It is shipped as part of the UEFI source.
|
|
The latest version can be obtained from the OpenPlatformPkg repo.
|
|
|
|
> cp OpenPlatformPkg/Platforms/Hisilicon/HiKey/Binary/mcuimage.bin ~/hikey/bin/
|
|
|
|
Get nvme.img binary
|
|
> wget -P ~/hikey/bin https://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey/release/nvme.img
|
|
|
|
Compile U-Boot
|
|
==============
|
|
|
|
> cd ~/hikey/src/u-boot
|
|
> make CROSS_COMPILE=aarch64-linux-gnu- hikey_config
|
|
> make CROSS_COMPILE=aarch64-linux-gnu-
|
|
> cp u-boot.bin ~/hikey/bin
|
|
|
|
Compile ARM Trusted Firmware (ATF)
|
|
==================================
|
|
|
|
> cd ~/hikey/src/arm-trusted-firmware
|
|
> make CROSS_COMPILE=aarch64-linux-gnu- all fip \
|
|
SCP_BL2=~/hikey/bin/mcuimage.bin \
|
|
BL33=~/hikey/bin/u-boot.bin DEBUG=1 PLAT=hikey
|
|
|
|
Copy the resulting FIP binary
|
|
> cp build/hikey/debug/fip.bin ~/hikey/bin
|
|
|
|
Compile ATF Fastboot
|
|
====================
|
|
|
|
> cd ~/hikey/src/atf-fastboot
|
|
> make CROSS_COMPILE=aarch64-linux-gnu- PLAT=hikey DEBUG=1
|
|
|
|
Compile l-loader
|
|
================
|
|
> cd ~/hikey/src/l-loader
|
|
> ln -sf ~/hikey/src/arm-trusted-firmware/build/hikey/debug/bl1.bin
|
|
> ln -sf ~/hikey/src/arm-trusted-firmware/build/hikey/debug/bl2.bin
|
|
> ln -sf ~/hikey/src/atf-fastboot/build/hikey/debug/bl1.bin fastboot.bin
|
|
> make hikey PTABLE_LST=aosp-8g
|
|
|
|
Copy the resulting binaries
|
|
> cp *.img ~/hikey/bin
|
|
> cp l-loader.bin ~/hikey/bin
|
|
> cp recovery.bin ~/hikey/bin
|
|
|
|
These instructions are adapted from
|
|
https://github.com/ARM-software/arm-trusted-firmware/blob/master/docs/plat/hikey.rst
|
|
|
|
FLASHING
|
|
========
|
|
|
|
1. Connect the second jumper on J15 BOOT SEL, to go into recovery mode and flash l-loader.bin with
|
|
the hisi-idt.py utility. Then connect a USB A to B mini cable from your PC to the USB OTG port of HiKey and execute the below command.
|
|
|
|
The command below assumes HiKey enumerated as the first USB serial port
|
|
|
|
> sudo python ~/hikey/src/hisi-idt.py -d /dev/ttyUSB0 --img1 ~/hikey/bin/recovery.bin
|
|
|
|
2. Once LED 0 comes on solid, HiKey board should be detected as a fastboot device.
|
|
|
|
> sudo fastboot devices
|
|
|
|
0123456789ABCDEF fastboot
|
|
|
|
3. Flash the images
|
|
|
|
> sudo fastboot flash ptable ~/hikey/bin/prm_ptable.img
|
|
> sudo fastboot flash loader ~/hikey/bin/l-loader.bin
|
|
> sudo fastboot flash fastboot ~/hikey/bin/fip.bin
|
|
> sudo fastboot flash nvme ~/hikey/bin/nvme.img
|
|
|
|
4. Disconnect second jumper on J15 BOOT SEL, and reset the board and you will now (hopefully)
|
|
have ATF, booting u-boot from eMMC.
|
|
|
|
Note: To get USB host working, also disconnect the USB OTG cable used for flashing. Otherwise you
|
|
will get 'dwc_otg_core_host_init: Timeout!' errors.
|
|
|
|
See working boot trace below on UART3 available at Low Speed Expansion header: -
|
|
|
|
NOTICE: BL2: v1.5(debug):v1.5-694-g6d4f6aea
|
|
NOTICE: BL2: Built : 09:21:42, Aug 29 2018
|
|
INFO: BL2: Doing platform setup
|
|
INFO: ddr3 rank1 init pass
|
|
INFO: succeed to set ddrc 150mhz
|
|
INFO: ddr3 rank1 init pass
|
|
INFO: succeed to set ddrc 266mhz
|
|
INFO: ddr3 rank1 init pass
|
|
INFO: succeed to set ddrc 400mhz
|
|
INFO: ddr3 rank1 init pass
|
|
INFO: succeed to set ddrc 533mhz
|
|
INFO: ddr3 rank1 init pass
|
|
INFO: succeed to set ddrc 800mhz
|
|
INFO: Samsung DDR
|
|
INFO: ddr test value:0xa5a55a5a
|
|
INFO: BL2: TrustZone: protecting 16777216 bytes of memory at 0x3f000000
|
|
INFO: BL2: TrustZone: protecting 4194304 bytes of memory at 0x3e800000
|
|
INFO: [BDID] [fff91c18] midr: 0x410fd033
|
|
INFO: init_acpu_dvfs: pmic version 17
|
|
INFO: init_acpu_dvfs: ACPU_CHIP_MAX_FREQ=0x186a00.
|
|
INFO: acpu_dvfs_volt_init: success!
|
|
INFO: acpu_dvfs_set_freq: support freq num is 5
|
|
INFO: acpu_dvfs_set_freq: start prof is 0x4
|
|
INFO: acpu_dvfs_set_freq: magic is 0x5a5ac5c5
|
|
INFO: acpu_dvfs_set_freq: voltage:
|
|
INFO: - 0: 0x49
|
|
INFO: - 1: 0x49
|
|
INFO: - 2: 0x50
|
|
INFO: - 3: 0x60
|
|
INFO: - 4: 0x78
|
|
NOTICE: acpu_dvfs_set_freq: set acpu freq success!INFO: BL2: Loading image id 2
|
|
INFO: Loading image id=2 at address 0x1000000
|
|
INFO: Image id=2 loaded: 0x1000000 - 0x1023d00
|
|
INFO: hisi_mcu_load_image: mcu sections 0:
|
|
INFO: hisi_mcu_load_image: src = 0x1000200
|
|
INFO: hisi_mcu_load_image: dst = 0xf6000000
|
|
INFO: hisi_mcu_load_image: size = 31184
|
|
INFO: hisi_mcu_load_image: [SRC 0x1000200] 0x8000 0x3701 0x7695 0x7689
|
|
INFO: hisi_mcu_load_image: [DST 0xf6000000] 0x8000 0x3701 0x7695 0x7689
|
|
INFO: hisi_mcu_load_image: mcu sections 1:
|
|
INFO: hisi_mcu_load_image: src = 0x1007bd0
|
|
INFO: hisi_mcu_load_image: dst = 0x5e00000
|
|
INFO: hisi_mcu_load_image: size = 93828
|
|
INFO: hisi_mcu_load_image: [SRC 0x1007bd0] 0xf000b510 0x2103fb3d 0xf0004604 0xf003fb57
|
|
INFO: hisi_mcu_load_image: [DST 0x5e00000] 0xf000b510 0x2103fb3d 0xf0004604 0xf003fb57
|
|
INFO: hisi_mcu_load_image: mcu sections 2:
|
|
INFO: hisi_mcu_load_image: src = 0x101ea54
|
|
INFO: hisi_mcu_load_image: dst = 0x5e16e84
|
|
INFO: hisi_mcu_load_image: size = 15428
|
|
INFO: hisi_mcu_load_image: [SRC 0x101ea54] 0x9 0x1020640 0x10001 0x8f0d180
|
|
INFO: hisi_mcu_load_image: [DST 0x5e16e84] 0x9 0x1020640 0x10001 0x8f0d180
|
|
INFO: hisi_mcu_load_image: mcu sections 3:
|
|
INFO: hisi_mcu_load_image: src = 0x1022698
|
|
INFO: hisi_mcu_load_image: dst = 0x5e22a10
|
|
INFO: hisi_mcu_load_image: size = 3060
|
|
INFO: hisi_mcu_load_image: [SRC 0x1022698] 0x0 0x0 0x0 0x0
|
|
INFO: hisi_mcu_load_image: [DST 0x5e22a10] 0x0 0x0 0x0 0x0
|
|
INFO: hisi_mcu_load_image: mcu sections 4:
|
|
INFO: hisi_mcu_load_image: src = 0x102328c
|
|
INFO: hisi_mcu_load_image: dst = 0x5e23604
|
|
INFO: hisi_mcu_load_image: size = 2616
|
|
INFO: hisi_mcu_load_image: [SRC 0x102328c] 0xf80000a0 0x0 0xf80000ac 0x0
|
|
INFO: hisi_mcu_load_image: [DST 0x5e23604] 0xf80000a0 0x0 0xf80000ac 0x0
|
|
INFO: hisi_mcu_start_run: AO_SC_SYS_CTRL2=0
|
|
INFO: plat_hikey_bl2_handle_scp_bl2: MCU PC is at 0x42933301
|
|
INFO: plat_hikey_bl2_handle_scp_bl2: AO_SC_PERIPH_CLKSTAT4 is 0x3b018f09
|
|
WARNING: BL2: Platform setup already done!!
|
|
INFO: BL2: Loading image id 3
|
|
INFO: Loading image id=3 at address 0xf9858000
|
|
INFO: Image id=3 loaded: 0xf9858000 - 0xf9860058
|
|
INFO: BL2: Loading image id 5
|
|
INFO: Loading image id=5 at address 0x35000000
|
|
INFO: Image id=5 loaded: 0x35000000 - 0x35061cd2
|
|
NOTICE: BL2: Booting BL31
|
|
INFO: Entry point address = 0xf9858000
|
|
INFO: SPSR = 0x3cd
|
|
NOTICE: BL31: v1.5(debug):v1.5-694-g6d4f6aea
|
|
NOTICE: BL31: Built : 09:21:44, Aug 29 2018
|
|
WARNING: Using deprecated integer interrupt array in gicv2_driver_data_t
|
|
WARNING: Please migrate to using an interrupt_prop_t array
|
|
INFO: ARM GICv2 driver initialized
|
|
INFO: BL31: Initializing runtime services
|
|
INFO: BL31: cortex_a53: CPU workaround for disable_non_temporal_hint was applied
|
|
INFO: BL31: cortex_a53: CPU workaround for 843419 was applied
|
|
INFO: BL31: cortex_a53: CPU workaround for 855873 was applied
|
|
INFO: BL31: Preparing for EL3 exit to normal world
|
|
INFO: Entry point address = 0x35000000
|
|
INFO: SPSR = 0x3c9
|
|
|
|
|
|
U-Boot 2018.09-rc1 (Aug 22 2018 - 14:55:49 +0530)hikey
|
|
|
|
DRAM: 990 MiB
|
|
HI6553 PMIC init
|
|
MMC: config_sd_carddetect: SD card present
|
|
Hisilicon DWMMC: 0, Hisilicon DWMMC: 1
|
|
Loading Environment from FAT... Unable to use mmc 1:1... Failed (-5)
|
|
In: uart@f7113000
|
|
Out: uart@f7113000
|
|
Err: uart@f7113000
|
|
Net: Net Initialization Skipped
|
|
No ethernet found.
|
|
Hit any key to stop autoboot: 0
|
|
starting USB...
|
|
USB0: scanning bus 0 for devices... 2 USB Device(s) found
|
|
scanning usb for storage devices... 0 Storage Device(s) found
|
|
scanning usb for ethernet devices... 0 Ethernet Device(s) found
|