149 lines
3.2 KiB
C
149 lines
3.2 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2014 Freescale Semiconductor, Inc.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <env.h>
|
|
#include <i2c.h>
|
|
#include <init.h>
|
|
#include <netdev.h>
|
|
#include <linux/compiler.h>
|
|
#include <asm/mmu.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/cache.h>
|
|
#include <asm/immap_85xx.h>
|
|
#include <asm/fsl_law.h>
|
|
#include <asm/fsl_serdes.h>
|
|
#include <asm/fsl_liodn.h>
|
|
#include <fm_eth.h>
|
|
|
|
#include "t4rdb.h"
|
|
#include "cpld.h"
|
|
#include "../common/vid.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int checkboard(void)
|
|
{
|
|
struct cpu_type *cpu = gd->arch.cpu;
|
|
u8 sw;
|
|
|
|
printf("Board: %sRDB, ", cpu->name);
|
|
printf("Board rev: 0x%02x CPLD ver: 0x%02x%02x, ",
|
|
CPLD_READ(hw_ver), CPLD_READ(sw_maj_ver), CPLD_READ(sw_min_ver));
|
|
|
|
sw = CPLD_READ(vbank);
|
|
sw = sw & CPLD_BANK_SEL_MASK;
|
|
|
|
if (sw <= 7)
|
|
printf("vBank: %d\n", sw);
|
|
else
|
|
printf("Unsupported Bank=%x\n", sw);
|
|
|
|
puts("SERDES Reference Clocks:\n");
|
|
printf(" SERDES1=100MHz SERDES2=156.25MHz\n"
|
|
" SERDES3=100MHz SERDES4=100MHz\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_early_init_r(void)
|
|
{
|
|
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
|
|
int flash_esel = find_tlb_idx((void *)flashbase, 1);
|
|
|
|
/*
|
|
* Remap Boot flash + PROMJET region to caching-inhibited
|
|
* so that flash can be erased properly.
|
|
*/
|
|
|
|
/* Flush d-cache and invalidate i-cache of any FLASH data */
|
|
flush_dcache();
|
|
invalidate_icache();
|
|
|
|
if (flash_esel == -1) {
|
|
/* very unlikely unless something is messed up */
|
|
puts("Error: Could not find TLB for FLASH BASE\n");
|
|
flash_esel = 2; /* give our best effort to continue */
|
|
} else {
|
|
/* invalidate existing TLB entry for flash + promjet */
|
|
disable_tlb(flash_esel);
|
|
}
|
|
|
|
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, flash_esel, BOOKE_PAGESZ_256M, 1);
|
|
|
|
/*
|
|
* Adjust core voltage according to voltage ID
|
|
* This function changes I2C mux to channel 2.
|
|
*/
|
|
if (adjust_vdd(0))
|
|
printf("Warning: Adjusting core voltage failed.\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
int misc_init_r(void)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
int ft_board_setup(void *blob, bd_t *bd)
|
|
{
|
|
phys_addr_t base;
|
|
phys_size_t size;
|
|
|
|
ft_cpu_setup(blob, bd);
|
|
|
|
base = env_get_bootm_low();
|
|
size = env_get_bootm_size();
|
|
|
|
fdt_fixup_memory(blob, (u64)base, (u64)size);
|
|
|
|
#ifdef CONFIG_PCI
|
|
pci_of_setup(blob, bd);
|
|
#endif
|
|
|
|
fdt_fixup_liodn(blob);
|
|
fsl_fdt_fixup_dr_usb(blob, bd);
|
|
|
|
#ifdef CONFIG_SYS_DPAA_FMAN
|
|
fdt_fixup_fman_ethernet(blob);
|
|
fdt_fixup_board_enet(blob);
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* This function is called by bdinfo to print detail board information.
|
|
* As an exmaple for future board, we organize the messages into
|
|
* several sections. If applicable, the message is in the format of
|
|
* <name> = <value>
|
|
* It should aligned with normal output of bdinfo command.
|
|
*
|
|
* Voltage: Core, DDR and another configurable voltages
|
|
* Clock : Critical clocks which are not printed already
|
|
* RCW : RCW source if not printed already
|
|
* Misc : Other important information not in above catagories
|
|
*/
|
|
void board_detail(void)
|
|
{
|
|
int rcwsrc;
|
|
|
|
/* RCW section SW3[4] */
|
|
rcwsrc = 0x0;
|
|
puts("RCW source = ");
|
|
switch (rcwsrc & 0x1) {
|
|
case 0x1:
|
|
puts("SDHC/eMMC\n");
|
|
break;
|
|
default:
|
|
puts("I2C normal addressing\n");
|
|
break;
|
|
}
|
|
}
|