98 lines
3.0 KiB
Plaintext
98 lines
3.0 KiB
Plaintext
Overview
|
|
--------
|
|
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
|
|
development platform, with a complete debugging environment.
|
|
The LS1012ARDB board supports the QorIQ LS1012A processor and is
|
|
optimized to support the high-bandwidth DDR3L memory and
|
|
a full complement of high-speed SerDes ports.
|
|
|
|
LS1012A SoC Overview
|
|
--------------------
|
|
Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A
|
|
SoC overview.
|
|
|
|
LS1012ARDB board Overview
|
|
-----------------------
|
|
- SERDES Connections, 4 lanes supporting:
|
|
- PCI Express - 3.0
|
|
- SGMII, SGMII 2.5
|
|
- SATA 3.0
|
|
- DDR Controller
|
|
- 16-bit, 1 GB DDR3L SDRAM memory, running at data rates up to 1 GT/s
|
|
-QSPI: A dual 1:3 switch, NX3L4357GM,115 (U35) drives the QSPI chip-select
|
|
signals to
|
|
- QSPI NOR flash memory (2 virtual banks)
|
|
- the QSPI emulator.s
|
|
- USB 3.0
|
|
- one high-speed USB 2.0/3.0 port.
|
|
- Two enhanced secure digital host controllers:
|
|
- SDHC1 controller can be connected to onboard SDHC connector
|
|
- SDHC2 controller: Three dual 1:4 mux/demux devices,
|
|
74CBTLV3253DS (U30, U31, U33) drive the SDHC2 signals to eMMC,
|
|
SDIO WiFi, SPI, and Ardiuno shield
|
|
- 2 I2C controllers
|
|
- One SATA onboard connectors
|
|
- UART
|
|
- The LS1012A processor consists of two UART controllers,
|
|
out of which only UART1 is used on RDB.
|
|
- ARM JTAG support
|
|
|
|
Booting Options
|
|
---------------
|
|
a) QSPI Flash Emu Boot
|
|
b) QSPI Flash 1
|
|
c) QSPI Flash 2
|
|
|
|
QSPI flash map
|
|
--------------
|
|
Images | Size |QSPI Flash Address
|
|
------------------------------------------
|
|
RCW + PBI | 1MB | 0x4000_0000
|
|
U-boot | 1MB | 0x4010_0000
|
|
U-boot Env | 1MB | 0x4020_0000
|
|
PPA FIT image | 2MB | 0x4050_0000
|
|
Linux ITB | ~53MB | 0x40A0_0000
|
|
|
|
LS1012A2G5RDB board Overview
|
|
-----------------------
|
|
- SERDES Connections, 3 lanes supporting:
|
|
- SGMII, SGMII 2.5
|
|
- SATA 3.0
|
|
- DDR Controller
|
|
- 16-bit, 1 GB DDR3L SDRAM memory, running at data rates up to 1 GT/s
|
|
-QSPI: A dual 1:3 switch, NX3L4357GM,115 (U35) drives the QSPI chip-select
|
|
signals to
|
|
- QSPI NOR flash memory
|
|
- USB 3.0
|
|
- one high-speed USB 2.0/3.0 port.
|
|
- SDIO WiFi, SPI
|
|
- 2 I2C controllers
|
|
- One SATA onboard connectors
|
|
- UART
|
|
- The LS1012A processor consists of two UART controllers,
|
|
out of which only UART1 is used on 2G5RDB.
|
|
- ARM JTAG support
|
|
|
|
Major Difference between LS1012ARDB and LS1012A-2G5RDB
|
|
------------------------------------------------------
|
|
1. LS1012A-2G5RDB has Type C USB connector unlike USB Type A/B of LS1012ARDB
|
|
2. LS1012A-2G5RDB has 2 2.5G AQR PHY unlike 2 1G Realtek RTL8211FS PHYs
|
|
of LS1012ARDB
|
|
3. LS1012A-2G5RDB is not having Arduino header
|
|
4. LS1012A-2G5RDB doesn't have PCI slot
|
|
|
|
Booting Options
|
|
---------------
|
|
QSPI Flash
|
|
|
|
QSPI flash map
|
|
--------------
|
|
Images | Size |QSPI Flash Address
|
|
------------------------------------------
|
|
RCW + PBI | 1MB | 0x4000_0000
|
|
U-boot | 1MB | 0x4010_0000
|
|
U-boot Env | 1MB | 0x4030_0000
|
|
PPA FIT image | 2MB | 0x4040_0000
|
|
PFE firmware | 20K | 0x00a0_0000
|
|
Linux ITB | ~53MB | 0x4100_0000
|