74 lines
2.3 KiB
Plaintext
74 lines
2.3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
/dts-v1/;
|
|
|
|
#include "omap36xx.dtsi"
|
|
#include "logicpd-torpedo-som.dtsi"
|
|
#include "omap-gpmc-smsc9221.dtsi"
|
|
#include "logicpd-torpedo-baseboard.dtsi"
|
|
|
|
/ {
|
|
model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit";
|
|
compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3";
|
|
|
|
wl12xx_vmmc: wl12xx_vmmc {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vwl1271";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
gpio = <&gpio5 29 0>; /* gpio157 */
|
|
startup-delay-us = <70000>;
|
|
enable-active-high;
|
|
vin-supply = <&vmmc2>;
|
|
};
|
|
};
|
|
|
|
/*
|
|
* Only found on the wireless SOM. For the SOM without wireless, the pins for
|
|
* MMC3 can be routed with jumpers to the second MMC slot on the devkit and
|
|
* gpio157 is not connected. So this should be OK to keep common for now,
|
|
* probably device tree overlays is the way to go with the various SOM and
|
|
* jumpering combinations for the long run.
|
|
*/
|
|
&mmc3 {
|
|
interrupts-extended = <&intc 94 &omap3_pmx_core 0x136>;
|
|
pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
|
|
pinctrl-names = "default";
|
|
vmmc-supply = <&wl12xx_vmmc>;
|
|
non-removable;
|
|
bus-width = <4>;
|
|
cap-power-off-card;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
wlcore: wlcore@2 {
|
|
compatible = "ti,wl1283";
|
|
reg = <2>;
|
|
interrupt-parent = <&gpio5>;
|
|
interrupts = <24 IRQ_TYPE_EDGE_RISING>; /* gpio 152 */
|
|
ref-clock-frequency = <26000000>;
|
|
tcxo-clock-frequency = <26000000>;
|
|
};
|
|
};
|
|
|
|
&omap3_pmx_core {
|
|
mmc3_pins: pinmux_mm3_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
|
|
OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
|
|
OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
|
|
OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
|
|
OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
|
|
OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&omap3_pmx_core2 {
|
|
mmc3_core2_pins: pinmux_mmc3_core2_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */
|
|
OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */
|
|
>;
|
|
};
|
|
};
|