133 lines
3.6 KiB
Plaintext
133 lines
3.6 KiB
Plaintext
STMicroelectronics STM32 Reset and Clock Controller
|
|
===================================================
|
|
|
|
The RCC IP is both a reset and a clock controller.
|
|
|
|
Please refer to clock-bindings.txt for common clock controller binding usage.
|
|
Please also refer to reset.txt for common reset controller binding usage.
|
|
|
|
Required properties:
|
|
- compatible: Should be:
|
|
"st,stm32f42xx-rcc"
|
|
"st,stm32f469-rcc"
|
|
"st,stm32f746-rcc"
|
|
- reg: should be register base and length as documented in the
|
|
datasheet
|
|
- #reset-cells: 1, see below
|
|
- #clock-cells: 2, device nodes should specify the clock in their "clocks"
|
|
property, containing a phandle to the clock device node, an index selecting
|
|
between gated clocks and other clocks and an index specifying the clock to
|
|
use.
|
|
- clocks: External oscillator clock phandle
|
|
- high speed external clock signal (HSE)
|
|
- external I2S clock (I2S_CKIN)
|
|
|
|
Example:
|
|
|
|
rcc: rcc@40023800 {
|
|
#reset-cells = <1>;
|
|
#clock-cells = <2>
|
|
compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
|
|
reg = <0x40023800 0x400>;
|
|
clocks = <&clk_hse>, <&clk_i2s_ckin>;
|
|
};
|
|
|
|
Specifying gated clocks
|
|
=======================
|
|
|
|
The primary index must be set to 0.
|
|
|
|
The secondary index is the bit number within the RCC register bank, starting
|
|
from the first RCC clock enable register (RCC_AHB1ENR, address offset 0x30).
|
|
|
|
It is calculated as: index = register_offset / 4 * 32 + bit_offset.
|
|
Where bit_offset is the bit offset within the register (LSB is 0, MSB is 31).
|
|
|
|
To simplify the usage and to share bit definition with the reset and clock
|
|
drivers of the RCC IP, macros are available to generate the index in
|
|
human-readble format.
|
|
|
|
For STM32F4 series, the macro are available here:
|
|
- include/dt-bindings/mfd/stm32f4-rcc.h
|
|
|
|
Example:
|
|
|
|
/* Gated clock, AHB1 bit 0 (GPIOA) */
|
|
... {
|
|
clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOA)>
|
|
};
|
|
|
|
/* Gated clock, AHB2 bit 4 (CRYP) */
|
|
... {
|
|
clocks = <&rcc 0 STM32F4_AHB2_CLOCK(CRYP)>
|
|
};
|
|
|
|
Specifying other clocks
|
|
=======================
|
|
|
|
The primary index must be set to 1.
|
|
|
|
The secondary index is bound with the following magic numbers:
|
|
|
|
0 SYSTICK
|
|
1 FCLK
|
|
2 CLK_LSI (low-power clock source)
|
|
3 CLK_LSE (generated from a 32.768 kHz low-speed external
|
|
crystal or ceramic resonator)
|
|
4 CLK_HSE_RTC (HSE division factor for RTC clock)
|
|
5 CLK_RTC (real-time clock)
|
|
6 PLL_VCO_I2S (vco frequency of I2S pll)
|
|
7 PLL_VCO_SAI (vco frequency of SAI pll)
|
|
8 CLK_LCD (LCD-TFT)
|
|
9 CLK_I2S (I2S clocks)
|
|
10 CLK_SAI1 (audio clocks)
|
|
11 CLK_SAI2
|
|
12 CLK_I2SQ_PDIV (post divisor of pll i2s q divisor)
|
|
13 CLK_SAIQ_PDIV (post divisor of pll sai q divisor)
|
|
|
|
14 CLK_HSI (Internal ocscillator clock)
|
|
15 CLK_SYSCLK (System Clock)
|
|
16 CLK_HDMI_CEC (HDMI-CEC clock)
|
|
17 CLK_SPDIF (SPDIF-Rx clock)
|
|
18 CLK_USART1 (U(s)arts clocks)
|
|
19 CLK_USART2
|
|
20 CLK_USART3
|
|
21 CLK_UART4
|
|
22 CLK_UART5
|
|
23 CLK_USART6
|
|
24 CLK_UART7
|
|
25 CLK_UART8
|
|
26 CLK_I2C1 (I2S clocks)
|
|
27 CLK_I2C2
|
|
28 CLK_I2C3
|
|
29 CLK_I2C4
|
|
30 CLK_LPTIMER (LPTimer1 clock)
|
|
)
|
|
|
|
Example:
|
|
|
|
/* Misc clock, FCLK */
|
|
... {
|
|
clocks = <&rcc 1 STM32F4_APB1_CLOCK(TIM2)>
|
|
};
|
|
|
|
|
|
Specifying softreset control of devices
|
|
=======================================
|
|
|
|
Device nodes should specify the reset channel required in their "resets"
|
|
property, containing a phandle to the reset device node and an index specifying
|
|
which channel to use.
|
|
The index is the bit number within the RCC registers bank, starting from RCC
|
|
base address.
|
|
It is calculated as: index = register_offset / 4 * 32 + bit_offset.
|
|
Where bit_offset is the bit offset within the register.
|
|
For example, for CRC reset:
|
|
crc = AHB1RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x10 / 4 * 32 + 12 = 140
|
|
|
|
example:
|
|
|
|
timer2 {
|
|
resets = <&rcc STM32F4_APB1_RESET(TIM2)>;
|
|
};
|