85 lines
3.1 KiB
Plaintext
85 lines
3.1 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0+
|
|
#
|
|
# Copyright (C) 2017 NXP Semiconductors
|
|
# Copyright (C) 2017 Bin Meng <bmeng.cn@gmail.com>
|
|
|
|
What is NVMe
|
|
============
|
|
|
|
NVM Express (NVMe) is a register level interface that allows host software to
|
|
communicate with a non-volatile memory subsystem. This interface is optimized
|
|
for enterprise and client solid state drives, typically attached to the PCI
|
|
express interface. It is a scalable host controller interface designed to
|
|
address the needs of enterprise and client systems that utilize PCI express
|
|
based solid state drives (SSD). The interface provides optimized command
|
|
submission and completion paths. It includes support for parallel operation by
|
|
supporting up to 64K I/O queues with up to 64K commands per I/O queue.
|
|
|
|
The device is comprised of some number of controllers, where each controller
|
|
is comprised of some number of namespaces, where each namespace is comprised
|
|
of some number of logical blocks. A namespace is a quantity of non-volatile
|
|
memory that is formatted into logical blocks. An NVMe namespace is equivalent
|
|
to a SCSI LUN. Each namespace is operated as an independent "device".
|
|
|
|
How it works
|
|
------------
|
|
There is an NVMe uclass driver (driver name "nvme"), an NVMe host controller
|
|
driver (driver name "nvme") and an NVMe namespace block driver (driver name
|
|
"nvme-blk"). The host controller driver is supposed to probe the hardware and
|
|
do necessary initialization to put the controller into a ready state at which
|
|
it is able to scan all available namespaces attached to it. Scanning namespace
|
|
is triggered by the NVMe uclass driver and the actual work is done in the NVMe
|
|
namespace block driver.
|
|
|
|
Status
|
|
------
|
|
It only support basic block read/write functions in the NVMe driver.
|
|
|
|
Config options
|
|
--------------
|
|
CONFIG_NVME Enable NVMe device support
|
|
CONFIG_CMD_NVME Enable basic NVMe commands
|
|
|
|
Usage in U-Boot
|
|
---------------
|
|
To use an NVMe hard disk from U-Boot shell, a 'nvme scan' command needs to
|
|
be executed for all NVMe hard disks attached to the NVMe controller to be
|
|
identified.
|
|
|
|
To list all of the NVMe hard disks, try:
|
|
|
|
=> nvme info
|
|
Device 0: Vendor: 0x8086 Rev: 8DV10131 Prod: CVFT535600LS400BGN
|
|
Type: Hard Disk
|
|
Capacity: 381554.0 MB = 372.6 GB (781422768 x 512)
|
|
|
|
and print out detailed information for controller and namespaces via:
|
|
|
|
=> nvme detail
|
|
|
|
Raw block read/write to can be done via the 'nvme read/write' commands:
|
|
|
|
=> nvme read a0000000 0 11000
|
|
|
|
=> tftp 80000000 /tftpboot/kernel.itb
|
|
=> nvme write 80000000 0 11000
|
|
|
|
Of course, file system command can be used on the NVMe hard disk as well:
|
|
|
|
=> fatls nvme 0:1
|
|
32376967 kernel.itb
|
|
22929408 100m
|
|
|
|
2 file(s), 0 dir(s)
|
|
|
|
=> fatload nvme 0:1 a0000000 /kernel.itb
|
|
=> bootm a0000000
|
|
|
|
Testing NVMe with QEMU x86
|
|
--------------------------
|
|
QEMU supports NVMe emulation and we can test NVMe driver with QEMU x86 running
|
|
U-Boot. Please see README.x86 for how to build u-boot.rom image for QEMU x86.
|
|
|
|
Example command line to call QEMU x86 below with emulated NVMe device:
|
|
$ ./qemu-system-i386 -drive file=nvme.img,if=none,id=drv0 -device nvme,drive=drv0,serial=QEMUNVME0001 -bios u-boot.rom
|