61 lines
1.6 KiB
C
61 lines
1.6 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* [partely copied from arch/arm/cpu/arm926ejs/at91/arm9260_devices.c]
|
|
*
|
|
* (C) Copyright 2011
|
|
* Andreas Bießmann <andreas@biessmann.org>
|
|
*
|
|
* (C) Copyright 2007-2008
|
|
* Stelian Pop <stelian@popies.net>
|
|
* Lead Tech Design <www.leadtechdesign.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/at91_common.h>
|
|
#include <asm/arch/clk.h>
|
|
#include <asm/arch/gpio.h>
|
|
|
|
/*
|
|
* if CONFIG_AT91_GPIO_PULLUP ist set, keep pullups on on all
|
|
* peripheral pins. Good to have if hardware is soldered optionally
|
|
* or in case of SPI no slave is selected. Avoid lines to float
|
|
* needlessly. Use a short local PUP define.
|
|
*
|
|
* Due to errata "TXD floats when CTS is inactive" pullups are always
|
|
* on for TXD pins.
|
|
*/
|
|
#ifdef CONFIG_AT91_GPIO_PULLUP
|
|
# define PUP CONFIG_AT91_GPIO_PULLUP
|
|
#else
|
|
# define PUP 0
|
|
#endif
|
|
|
|
void at91_serial0_hw_init(void)
|
|
{
|
|
at91_set_a_periph(AT91_PIO_PORTA, 17, 1); /* TXD0 */
|
|
at91_set_a_periph(AT91_PIO_PORTA, 18, PUP); /* RXD0 */
|
|
at91_periph_clk_enable(ATMEL_ID_USART0);
|
|
}
|
|
|
|
void at91_serial1_hw_init(void)
|
|
{
|
|
at91_set_a_periph(AT91_PIO_PORTB, 20, PUP); /* RXD1 */
|
|
at91_set_a_periph(AT91_PIO_PORTB, 21, 1); /* TXD1 */
|
|
at91_periph_clk_enable(ATMEL_ID_USART1);
|
|
}
|
|
|
|
void at91_serial2_hw_init(void)
|
|
{
|
|
at91_set_a_periph(AT91_PIO_PORTA, 22, PUP); /* RXD2 */
|
|
at91_set_a_periph(AT91_PIO_PORTA, 23, 1); /* TXD2 */
|
|
at91_periph_clk_enable(ATMEL_ID_USART2);
|
|
}
|
|
|
|
void at91_seriald_hw_init(void)
|
|
{
|
|
at91_set_a_periph(AT91_PIO_PORTA, 30, PUP); /* DRXD */
|
|
at91_set_a_periph(AT91_PIO_PORTA, 31, 1); /* DTXD */
|
|
/* writing SYS to PCER has no effect on AT91RM9200 */
|
|
}
|