238 lines
6.2 KiB
Plaintext
238 lines
6.2 KiB
Plaintext
/*
|
|
* Copyright (C) 2016 Derald D. Woods <woods.technical@gmail.com>
|
|
*
|
|
* Based on am3517-evm.dts
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
/ {
|
|
cpus {
|
|
cpu@0 {
|
|
cpu0-supply = <&vdd_core_reg>;
|
|
};
|
|
};
|
|
|
|
wl12xx_buffer: wl12xx_buf {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "wl1271_buf";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&wl12xx_buffer_pins>;
|
|
gpio = <&gpio5 1 GPIO_ACTIVE_LOW>; /* gpio 129 */
|
|
regulator-always-on;
|
|
vin-supply = <&vdd_1v8_reg>;
|
|
};
|
|
|
|
wl12xx_vmmc2: wl12xx_vmmc2 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vwl1271";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&wl12xx_wkup_pins>;
|
|
gpio = <&gpio1 3 GPIO_ACTIVE_HIGH >; /* gpio 3 */
|
|
startup-delay-us = <70000>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
vin-supply = <&wl12xx_buffer>;
|
|
};
|
|
};
|
|
|
|
&gpmc {
|
|
ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
|
|
|
|
nand@0,0 {
|
|
compatible = "ti,omap2-nand";
|
|
linux,mtd-name = "micron,mt29f4g16abchch";
|
|
reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
|
|
nand-bus-width = <16>;
|
|
ti,nand-ecc-opt = "bch8";
|
|
gpmc,sync-clk-ps = <0>;
|
|
gpmc,cs-on-ns = <0>;
|
|
gpmc,cs-rd-off-ns = <44>;
|
|
gpmc,cs-wr-off-ns = <44>;
|
|
gpmc,adv-on-ns = <6>;
|
|
gpmc,adv-rd-off-ns = <34>;
|
|
gpmc,adv-wr-off-ns = <44>;
|
|
gpmc,we-off-ns = <40>;
|
|
gpmc,oe-off-ns = <54>;
|
|
gpmc,access-ns = <64>;
|
|
gpmc,rd-cycle-ns = <82>;
|
|
gpmc,wr-cycle-ns = <82>;
|
|
gpmc,wr-access-ns = <40>;
|
|
gpmc,wr-data-mux-bus-ns = <0>;
|
|
gpmc,device-width = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
clock-frequency = <400000>;
|
|
|
|
s35390a: s35390a@30 {
|
|
compatible = "sii,s35390a";
|
|
reg = <0x30>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&rtc_pins>;
|
|
interrupts-extended = <&gpio2 23 IRQ_TYPE_EDGE_FALLING>; /* gpio_55 */
|
|
};
|
|
|
|
tps: tps65023@48 {
|
|
compatible = "ti,tps65023";
|
|
reg = <0x48>;
|
|
|
|
regulators {
|
|
vdd_core_reg: VDCDC1 {
|
|
regulator-name = "vdd_core";
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
};
|
|
|
|
vdd_io_reg: VDCDC2 {
|
|
regulator-name = "vdd_io";
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
vdd_1v8_reg: VDCDC3 {
|
|
regulator-name = "vdd_1v8";
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
vdd_usb18_reg: LDO1 {
|
|
regulator-name = "vdd_usb18";
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
vdd_usb33_reg: LDO2 {
|
|
regulator-name = "vdd_usb33";
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
touchscreen: tsc2004@4b {
|
|
compatible = "ti,tsc2004";
|
|
reg = <0x4b>;
|
|
|
|
vio-supply = <&vdd_io_reg>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&tsc2004_pins>;
|
|
interrupts-extended = <&gpio3 1 IRQ_TYPE_EDGE_RISING>; /* gpio_65 */
|
|
|
|
touchscreen-fuzz-x = <4>;
|
|
touchscreen-fuzz-y = <7>;
|
|
touchscreen-fuzz-pressure = <2>;
|
|
touchscreen-size-x = <480>;
|
|
touchscreen-size-y = <272>;
|
|
touchscreen-max-pressure = <2048>;
|
|
|
|
ti,x-plate-ohms = <280>;
|
|
ti,esd-recovery-timeout-ms = <8000>;
|
|
};
|
|
};
|
|
|
|
&mmc2 {
|
|
interrupts-extended = <&intc 86 /* &omap3_pmx_core 0x12c */>;
|
|
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc2_pins>;
|
|
vmmc-supply = <&wl12xx_vmmc2>;
|
|
non-removable;
|
|
bus-width = <4>;
|
|
cap-power-off-card;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
wlcore: wlcore@2 {
|
|
compatible = "ti,wl1271";
|
|
reg = <2>;
|
|
interrupt-parent = <&gpio6>;
|
|
interrupts = <10 IRQ_TYPE_EDGE_RISING>; /* gpio_170 */
|
|
ref-clock-frequency = <26000000>;
|
|
tcxo-clock-frequency = <26000000>;
|
|
};
|
|
};
|
|
|
|
&uart2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart2_pins>;
|
|
|
|
bluetooth {
|
|
compatible = "ti,wl1271-st";
|
|
enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; /* gpio 56 */
|
|
max-speed = <3000000>;
|
|
};
|
|
};
|
|
|
|
&omap3_pmx_core {
|
|
|
|
wl12xx_buffer_pins: pinmux_wl12xx_buffer_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4) /* mmc1_dat7.gpio_129 */
|
|
>;
|
|
};
|
|
|
|
mmc2_pins: pinmux_mmc2_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_clk.mmc2_clk */
|
|
OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_cmd.mmc2_cmd */
|
|
OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_dat0.mmc2_dat0 */
|
|
OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_dat1.mmc2_dat1 */
|
|
OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_dat2.mmc2_dat2 */
|
|
OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_dat3.mmc2_dat3 */
|
|
OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* mmc2_dat4.mmc2_dir_dat0 */
|
|
OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* mmc2_dat5.mmc2_dir_dat1 */
|
|
OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* mmc2_dat6.mmc2_dir_cmd */
|
|
OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* mmc2_dat7.mmc2_clkin */
|
|
OMAP3_CORE1_IOPAD(0x21c6, PIN_INPUT_PULLUP | MUX_MODE4) /* hdq_sio.gpio_170 */
|
|
>;
|
|
};
|
|
|
|
rtc_pins: pinmux_rtc_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x20b6, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_ncs4.gpio_55 */
|
|
>;
|
|
};
|
|
|
|
tsc2004_pins: pinmux_tsc2004_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT | MUX_MODE4) /* gpmc_wait3.gpio_65 */
|
|
>;
|
|
};
|
|
|
|
uart2_pins: pinmux_uart2_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts */
|
|
OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT_PULLUP | MUX_MODE0) /* uart2_rts */
|
|
OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
|
|
OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx */
|
|
OMAP3_CORE1_IOPAD(0x20b8, PIN_INPUT | MUX_MODE0) /* gpio_56 */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&omap3_pmx_wkup {
|
|
|
|
wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */
|
|
>;
|
|
};
|
|
};
|