/* SPDX-License-Identifier: GPL-2.0 */ /* * MIPI DSI Bus * * Copyright (C) 2012-2013, Samsung Electronics, Co., Ltd. * Copyright (C) 2018 STMicroelectronics - All Rights Reserved * Author(s): Andrzej Hajda * Yannick Fertre * Philippe Cornu * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ #ifndef MIPI_DSI_H #define MIPI_DSI_H #include struct mipi_dsi_host; struct mipi_dsi_device; /* request ACK from peripheral */ #define MIPI_DSI_MSG_REQ_ACK BIT(0) /* use Low Power Mode to transmit message */ #define MIPI_DSI_MSG_USE_LPM BIT(1) /** * struct mipi_dsi_msg - read/write DSI buffer * @channel: virtual channel id * @type: payload data type * @flags: flags controlling this message transmission * @tx_len: length of @tx_buf * @tx_buf: data to be written * @rx_len: length of @rx_buf * @rx_buf: data to be read, or NULL */ struct mipi_dsi_msg { u8 channel; u8 type; u16 flags; size_t tx_len; const void *tx_buf; size_t rx_len; void *rx_buf; }; bool mipi_dsi_packet_format_is_short(u8 type); bool mipi_dsi_packet_format_is_long(u8 type); /** * struct mipi_dsi_packet - represents a MIPI DSI packet in protocol format * @size: size (in bytes) of the packet * @header: the four bytes that make up the header (Data ID, Word Count or * Packet Data, and ECC) * @payload_length: number of bytes in the payload * @payload: a pointer to a buffer containing the payload, if any */ struct mipi_dsi_packet { size_t size; u8 header[4]; size_t payload_length; const u8 *payload; }; int mipi_dsi_create_packet(struct mipi_dsi_packet *packet, const struct mipi_dsi_msg *msg); /** * struct mipi_dsi_host_ops - DSI bus operations * @attach: attach DSI device to DSI host * @detach: detach DSI device from DSI host * @transfer: transmit a DSI packet * * DSI packets transmitted by .transfer() are passed in as mipi_dsi_msg * structures. This structure contains information about the type of packet * being transmitted as well as the transmit and receive buffers. When an * error is encountered during transmission, this function will return a * negative error code. On success it shall return the number of bytes * transmitted for write packets or the number of bytes received for read * packets. * * Note that typically DSI packet transmission is atomic, so the .transfer() * function will seldomly return anything other than the number of bytes * contained in the transmit buffer on success. */ struct mipi_dsi_host_ops { int (*attach)(struct mipi_dsi_host *host, struct mipi_dsi_device *dsi); int (*detach)(struct mipi_dsi_host *host, struct mipi_dsi_device *dsi); ssize_t (*transfer)(struct mipi_dsi_host *host, const struct mipi_dsi_msg *msg); }; /** * struct mipi_dsi_phy_ops - DSI host physical operations * @init: initialized host physical part * @get_lane_mbps: get lane bitrate per lane (mbps) * @post_set_mode: operation that should after set mode */ struct mipi_dsi_phy_ops { int (*init)(void *priv_data); int (*get_lane_mbps)(void *priv_data, struct display_timing *timings, u32 lanes, u32 format, unsigned int *lane_mbps); void (*post_set_mode)(void *priv_data, unsigned long mode_flags); }; /** * struct mipi_dsi_host - DSI host device * @dev: driver model device node for this DSI host * @ops: DSI host operations * @list: list management */ struct mipi_dsi_host { struct device *dev; const struct mipi_dsi_host_ops *ops; struct list_head list; }; /* DSI mode flags */ /* video mode */ #define MIPI_DSI_MODE_VIDEO BIT(0) /* video burst mode */ #define MIPI_DSI_MODE_VIDEO_BURST BIT(1) /* video pulse mode */ #define MIPI_DSI_MODE_VIDEO_SYNC_PULSE BIT(2) /* enable auto vertical count mode */ #define MIPI_DSI_MODE_VIDEO_AUTO_VERT BIT(3) /* enable hsync-end packets in vsync-pulse and v-porch area */ #define MIPI_DSI_MODE_VIDEO_HSE BIT(4) /* disable hfront-porch area */ #define MIPI_DSI_MODE_VIDEO_HFP BIT(5) /* disable hback-porch area */ #define MIPI_DSI_MODE_VIDEO_HBP BIT(6) /* disable hsync-active area */ #define MIPI_DSI_MODE_VIDEO_HSA BIT(7) /* flush display FIFO on vsync pulse */ #define MIPI_DSI_MODE_VSYNC_FLUSH BIT(8) /* disable EoT packets in HS mode */ #define MIPI_DSI_MODE_EOT_PACKET BIT(9) /* device supports non-continuous clock behavior (DSI spec 5.6.1) */ #define MIPI_DSI_CLOCK_NON_CONTINUOUS BIT(10) /* transmit data in low power */ #define MIPI_DSI_MODE_LPM BIT(11) enum mipi_dsi_pixel_format { MIPI_DSI_FMT_RGB888, MIPI_DSI_FMT_RGB666, MIPI_DSI_FMT_RGB666_PACKED, MIPI_DSI_FMT_RGB565, }; #define DSI_DEV_NAME_SIZE 20 /** * struct mipi_dsi_device_info - template for creating a mipi_dsi_device * @type: DSI peripheral chip type * @channel: DSI virtual channel assigned to peripheral * @node: pointer to OF device node or NULL * * This is populated and passed to mipi_dsi_device_new to create a new * DSI device */ struct mipi_dsi_device_info { char type[DSI_DEV_NAME_SIZE]; u32 channel; struct device_node *node; }; /** * struct mipi_dsi_device - DSI peripheral device * @host: DSI host for this peripheral * @dev: driver model device node for this peripheral * @name: DSI peripheral chip type * @channel: virtual channel assigned to the peripheral * @format: pixel format for video mode * @lanes: number of active data lanes * @mode_flags: DSI operation mode related flags */ struct mipi_dsi_device { struct mipi_dsi_host *host; struct udevice *dev; char name[DSI_DEV_NAME_SIZE]; unsigned int channel; unsigned int lanes; enum mipi_dsi_pixel_format format; unsigned long mode_flags; }; /** * mipi_dsi_pixel_format_to_bpp - obtain the number of bits per pixel for any * given pixel format defined by the MIPI DSI * specification * @fmt: MIPI DSI pixel format * * Returns: The number of bits per pixel of the given pixel format. */ static inline int mipi_dsi_pixel_format_to_bpp(enum mipi_dsi_pixel_format fmt) { switch (fmt) { case MIPI_DSI_FMT_RGB888: case MIPI_DSI_FMT_RGB666: return 24; case MIPI_DSI_FMT_RGB666_PACKED: return 18; case MIPI_DSI_FMT_RGB565: return 16; } return -EINVAL; } /** * struct mipi_dsi_panel_plat - DSI panel platform data * @device: DSI peripheral device * @lanes: number of active data lanes * @format: pixel format for video mode * @mode_flags: DSI operation mode related flags */ struct mipi_dsi_panel_plat { struct mipi_dsi_device *device; unsigned int lanes; enum mipi_dsi_pixel_format format; unsigned long mode_flags; }; /** * mipi_dsi_attach - attach a DSI device to its DSI host * @dsi: DSI peripheral */ int mipi_dsi_attach(struct mipi_dsi_device *dsi); /** * mipi_dsi_detach - detach a DSI device from its DSI host * @dsi: DSI peripheral */ int mipi_dsi_detach(struct mipi_dsi_device *dsi); int mipi_dsi_shutdown_peripheral(struct mipi_dsi_device *dsi); int mipi_dsi_turn_on_peripheral(struct mipi_dsi_device *dsi); int mipi_dsi_set_maximum_return_packet_size(struct mipi_dsi_device *dsi, u16 value); ssize_t mipi_dsi_generic_write(struct mipi_dsi_device *dsi, const void *payload, size_t size); ssize_t mipi_dsi_generic_read(struct mipi_dsi_device *dsi, const void *params, size_t num_params, void *data, size_t size); /** * enum mipi_dsi_dcs_tear_mode - Tearing Effect Output Line mode * @MIPI_DSI_DCS_TEAR_MODE_VBLANK: the TE output line consists of V-Blanking * information only * @MIPI_DSI_DCS_TEAR_MODE_VHBLANK : the TE output line consists of both * V-Blanking and H-Blanking information */ enum mipi_dsi_dcs_tear_mode { MIPI_DSI_DCS_TEAR_MODE_VBLANK, MIPI_DSI_DCS_TEAR_MODE_VHBLANK, }; #define MIPI_DSI_DCS_POWER_MODE_DISPLAY BIT(2) #define MIPI_DSI_DCS_POWER_MODE_NORMAL BIT(3) #define MIPI_DSI_DCS_POWER_MODE_SLEEP BIT(4) #define MIPI_DSI_DCS_POWER_MODE_PARTIAL BIT(5) #define MIPI_DSI_DCS_POWER_MODE_IDLE BIT(6) /** * mipi_dsi_dcs_write_buffer() - transmit a DCS command with payload * @dsi: DSI peripheral device * @data: buffer containing data to be transmitted * @len: size of transmission buffer * * This function will automatically choose the right data type depending on * the command payload length. * * Return: The number of bytes successfully transmitted or a negative error * code on failure. */ ssize_t mipi_dsi_dcs_write_buffer(struct mipi_dsi_device *dsi, const void *data, size_t len); /** * mipi_dsi_dcs_write() - send DCS write command * @dsi: DSI peripheral device * @cmd: DCS command * @data: buffer containing the command payload * @len: command payload length * * This function will automatically choose the right data type depending on * the command payload length. * code on failure. */ ssize_t mipi_dsi_dcs_write(struct mipi_dsi_device *dsi, u8 cmd, const void *data, size_t len); /** * mipi_dsi_dcs_read() - send DCS read request command * @dsi: DSI peripheral device * @cmd: DCS command * @data: buffer in which to receive data * @len: size of receive buffer * * Return: The number of bytes read or a negative error code on failure. */ ssize_t mipi_dsi_dcs_read(struct mipi_dsi_device *dsi, u8 cmd, void *data, size_t len); /** * mipi_dsi_dcs_nop() - send DCS nop packet * @dsi: DSI peripheral device * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_nop(struct mipi_dsi_device *dsi); /** * mipi_dsi_dcs_soft_reset() - perform a software reset of the display module * @dsi: DSI peripheral device * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_soft_reset(struct mipi_dsi_device *dsi); /** * mipi_dsi_dcs_get_power_mode() - query the display module's current power * mode * @dsi: DSI peripheral device * @mode: return location for the current power mode * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_get_power_mode(struct mipi_dsi_device *dsi, u8 *mode); /** * mipi_dsi_dcs_get_pixel_format() - gets the pixel format for the RGB image * data used by the interface * @dsi: DSI peripheral device * @format: return location for the pixel format * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_get_pixel_format(struct mipi_dsi_device *dsi, u8 *format); /** * mipi_dsi_dcs_enter_sleep_mode() - disable all unnecessary blocks inside the * display module except interface communication * @dsi: DSI peripheral device * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_enter_sleep_mode(struct mipi_dsi_device *dsi); /** * mipi_dsi_dcs_exit_sleep_mode() - enable all blocks inside the display * module * @dsi: DSI peripheral device * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_exit_sleep_mode(struct mipi_dsi_device *dsi); /** * mipi_dsi_dcs_set_display_off() - stop displaying the image data on the * display device * @dsi: DSI peripheral device * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_set_display_off(struct mipi_dsi_device *dsi); /** * mipi_dsi_dcs_set_display_on() - start displaying the image data on the * display device * @dsi: DSI peripheral device * * Return: 0 on success or a negative error code on failure */ int mipi_dsi_dcs_set_display_on(struct mipi_dsi_device *dsi); /** * mipi_dsi_dcs_set_column_address() - define the column extent of the frame * memory accessed by the host processor * @dsi: DSI peripheral device * @start: first column of frame memory * @end: last column of frame memory * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_set_column_address(struct mipi_dsi_device *dsi, u16 start, u16 end); /** * mipi_dsi_dcs_set_page_address() - define the page extent of the frame * memory accessed by the host processor * @dsi: DSI peripheral device * @start: first page of frame memory * @end: last page of frame memory * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_set_page_address(struct mipi_dsi_device *dsi, u16 start, u16 end); /** * mipi_dsi_dcs_set_tear_off() - turn off the display module's Tearing Effect * output signal on the TE signal line * @dsi: DSI peripheral device * * Return: 0 on success or a negative error code on failure */ int mipi_dsi_dcs_set_tear_off(struct mipi_dsi_device *dsi); /** * mipi_dsi_dcs_set_tear_on() - turn on the display module's Tearing Effect * output signal on the TE signal line. * @dsi: DSI peripheral device * @mode: the Tearing Effect Output Line mode * * Return: 0 on success or a negative error code on failure */ int mipi_dsi_dcs_set_tear_on(struct mipi_dsi_device *dsi, enum mipi_dsi_dcs_tear_mode mode); /** * mipi_dsi_dcs_set_pixel_format() - sets the pixel format for the RGB image * data used by the interface * @dsi: DSI peripheral device * @format: pixel format * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_set_pixel_format(struct mipi_dsi_device *dsi, u8 format); /** * mipi_dsi_dcs_set_tear_scanline() - set the scanline to use as trigger for * the Tearing Effect output signal of the display module * @dsi: DSI peripheral device * @scanline: scanline to use as trigger * * Return: 0 on success or a negative error code on failure */ int mipi_dsi_dcs_set_tear_scanline(struct mipi_dsi_device *dsi, u16 scanline); /** * mipi_dsi_dcs_set_display_brightness() - sets the brightness value of the * display * @dsi: DSI peripheral device * @brightness: brightness value * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_set_display_brightness(struct mipi_dsi_device *dsi, u16 brightness); /** * mipi_dsi_dcs_get_display_brightness() - gets the current brightness value * of the display * @dsi: DSI peripheral device * @brightness: brightness value * * Return: 0 on success or a negative error code on failure. */ int mipi_dsi_dcs_get_display_brightness(struct mipi_dsi_device *dsi, u16 *brightness); #endif /* MIPI_DSI_H */