126 lines
2.8 KiB
C
126 lines
2.8 KiB
C
|
// SPDX-License-Identifier: GPL-2.0+
|
||
|
|
/*
|
||
|
|
* Copyright (C) 2016, Bin Meng <bmeng.cn@gmail.com>
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <common.h>
|
||
|
|
#include <asm/io.h>
|
||
|
|
#include <errno.h>
|
||
|
|
#include <smsc_sio1007.h>
|
||
|
|
|
||
|
|
static inline u8 sio1007_read(int port, int reg)
|
||
|
|
{
|
||
|
|
outb(reg, port);
|
||
|
|
|
||
|
|
return inb(port + 1);
|
||
|
|
}
|
||
|
|
|
||
|
|
static inline void sio1007_write(int port, int reg, int val)
|
||
|
|
{
|
||
|
|
outb(reg, port);
|
||
|
|
outb(val, port + 1);
|
||
|
|
}
|
||
|
|
|
||
|
|
static inline void sio1007_clrsetbits(int port, int reg, u8 clr, u8 set)
|
||
|
|
{
|
||
|
|
sio1007_write(port, reg, (sio1007_read(port, reg) & ~clr) | set);
|
||
|
|
}
|
||
|
|
|
||
|
|
void sio1007_enable_serial(int port, int num, int iobase, int irq)
|
||
|
|
{
|
||
|
|
if (num < 0 || num > SIO1007_UART_NUM)
|
||
|
|
return;
|
||
|
|
|
||
|
|
/* enter configuration state */
|
||
|
|
outb(0x55, port);
|
||
|
|
|
||
|
|
/* power on serial port and set up its i/o base & irq */
|
||
|
|
if (!num) {
|
||
|
|
sio1007_clrsetbits(port, DEV_POWER_CTRL, 0, UART1_POWER_ON);
|
||
|
|
sio1007_clrsetbits(port, UART1_IOBASE, 0xfe, iobase >> 2);
|
||
|
|
sio1007_clrsetbits(port, UART_IRQ, 0xf0, irq << 4);
|
||
|
|
} else {
|
||
|
|
sio1007_clrsetbits(port, DEV_POWER_CTRL, 0, UART2_POWER_ON);
|
||
|
|
sio1007_clrsetbits(port, UART2_IOBASE, 0xfe, iobase >> 2);
|
||
|
|
sio1007_clrsetbits(port, UART_IRQ, 0x0f, irq);
|
||
|
|
}
|
||
|
|
|
||
|
|
/* exit configuration state */
|
||
|
|
outb(0xaa, port);
|
||
|
|
}
|
||
|
|
|
||
|
|
void sio1007_enable_runtime(int port, int iobase)
|
||
|
|
{
|
||
|
|
/* enter configuration state */
|
||
|
|
outb(0x55, port);
|
||
|
|
|
||
|
|
/* set i/o base for the runtime register block */
|
||
|
|
sio1007_clrsetbits(port, RTR_IOBASE_LOW, 0, iobase >> 4);
|
||
|
|
sio1007_clrsetbits(port, RTR_IOBASE_HIGH, 0, iobase >> 12);
|
||
|
|
/* turn on address decoding for this block */
|
||
|
|
sio1007_clrsetbits(port, DEV_ACTIVATE, 0, RTR_EN);
|
||
|
|
|
||
|
|
/* exit configuration state */
|
||
|
|
outb(0xaa, port);
|
||
|
|
}
|
||
|
|
|
||
|
|
void sio1007_gpio_config(int port, int gpio, int dir, int pol, int type)
|
||
|
|
{
|
||
|
|
int reg = GPIO0_DIR;
|
||
|
|
|
||
|
|
if (gpio < 0 || gpio > SIO1007_GPIO_NUM)
|
||
|
|
return;
|
||
|
|
if (gpio >= GPIO_NUM_PER_GROUP) {
|
||
|
|
reg = GPIO1_DIR;
|
||
|
|
gpio -= GPIO_NUM_PER_GROUP;
|
||
|
|
}
|
||
|
|
|
||
|
|
/* enter configuration state */
|
||
|
|
outb(0x55, port);
|
||
|
|
|
||
|
|
/* set gpio pin direction, polority and type */
|
||
|
|
sio1007_clrsetbits(port, reg, 1 << gpio, dir << gpio);
|
||
|
|
sio1007_clrsetbits(port, reg + 1, 1 << gpio, pol << gpio);
|
||
|
|
sio1007_clrsetbits(port, reg + 2, 1 << gpio, type << gpio);
|
||
|
|
|
||
|
|
/* exit configuration state */
|
||
|
|
outb(0xaa, port);
|
||
|
|
}
|
||
|
|
|
||
|
|
int sio1007_gpio_get_value(int port, int gpio)
|
||
|
|
{
|
||
|
|
int reg = GPIO0_DATA;
|
||
|
|
int val;
|
||
|
|
|
||
|
|
if (gpio < 0 || gpio > SIO1007_GPIO_NUM)
|
||
|
|
return -EINVAL;
|
||
|
|
if (gpio >= GPIO_NUM_PER_GROUP) {
|
||
|
|
reg = GPIO1_DATA;
|
||
|
|
gpio -= GPIO_NUM_PER_GROUP;
|
||
|
|
}
|
||
|
|
|
||
|
|
val = inb(port + reg);
|
||
|
|
if (val & (1 << gpio))
|
||
|
|
return 1;
|
||
|
|
else
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
void sio1007_gpio_set_value(int port, int gpio, int val)
|
||
|
|
{
|
||
|
|
int reg = GPIO0_DATA;
|
||
|
|
u8 data;
|
||
|
|
|
||
|
|
if (gpio < 0 || gpio > SIO1007_GPIO_NUM)
|
||
|
|
return;
|
||
|
|
if (gpio >= GPIO_NUM_PER_GROUP) {
|
||
|
|
reg = GPIO1_DATA;
|
||
|
|
gpio -= GPIO_NUM_PER_GROUP;
|
||
|
|
}
|
||
|
|
|
||
|
|
data = inb(port + reg);
|
||
|
|
data &= ~(1 << gpio);
|
||
|
|
data |= (val << gpio);
|
||
|
|
outb(data, port + reg);
|
||
|
|
}
|