129 lines
3.7 KiB
Plaintext
129 lines
3.7 KiB
Plaintext
|
Freescale MPC832XEMDS Board
|
||
|
|
-----------------------------------------
|
||
|
|
1. Board Switches and Jumpers
|
||
|
|
1.0 There are five Dual-In-Line Packages(DIP) Switches on MPC832XE SYS board
|
||
|
|
For some reason, the HW designers describe the switch settings
|
||
|
|
in terms of 0 and 1, and then map that to physical switches where
|
||
|
|
the label "On" refers to logic 0 and "Off" is logic 1.
|
||
|
|
|
||
|
|
Switch bits are numbered 1 through, like, 4 6 8 or 10, but the
|
||
|
|
bits may contribute to signals that are numbered based at 0,
|
||
|
|
and some of those signals may be high-bit-number-0 too. Heed
|
||
|
|
well the names and labels and do not get confused.
|
||
|
|
|
||
|
|
"Off" == 1
|
||
|
|
"On" == 0
|
||
|
|
|
||
|
|
SW3 is switch 18 as silk-screened onto the board.
|
||
|
|
SW4[8] is the bit labeled 8 on Switch 4.
|
||
|
|
SW5[1:6] refers to bits labeled 1 through 6 in order on switch 5.
|
||
|
|
SW6[7:1] refers to bits labeled 7 through 1 in order on switch 6.
|
||
|
|
SW7[1:8]= 0000_0001 refers to bits labeled 1 through 6 is set as "On"
|
||
|
|
and bits labeled 8 is set as "Off".
|
||
|
|
|
||
|
|
1.1 For the MPC832XEMDS PROTO Board
|
||
|
|
|
||
|
|
First, make sure the board default setting is consistent with the document
|
||
|
|
shipped with your board. Then apply the following setting:
|
||
|
|
SW3[1-8]= 0000_1000 (core PLL setting, core enable)
|
||
|
|
SW4[1-8]= 0001_0010 (Flash boot on local bus, system PLL setting)
|
||
|
|
SW5[1-8]= 0010_0110 (Boot from high end)
|
||
|
|
SW6[1-8]= 0011_0100 (Flash boot on 16 bit local bus)
|
||
|
|
SW7[1-8]= 1000_0011 (QE PLL setting)
|
||
|
|
|
||
|
|
ENET3/4 MII mode settings:
|
||
|
|
J1 1-2 (ETH3_TXER)
|
||
|
|
J2 2-3 (MII mode)
|
||
|
|
J3 2-3 (MII mode)
|
||
|
|
J4 2-3 (ADSL clockOscillator)
|
||
|
|
J5 1-2 (ETH4_TXER)
|
||
|
|
J6 2-3 (ClockOscillator)
|
||
|
|
JP1 removed (don't force PORESET)
|
||
|
|
JP2 mounted (ETH4/2 MII)
|
||
|
|
JP3 mounted (ETH3 MII)
|
||
|
|
JP4 mounted (HRCW from BCSR)
|
||
|
|
|
||
|
|
ENET3/4 RMII mode settings:
|
||
|
|
J1 1-2 (ETH3_TXER)
|
||
|
|
J2 1-2 (RMII mode)
|
||
|
|
J3 1-2 (RMII mode)
|
||
|
|
J4 2-3 (ADSL clockOscillator)
|
||
|
|
J5 1-2 (ETH4_TXER)
|
||
|
|
J6 2-3 (ClockOscillator)
|
||
|
|
JP1 removed (don't force PORESET)
|
||
|
|
JP2 removed (ETH4/2 RMII)
|
||
|
|
JP3 removed (ETH3 RMII)
|
||
|
|
JP4 removed (HRCW from FLASH)
|
||
|
|
|
||
|
|
on board Oscillator: 66M
|
||
|
|
|
||
|
|
|
||
|
|
2. Memory Map
|
||
|
|
|
||
|
|
2.1 The memory map should look pretty much like this:
|
||
|
|
|
||
|
|
0x0000_0000 0x7fff_ffff DDR 2G
|
||
|
|
0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M
|
||
|
|
0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M
|
||
|
|
0xc000_0000 0xdfff_ffff Empty 512M
|
||
|
|
0xe000_0000 0xe01f_ffff Int Mem Reg Space 2M
|
||
|
|
0xe020_0000 0xe02f_ffff Empty 1M
|
||
|
|
0xe030_0000 0xe03f_ffff PCI IO 1M
|
||
|
|
0xe040_0000 0xefff_ffff Empty 252M
|
||
|
|
0xf400_0000 0xf7ff_ffff Empty 64M
|
||
|
|
0xf800_0000 0xf800_7fff BCSR on CS1 32K
|
||
|
|
0xf800_8000 0xf800_ffff PIB CS2 32K
|
||
|
|
0xf801_0000 0xf801_7fff PIB CS3 32K
|
||
|
|
0xfe00_0000 0xfeff_ffff FLASH on CS0 16M
|
||
|
|
|
||
|
|
|
||
|
|
3. Definitions
|
||
|
|
|
||
|
|
3.1 Explanation of NEW definitions in:
|
||
|
|
|
||
|
|
include/configs/MPC832XEPB.h
|
||
|
|
|
||
|
|
CONFIG_MPC83xx MPC83xx family for MPC8349, MPC8360 and MPC832x
|
||
|
|
CONFIG_MPC832x MPC832x specific
|
||
|
|
CONFIG_MPC832XEMDS MPC832XEMDS board specific
|
||
|
|
|
||
|
|
4. Compilation
|
||
|
|
|
||
|
|
Assuming you're using BASH shell:
|
||
|
|
|
||
|
|
export CROSS_COMPILE=your-cross-compile-prefix
|
||
|
|
cd u-boot
|
||
|
|
make distclean
|
||
|
|
make MPC832XEMDS_config
|
||
|
|
make
|
||
|
|
|
||
|
|
MPC832x support PCI 33MHz and PCI 66MHz, to make U-Boot support PCI:
|
||
|
|
|
||
|
|
1)Make sure the DIP SW support PCI mode as described in Section 1.1.
|
||
|
|
|
||
|
|
2)To Make U-Boot image support PCI 33MHz, use
|
||
|
|
Make MPC832XEMDS_HOST_33_config
|
||
|
|
|
||
|
|
3)To Make U-Boot image support PCI 66MHz, use
|
||
|
|
Make MPC832XEMDS_HOST_66M_config
|
||
|
|
|
||
|
|
5. Downloading and Flashing Images
|
||
|
|
|
||
|
|
5.0 Download over network:
|
||
|
|
|
||
|
|
tftp 10000 u-boot.bin
|
||
|
|
|
||
|
|
5.1 Reflash U-Boot Image using U-Boot
|
||
|
|
|
||
|
|
tftp 20000 u-boot.bin
|
||
|
|
protect off fe000000 fe0fffff
|
||
|
|
erase fe000000 fe0fffff
|
||
|
|
cp.b 20000 fe000000 xxxx
|
||
|
|
|
||
|
|
You have to supply the correct byte count with 'xxxx' from the TFTP result log.
|
||
|
|
Maybe 3ffff will work too, that corresponds to the erased sectors.
|
||
|
|
|
||
|
|
|
||
|
|
6. Notes
|
||
|
|
1) The console baudrate for MPC832XEMDS is 115200bps.
|