112 lines
3.0 KiB
Plaintext
112 lines
3.0 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0
|
|
config FB_OMAP2_DSS_INIT
|
|
bool
|
|
|
|
config FB_OMAP2_DSS
|
|
tristate
|
|
select VIDEOMODE_HELPERS
|
|
select FB_OMAP2_DSS_INIT
|
|
select HDMI
|
|
|
|
config FB_OMAP2_DSS_DEBUG
|
|
bool "Debug support"
|
|
help
|
|
This enables printing of debug messages. Alternatively, debug messages
|
|
can also be enabled by setting CONFIG_DYNAMIC_DEBUG and then setting
|
|
appropriate flags in <debugfs>/dynamic_debug/control.
|
|
|
|
config FB_OMAP2_DSS_DEBUGFS
|
|
bool "Debugfs filesystem support"
|
|
depends on DEBUG_FS
|
|
help
|
|
This enables debugfs for OMAPDSS at <debugfs>/omapdss. This enables
|
|
querying about clock configuration and register configuration of dss,
|
|
dispc, dsi, hdmi and rfbi.
|
|
|
|
config FB_OMAP2_DSS_COLLECT_IRQ_STATS
|
|
bool "Collect DSS IRQ statistics"
|
|
depends on FB_OMAP2_DSS_DEBUGFS
|
|
help
|
|
Collect DSS IRQ statistics, printable via debugfs.
|
|
|
|
The statistics can be found from
|
|
<debugfs>/omapdss/dispc_irq for DISPC interrupts, and
|
|
<debugfs>/omapdss/dsi_irq for DSI interrupts.
|
|
|
|
config FB_OMAP2_DSS_DPI
|
|
bool "DPI support"
|
|
default y
|
|
help
|
|
DPI Interface. This is the Parallel Display Interface.
|
|
|
|
config FB_OMAP2_DSS_VENC
|
|
bool "VENC support"
|
|
default y
|
|
help
|
|
OMAP Video Encoder support for S-Video and composite TV-out.
|
|
|
|
config FB_OMAP2_DSS_HDMI_COMMON
|
|
bool
|
|
|
|
config FB_OMAP4_DSS_HDMI
|
|
bool "HDMI support for OMAP4"
|
|
default y
|
|
select FB_OMAP2_DSS_HDMI_COMMON
|
|
help
|
|
HDMI support for OMAP4 based SoCs.
|
|
|
|
config FB_OMAP5_DSS_HDMI
|
|
bool "HDMI support for OMAP5"
|
|
select FB_OMAP2_DSS_HDMI_COMMON
|
|
help
|
|
HDMI Interface for OMAP5 and similar cores. This adds the High
|
|
Definition Multimedia Interface. See http://www.hdmi.org/ for HDMI
|
|
specification.
|
|
|
|
config FB_OMAP2_DSS_SDI
|
|
bool "SDI support"
|
|
help
|
|
SDI (Serial Display Interface) support.
|
|
|
|
SDI is a high speed one-way display serial bus between the host
|
|
processor and a display.
|
|
|
|
config FB_OMAP2_DSS_DSI
|
|
bool "DSI support"
|
|
help
|
|
MIPI DSI (Display Serial Interface) support.
|
|
|
|
DSI is a high speed half-duplex serial interface between the host
|
|
processor and a peripheral, such as a display or a framebuffer chip.
|
|
|
|
See http://www.mipi.org/ for DSI specifications.
|
|
|
|
config FB_OMAP2_DSS_MIN_FCK_PER_PCK
|
|
int "Minimum FCK/PCK ratio (for scaling)"
|
|
range 0 32
|
|
default 0
|
|
help
|
|
This can be used to adjust the minimum FCK/PCK ratio.
|
|
|
|
With this you can make sure that DISPC FCK is at least
|
|
n x PCK. Video plane scaling requires higher FCK than
|
|
normally.
|
|
|
|
If this is set to 0, there's no extra constraint on the
|
|
DISPC FCK. However, the FCK will at minimum be
|
|
2xPCK (if active matrix) or 3xPCK (if passive matrix).
|
|
|
|
Max FCK is 173MHz, so this doesn't work if your PCK
|
|
is very high.
|
|
|
|
config FB_OMAP2_DSS_SLEEP_AFTER_VENC_RESET
|
|
bool "Sleep 20ms after VENC reset"
|
|
default y
|
|
help
|
|
There is a 20ms sleep after VENC reset which seemed to fix the
|
|
reset. The reason for the bug is unclear, and it's also unclear
|
|
on what platforms this happens.
|
|
|
|
This option enables the sleep, and is enabled by default. You can
|
|
disable the sleep if it doesn't cause problems on your platform.
|