138 lines
4.4 KiB
Plaintext
138 lines
4.4 KiB
Plaintext
RPMH RSC:
|
|
------------
|
|
|
|
Resource Power Manager Hardened (RPMH) is the mechanism for communicating with
|
|
the hardened resource accelerators on Qualcomm SoCs. Requests to the resources
|
|
can be written to the Trigger Command Set (TCS) registers and using a (addr,
|
|
val) pair and triggered. Messages in the TCS are then sent in sequence over an
|
|
internal bus.
|
|
|
|
The hardware block (Direct Resource Voter or DRV) is a part of the h/w entity
|
|
(Resource State Coordinator a.k.a RSC) that can handle multiple sleep and
|
|
active/wake resource requests. Multiple such DRVs can exist in a SoC and can
|
|
be written to from Linux. The structure of each DRV follows the same template
|
|
with a few variations that are captured by the properties here.
|
|
|
|
A TCS may be triggered from Linux or triggered by the F/W after all the CPUs
|
|
have powered off to facilitate idle power saving. TCS could be classified as -
|
|
|
|
ACTIVE /* Triggered by Linux */
|
|
SLEEP /* Triggered by F/W */
|
|
WAKE /* Triggered by F/W */
|
|
CONTROL /* Triggered by F/W */
|
|
|
|
The order in which they are described in the DT, should match the hardware
|
|
configuration.
|
|
|
|
Requests can be made for the state of a resource, when the subsystem is active
|
|
or idle. When all subsystems like Modem, GPU, CPU are idle, the resource state
|
|
will be an aggregate of the sleep votes from each of those subsystems. Clients
|
|
may request a sleep value for their shared resources in addition to the active
|
|
mode requests.
|
|
|
|
Properties:
|
|
|
|
- compatible:
|
|
Usage: required
|
|
Value type: <string>
|
|
Definition: Should be "qcom,rpmh-rsc".
|
|
|
|
- reg:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
Definition: The first register specifies the base address of the
|
|
DRV(s). The number of DRVs in the dependent on the RSC.
|
|
The tcs-offset specifies the start address of the
|
|
TCS in the DRVs.
|
|
|
|
- reg-names:
|
|
Usage: required
|
|
Value type: <string>
|
|
Definition: Maps the register specified in the reg property. Must be
|
|
"drv-0", "drv-1", "drv-2" etc and "tcs-offset". The
|
|
|
|
- interrupts:
|
|
Usage: required
|
|
Value type: <prop-encoded-interrupt>
|
|
Definition: The interrupt that trips when a message complete/response
|
|
is received for this DRV from the accelerators.
|
|
|
|
- qcom,drv-id:
|
|
Usage: required
|
|
Value type: <u32>
|
|
Definition: The id of the DRV in the RSC block that will be used by
|
|
this controller.
|
|
|
|
- qcom,tcs-config:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
Definition: The tuple defining the configuration of TCS.
|
|
Must have 2 cells which describe each TCS type.
|
|
<type number_of_tcs>.
|
|
The order of the TCS must match the hardware
|
|
configuration.
|
|
- Cell #1 (TCS Type): TCS types to be specified -
|
|
ACTIVE_TCS
|
|
SLEEP_TCS
|
|
WAKE_TCS
|
|
CONTROL_TCS
|
|
- Cell #2 (Number of TCS): <u32>
|
|
|
|
- label:
|
|
Usage: optional
|
|
Value type: <string>
|
|
Definition: Name for the RSC. The name would be used in trace logs.
|
|
|
|
Drivers that want to use the RSC to communicate with RPMH must specify their
|
|
bindings as child nodes of the RSC controllers they wish to communicate with.
|
|
|
|
Example 1:
|
|
|
|
For a TCS whose RSC base address is is 0x179C0000 and is at a DRV id of 2, the
|
|
register offsets for DRV2 start at 0D00, the register calculations are like
|
|
this -
|
|
DRV0: 0x179C0000
|
|
DRV2: 0x179C0000 + 0x10000 = 0x179D0000
|
|
DRV2: 0x179C0000 + 0x10000 * 2 = 0x179E0000
|
|
TCS-OFFSET: 0xD00
|
|
|
|
apps_rsc: rsc@179c0000 {
|
|
label = "apps_rsc";
|
|
compatible = "qcom,rpmh-rsc";
|
|
reg = <0x179c0000 0x10000>,
|
|
<0x179d0000 0x10000>,
|
|
<0x179e0000 0x10000>;
|
|
reg-names = "drv-0", "drv-1", "drv-2";
|
|
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
|
|
<GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
|
|
<GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
|
|
qcom,tcs-offset = <0xd00>;
|
|
qcom,drv-id = <2>;
|
|
qcom,tcs-config = <ACTIVE_TCS 2>,
|
|
<SLEEP_TCS 3>,
|
|
<WAKE_TCS 3>,
|
|
<CONTROL_TCS 1>;
|
|
};
|
|
|
|
Example 2:
|
|
|
|
For a TCS whose RSC base address is 0xAF20000 and is at DRV id of 0, the
|
|
register offsets for DRV0 start at 01C00, the register calculations are like
|
|
this -
|
|
DRV0: 0xAF20000
|
|
TCS-OFFSET: 0x1C00
|
|
|
|
disp_rsc: rsc@af20000 {
|
|
label = "disp_rsc";
|
|
compatible = "qcom,rpmh-rsc";
|
|
reg = <0xaf20000 0x10000>;
|
|
reg-names = "drv-0";
|
|
interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
|
|
qcom,tcs-offset = <0x1c00>;
|
|
qcom,drv-id = <0>;
|
|
qcom,tcs-config = <ACTIVE_TCS 0>,
|
|
<SLEEP_TCS 1>,
|
|
<WAKE_TCS 1>,
|
|
<CONTROL_TCS 0>;
|
|
};
|