96 lines
3.3 KiB
Plaintext
96 lines
3.3 KiB
Plaintext
* UART (Universal Asynchronous Receiver/Transmitter)
|
|
|
|
Required properties:
|
|
- compatible : one of:
|
|
- "ns8250"
|
|
- "ns16450"
|
|
- "ns16550a"
|
|
- "ns16550"
|
|
- "ns16750"
|
|
- "ns16850"
|
|
- For Tegra20, must contain "nvidia,tegra20-uart"
|
|
- For other Tegra, must contain '"nvidia,<chip>-uart",
|
|
"nvidia,tegra20-uart"' where <chip> is tegra30, tegra114, tegra124,
|
|
tegra132, or tegra210.
|
|
- "nxp,lpc3220-uart"
|
|
- "ralink,rt2880-uart"
|
|
- For MediaTek BTIF, must contain '"mediatek,<chip>-btif",
|
|
"mediatek,mtk-btif"' where <chip> is mt7622, mt7623.
|
|
- "altr,16550-FIFO32"
|
|
- "altr,16550-FIFO64"
|
|
- "altr,16550-FIFO128"
|
|
- "fsl,16550-FIFO64"
|
|
- "fsl,ns16550"
|
|
- "intel,xscale-uart"
|
|
- "ti,da830-uart"
|
|
- "aspeed,ast2400-vuart"
|
|
- "aspeed,ast2500-vuart"
|
|
- "nuvoton,npcm750-uart"
|
|
- "serial" if the port type is unknown.
|
|
- reg : offset and length of the register set for the device.
|
|
- interrupts : should contain uart interrupt.
|
|
- clock-frequency : the input clock frequency for the UART
|
|
or
|
|
clocks phandle to refer to the clk used as per Documentation/devicetree
|
|
/bindings/clock/clock-bindings.txt
|
|
|
|
Optional properties:
|
|
- current-speed : the current active speed of the UART.
|
|
- reg-offset : offset to apply to the mapbase from the start of the registers.
|
|
- reg-shift : quantity to shift the register offsets by.
|
|
- reg-io-width : the size (in bytes) of the IO accesses that should be
|
|
performed on the device. There are some systems that require 32-bit
|
|
accesses to the UART (e.g. TI davinci).
|
|
- used-by-rtas : set to indicate that the port is in use by the OpenFirmware
|
|
RTAS and should not be registered.
|
|
- no-loopback-test: set to indicate that the port does not implements loopback
|
|
test mode
|
|
- fifo-size: the fifo size of the UART.
|
|
- auto-flow-control: one way to enable automatic flow control support. The
|
|
driver is allowed to detect support for the capability even without this
|
|
property.
|
|
- tx-threshold: Specify the TX FIFO low water indication for parts with
|
|
programmable TX FIFO thresholds.
|
|
- resets : phandle + reset specifier pairs
|
|
- overrun-throttle-ms : how long to pause uart rx when input overrun is encountered.
|
|
- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD
|
|
line respectively. It will use specified GPIO instead of the peripheral
|
|
function pin for the UART feature. If unsure, don't specify this property.
|
|
|
|
Note:
|
|
* fsl,ns16550:
|
|
------------
|
|
Freescale DUART is very similar to the PC16552D (and to a
|
|
pair of NS16550A), albeit with some nonstandard behavior such as
|
|
erratum A-004737 (relating to incorrect BRK handling).
|
|
|
|
Represents a single port that is compatible with the DUART found
|
|
on many Freescale chips (examples include mpc8349, mpc8548,
|
|
mpc8641d, p4080 and ls2085a).
|
|
|
|
Example:
|
|
|
|
uart@80230000 {
|
|
compatible = "ns8250";
|
|
reg = <0x80230000 0x100>;
|
|
clock-frequency = <3686400>;
|
|
interrupts = <10>;
|
|
reg-shift = <2>;
|
|
};
|
|
|
|
Example for OMAP UART using GPIO-based modem control signals:
|
|
|
|
uart4: serial@49042000 {
|
|
compatible = "ti,omap3-uart";
|
|
reg = <0x49042000 0x400>;
|
|
interrupts = <80>;
|
|
ti,hwmods = "uart4";
|
|
clock-frequency = <48000000>;
|
|
cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>;
|
|
rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
|
|
dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
|
|
dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
|
|
dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
|
|
rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
|
|
};
|