89 lines
2.4 KiB
Plaintext
89 lines
2.4 KiB
Plaintext
* Dialog Semiconductor SLG51000 Voltage Regulator
|
|
|
|
Required properties:
|
|
- compatible : Should be "dlg,slg51000" for SLG51000
|
|
- reg : Specifies the I2C slave address.
|
|
- xxx-supply: Input voltage supply regulator for ldo3 to ldo7.
|
|
These entries are required if regulators are enabled for a device.
|
|
An absence of these properties can cause the regulator registration to fail.
|
|
If some of input supply is powered through battery or always-on supply then
|
|
also it is required to have these parameters with proper node handle of always
|
|
on power supply.
|
|
vin3-supply: Input supply for ldo3
|
|
vin4-supply: Input supply for ldo4
|
|
vin5-supply: Input supply for ldo5
|
|
vin6-supply: Input supply for ldo6
|
|
vin7-supply: Input supply for ldo7
|
|
|
|
Optional properties:
|
|
- interrupt-parent : Specifies the reference to the interrupt controller.
|
|
- interrupts : IRQ line information.
|
|
- dlg,cs-gpios : Specify a valid GPIO for chip select
|
|
|
|
Sub-nodes:
|
|
- regulators : This node defines the settings for the regulators.
|
|
The content of the sub-node is defined by the standard binding
|
|
for regulators; see regulator.txt.
|
|
|
|
The SLG51000 regulators are bound using their names listed below:
|
|
ldo1
|
|
ldo2
|
|
ldo3
|
|
ldo4
|
|
ldo5
|
|
ldo6
|
|
ldo7
|
|
|
|
Optional properties for regulators:
|
|
- enable-gpios : Specify a valid GPIO for platform control of the regulator.
|
|
|
|
Example:
|
|
pmic: slg51000@75 {
|
|
compatible = "dlg,slg51000";
|
|
reg = <0x75>;
|
|
|
|
regulators {
|
|
ldo1 {
|
|
regulator-name = "ldo1";
|
|
regulator-min-microvolt = <2400000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
ldo2 {
|
|
regulator-name = "ldo2";
|
|
regulator-min-microvolt = <2400000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
ldo3 {
|
|
regulator-name = "ldo3";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <3750000>;
|
|
};
|
|
|
|
ldo4 {
|
|
regulator-name = "ldo4";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <3750000>;
|
|
};
|
|
|
|
ldo5 {
|
|
regulator-name = "ldo5";
|
|
regulator-min-microvolt = <500000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
};
|
|
|
|
ldo6 {
|
|
regulator-name = "ldo6";
|
|
regulator-min-microvolt = <500000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
};
|
|
|
|
ldo7 {
|
|
regulator-name = "ldo7";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <3750000>;
|
|
};
|
|
};
|
|
};
|