51 lines
1.9 KiB
Plaintext
51 lines
1.9 KiB
Plaintext
* Axis ARTPEC-6 PCIe interface
|
|
|
|
This PCIe host controller is based on the Synopsys DesignWare PCIe IP
|
|
and thus inherits all the common properties defined in designware-pcie.txt.
|
|
|
|
Required properties:
|
|
- compatible: "axis,artpec6-pcie", "snps,dw-pcie" for ARTPEC-6 in RC mode;
|
|
"axis,artpec6-pcie-ep", "snps,dw-pcie" for ARTPEC-6 in EP mode;
|
|
"axis,artpec7-pcie", "snps,dw-pcie" for ARTPEC-7 in RC mode;
|
|
"axis,artpec7-pcie-ep", "snps,dw-pcie" for ARTPEC-7 in EP mode;
|
|
- reg: base addresses and lengths of the PCIe controller (DBI),
|
|
the PHY controller, and configuration address space.
|
|
- reg-names: Must include the following entries:
|
|
- "dbi"
|
|
- "phy"
|
|
- "config"
|
|
- interrupts: A list of interrupt outputs of the controller. Must contain an
|
|
entry for each entry in the interrupt-names property.
|
|
- interrupt-names: Must include the following entries:
|
|
- "msi": The interrupt that is asserted when an MSI is received
|
|
- axis,syscon-pcie: A phandle pointing to the ARTPEC-6 system controller,
|
|
used to enable and control the Synopsys IP.
|
|
|
|
Example:
|
|
|
|
pcie@f8050000 {
|
|
compatible = "axis,artpec6-pcie", "snps,dw-pcie";
|
|
reg = <0xf8050000 0x2000
|
|
0xf8040000 0x1000
|
|
0xc0000000 0x2000>;
|
|
reg-names = "dbi", "phy", "config";
|
|
#address-cells = <3>;
|
|
#size-cells = <2>;
|
|
device_type = "pci";
|
|
/* downstream I/O */
|
|
ranges = <0x81000000 0 0 0xc0002000 0 0x00010000
|
|
/* non-prefetchable memory */
|
|
0x82000000 0 0xc0012000 0xc0012000 0 0x1ffee000>;
|
|
num-lanes = <2>;
|
|
bus-range = <0x00 0xff>;
|
|
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "msi";
|
|
#interrupt-cells = <1>;
|
|
interrupt-map-mask = <0 0 0 0x7>;
|
|
interrupt-map = <0 0 0 1 &intc GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
|
|
<0 0 0 2 &intc GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
|
|
<0 0 0 3 &intc GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
|
|
<0 0 0 4 &intc GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
|
|
axis,syscon-pcie = <&syscon>;
|
|
};
|