77 lines
2.8 KiB
Plaintext
77 lines
2.8 KiB
Plaintext
Cirrus Logic Arizona class audio SoCs
|
|
|
|
These devices are audio SoCs with extensive digital capabilities and a range
|
|
of analogue I/O.
|
|
|
|
This document lists Extcon specific bindings, see the primary binding document:
|
|
../mfd/arizona.txt
|
|
|
|
Optional properties:
|
|
|
|
- wlf,hpdet-channel : Headphone detection channel.
|
|
ARIZONA_ACCDET_MODE_HPL or 1 - Headphone detect mode is set to HPDETL
|
|
ARIZONA_ACCDET_MODE_HPR or 2 - Headphone detect mode is set to HPDETR
|
|
If this node is not mentioned or if the value is unknown, then
|
|
headphone detection mode is set to HPDETL.
|
|
|
|
- wlf,use-jd2 : Use the additional JD input along with JD1 for dual pin jack
|
|
detection.
|
|
- wlf,use-jd2-nopull : Internal pull on JD2 is disabled when used for
|
|
jack detection.
|
|
- wlf,jd-invert : Invert the polarity of the jack detection switch
|
|
|
|
- wlf,micd-software-compare : Use a software comparison to determine mic
|
|
presence
|
|
- wlf,micd-detect-debounce : Additional software microphone detection
|
|
debounce specified in milliseconds.
|
|
- wlf,micd-pol-gpio : GPIO specifier for the GPIO controlling the headset
|
|
polarity if one exists.
|
|
- wlf,micd-bias-start-time : Time allowed for MICBIAS to startup prior to
|
|
performing microphone detection, specified as per the ARIZONA_MICD_TIME_XXX
|
|
defines.
|
|
- wlf,micd-rate : Delay between successive microphone detection measurements,
|
|
specified as per the ARIZONA_MICD_TIME_XXX defines.
|
|
- wlf,micd-dbtime : Microphone detection hardware debounces specified as the
|
|
number of measurements to take, valid values being 2 and 4.
|
|
- wlf,micd-timeout-ms : Timeout for microphone detection, specified in
|
|
milliseconds.
|
|
- wlf,micd-force-micbias : Force MICBIAS continuously on during microphone
|
|
detection.
|
|
- wlf,micd-configs : Headset polarity configurations (generally used for
|
|
detection of CTIA / OMTP headsets), the field can be of variable length
|
|
but should always be a multiple of 3 cells long, each three cell group
|
|
represents one polarity configuration.
|
|
The first cell defines the accessory detection pin, zero will use MICDET1
|
|
and all other values will use MICDET2.
|
|
The second cell represents the MICBIAS to be used.
|
|
The third cell represents the value of the micd-pol-gpio pin.
|
|
|
|
- wlf,gpsw : Settings for the general purpose switch, set as one of the
|
|
ARIZONA_GPSW_XXX defines.
|
|
|
|
Example:
|
|
|
|
codec: wm8280@0 {
|
|
compatible = "wlf,wm8280";
|
|
reg = <0>;
|
|
...
|
|
|
|
wlf,use-jd2;
|
|
wlf,use-jd2-nopull;
|
|
wlf,jd-invert;
|
|
|
|
wlf,micd-software-compare;
|
|
wlf,micd-detect-debounce = <0>;
|
|
wlf,micd-pol-gpio = <&codec 2 0>;
|
|
wlf,micd-rate = <ARIZONA_MICD_TIME_8MS>;
|
|
wlf,micd-dbtime = <4>;
|
|
wlf,micd-timeout-ms = <100>;
|
|
wlf,micd-force-micbias;
|
|
wlf,micd-configs = <
|
|
0 1 0 /* MICDET1 MICBIAS1 GPIO=low */
|
|
1 2 1 /* MICDET2 MICBIAS2 GPIO=high */
|
|
>;
|
|
|
|
wlf,gpsw = <ARIZONA_GPSW_OPEN>;
|
|
};
|