247 lines
7.6 KiB
Plaintext
247 lines
7.6 KiB
Plaintext
Qualcomm Technologies Inc. adreno/snapdragon DSI output
|
|
|
|
DSI Controller:
|
|
Required properties:
|
|
- compatible:
|
|
* "qcom,mdss-dsi-ctrl"
|
|
- reg: Physical base address and length of the registers of controller
|
|
- reg-names: The names of register regions. The following regions are required:
|
|
* "dsi_ctrl"
|
|
- interrupts: The interrupt signal from the DSI block.
|
|
- power-domains: Should be <&mmcc MDSS_GDSC>.
|
|
- clocks: Phandles to device clocks.
|
|
- clock-names: the following clocks are required:
|
|
* "mdp_core"
|
|
* "iface"
|
|
* "bus"
|
|
* "core_mmss"
|
|
* "byte"
|
|
* "pixel"
|
|
* "core"
|
|
For DSIv2, we need an additional clock:
|
|
* "src"
|
|
For DSI6G v2.0 onwards, we need also need the clock:
|
|
* "byte_intf"
|
|
- assigned-clocks: Parents of "byte" and "pixel" for the given platform.
|
|
- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided
|
|
by a DSI PHY block. See [1] for details on clock bindings.
|
|
- vdd-supply: phandle to vdd regulator device node
|
|
- vddio-supply: phandle to vdd-io regulator device node
|
|
- vdda-supply: phandle to vdda regulator device node
|
|
- phys: phandle to DSI PHY device node
|
|
- phy-names: the name of the corresponding PHY device
|
|
- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2)
|
|
- ports: Contains 2 DSI controller ports as child nodes. Each port contains
|
|
an endpoint subnode as defined in [2] and [3].
|
|
|
|
Optional properties:
|
|
- panel@0: Node of panel connected to this DSI controller.
|
|
See files in [4] for each supported panel.
|
|
- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
|
|
driving a panel which needs 2 DSI links.
|
|
- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
|
|
the master link of the 2-DSI panel.
|
|
- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
|
|
driving a 2-DSI panel whose 2 links need receive command simultaneously.
|
|
- pinctrl-names: the pin control state names; should contain "default"
|
|
- pinctrl-0: the default pinctrl state (active)
|
|
- pinctrl-n: the "sleep" pinctrl state
|
|
- ports: contains DSI controller input and output ports as children, each
|
|
containing one endpoint subnode.
|
|
|
|
DSI Endpoint properties:
|
|
- remote-endpoint: For port@0, set to phandle of the connected panel/bridge's
|
|
input endpoint. For port@1, set to the MDP interface output. See [2] for
|
|
device graph info.
|
|
|
|
- data-lanes: this describes how the physical DSI data lanes are mapped
|
|
to the logical lanes on the given platform. The value contained in
|
|
index n describes what physical lane is mapped to the logical lane n
|
|
(DATAn, where n lies between 0 and 3). The clock lane position is fixed
|
|
and can't be changed. Hence, they aren't a part of the DT bindings. See
|
|
[3] for more info on the data-lanes property.
|
|
|
|
For example:
|
|
|
|
data-lanes = <3 0 1 2>;
|
|
|
|
The above mapping describes that the logical data lane DATA0 is mapped to
|
|
the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2
|
|
to phys DATA1 and logic DATA3 to phys DATA2.
|
|
|
|
There are only a limited number of physical to logical mappings possible:
|
|
<0 1 2 3>
|
|
<1 2 3 0>
|
|
<2 3 0 1>
|
|
<3 0 1 2>
|
|
<0 3 2 1>
|
|
<1 0 3 2>
|
|
<2 1 0 3>
|
|
<3 2 1 0>
|
|
|
|
DSI PHY:
|
|
Required properties:
|
|
- compatible: Could be the following
|
|
* "qcom,dsi-phy-28nm-hpm"
|
|
* "qcom,dsi-phy-28nm-lp"
|
|
* "qcom,dsi-phy-20nm"
|
|
* "qcom,dsi-phy-28nm-8960"
|
|
* "qcom,dsi-phy-14nm"
|
|
* "qcom,dsi-phy-10nm"
|
|
* "qcom,dsi-phy-10nm-8998"
|
|
- reg: Physical base address and length of the registers of PLL, PHY. Some
|
|
revisions require the PHY regulator base address, whereas others require the
|
|
PHY lane base address. See below for each PHY revision.
|
|
- reg-names: The names of register regions. The following regions are required:
|
|
For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY:
|
|
* "dsi_pll"
|
|
* "dsi_phy"
|
|
* "dsi_phy_regulator"
|
|
For DSI 14nm and 10nm PHYs:
|
|
* "dsi_pll"
|
|
* "dsi_phy"
|
|
* "dsi_phy_lane"
|
|
- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating
|
|
2 clocks: A byte clock (index 0), and a pixel clock (index 1).
|
|
- power-domains: Should be <&mmcc MDSS_GDSC>.
|
|
- clocks: Phandles to device clocks. See [1] for details on clock bindings.
|
|
- clock-names: the following clocks are required:
|
|
* "iface"
|
|
* "ref" (only required for new DTS files/entries)
|
|
For 28nm HPM/LP, 28nm 8960 PHYs:
|
|
- vddio-supply: phandle to vdd-io regulator device node
|
|
For 20nm PHY:
|
|
- vddio-supply: phandle to vdd-io regulator device node
|
|
- vcca-supply: phandle to vcca regulator device node
|
|
For 14nm PHY:
|
|
- vcca-supply: phandle to vcca regulator device node
|
|
For 10nm PHY:
|
|
- vdds-supply: phandle to vdds regulator device node
|
|
|
|
Optional properties:
|
|
- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
|
|
regulator is wanted.
|
|
- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode
|
|
panels in microseconds. Driver uses this number to adjust
|
|
the clock rate according to the expected transfer time.
|
|
Increasing this value would slow down the mdp processing
|
|
and can result in slower performance.
|
|
Decreasing this value can speed up the mdp processing,
|
|
but this can also impact power consumption.
|
|
As a rule this time should not be higher than the time
|
|
that would be expected with the processing at the
|
|
dsi link rate since anyways this would be the maximum
|
|
transfer time that could be achieved.
|
|
If ping pong split is enabled, this time should not be higher
|
|
than two times the dsi link rate time.
|
|
If the property is not specified, then the default value is 14000 us.
|
|
|
|
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
|
|
[2] Documentation/devicetree/bindings/graph.txt
|
|
[3] Documentation/devicetree/bindings/media/video-interfaces.txt
|
|
[4] Documentation/devicetree/bindings/display/panel/
|
|
|
|
Example:
|
|
dsi0: dsi@fd922800 {
|
|
compatible = "qcom,mdss-dsi-ctrl";
|
|
qcom,dsi-host-index = <0>;
|
|
interrupt-parent = <&mdp>;
|
|
interrupts = <4 0>;
|
|
reg-names = "dsi_ctrl";
|
|
reg = <0xfd922800 0x200>;
|
|
power-domains = <&mmcc MDSS_GDSC>;
|
|
clock-names =
|
|
"bus",
|
|
"byte",
|
|
"core",
|
|
"core_mmss",
|
|
"iface",
|
|
"mdp_core",
|
|
"pixel";
|
|
clocks =
|
|
<&mmcc MDSS_AXI_CLK>,
|
|
<&mmcc MDSS_BYTE0_CLK>,
|
|
<&mmcc MDSS_ESC0_CLK>,
|
|
<&mmcc MMSS_MISC_AHB_CLK>,
|
|
<&mmcc MDSS_AHB_CLK>,
|
|
<&mmcc MDSS_MDP_CLK>,
|
|
<&mmcc MDSS_PCLK0_CLK>;
|
|
|
|
assigned-clocks =
|
|
<&mmcc BYTE0_CLK_SRC>,
|
|
<&mmcc PCLK0_CLK_SRC>;
|
|
assigned-clock-parents =
|
|
<&dsi_phy0 0>,
|
|
<&dsi_phy0 1>;
|
|
|
|
vdda-supply = <&pma8084_l2>;
|
|
vdd-supply = <&pma8084_l22>;
|
|
vddio-supply = <&pma8084_l12>;
|
|
|
|
phys = <&dsi_phy0>;
|
|
phy-names ="dsi-phy";
|
|
|
|
qcom,dual-dsi-mode;
|
|
qcom,master-dsi;
|
|
qcom,sync-dual-dsi;
|
|
|
|
qcom,mdss-mdp-transfer-time-us = <12000>;
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&dsi_active>;
|
|
pinctrl-1 = <&dsi_suspend>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
dsi0_in: endpoint {
|
|
remote-endpoint = <&mdp_intf1_out>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
dsi0_out: endpoint {
|
|
remote-endpoint = <&panel_in>;
|
|
data-lanes = <0 1 2 3>;
|
|
};
|
|
};
|
|
};
|
|
|
|
panel: panel@0 {
|
|
compatible = "sharp,lq101r1sx01";
|
|
reg = <0>;
|
|
link2 = <&secondary>;
|
|
|
|
power-supply = <...>;
|
|
backlight = <...>;
|
|
|
|
port {
|
|
panel_in: endpoint {
|
|
remote-endpoint = <&dsi0_out>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
dsi_phy0: dsi-phy@fd922a00 {
|
|
compatible = "qcom,dsi-phy-28nm-hpm";
|
|
qcom,dsi-phy-index = <0>;
|
|
reg-names =
|
|
"dsi_pll",
|
|
"dsi_phy",
|
|
"dsi_phy_regulator";
|
|
reg = <0xfd922a00 0xd4>,
|
|
<0xfd922b00 0x2b0>,
|
|
<0xfd922d80 0x7b>;
|
|
clock-names = "iface";
|
|
clocks = <&mmcc MDSS_AHB_CLK>;
|
|
#clock-cells = <1>;
|
|
vddio-supply = <&pma8084_l12>;
|
|
|
|
qcom,dsi-phy-regulator-ldo-mode;
|
|
};
|