75 lines
2.5 KiB
Plaintext
75 lines
2.5 KiB
Plaintext
sii902x HDMI bridge bindings
|
|
|
|
Required properties:
|
|
- compatible: "sil,sii9022"
|
|
- reg: i2c address of the bridge
|
|
|
|
Optional properties:
|
|
- interrupts: describe the interrupt line used to inform the host
|
|
about hotplug events.
|
|
- reset-gpios: OF device-tree gpio specification for RST_N pin.
|
|
|
|
HDMI audio properties:
|
|
- #sound-dai-cells: <0> or <1>. <0> if only i2s or spdif pin
|
|
is wired, <1> if the both are wired. HDMI audio is
|
|
configured only if this property is found.
|
|
- sil,i2s-data-lanes: Array of up to 4 integers with values of 0-3
|
|
Each integer indicates which i2s pin is connected to which
|
|
audio fifo. The first integer selects i2s audio pin for the
|
|
first audio fifo#0 (HDMI channels 1&2), second for fifo#1
|
|
(HDMI channels 3&4), and so on. There is 4 fifos and 4 i2s
|
|
pins (SD0 - SD3). Any i2s pin can be connected to any fifo,
|
|
but there can be no gaps. E.g. an i2s pin must be mapped to
|
|
fifo#0 and fifo#1 before mapping a channel to fifo#2. Default
|
|
value is <0>, describing SD0 pin beiging routed to hdmi audio
|
|
fifo #0.
|
|
- clocks: phandle and clock specifier for each clock listed in
|
|
the clock-names property
|
|
- clock-names: "mclk"
|
|
Describes SII902x MCLK input. MCLK can be used to produce
|
|
HDMI audio CTS values. This property follows
|
|
Documentation/devicetree/bindings/clock/clock-bindings.txt
|
|
consumer binding.
|
|
|
|
If HDMI audio is configured the sii902x device becomes an I2S
|
|
and/or spdif audio codec component (e.g a digital audio sink),
|
|
that can be used in configuring a full audio devices with
|
|
simple-card or audio-graph-card binding. See their binding
|
|
documents on how to describe the way the sii902x device is
|
|
connected to the rest of the audio system:
|
|
Documentation/devicetree/bindings/sound/simple-card.txt
|
|
Documentation/devicetree/bindings/sound/audio-graph-card.txt
|
|
Note: In case of the audio-graph-card binding the used port
|
|
index should be 3.
|
|
|
|
Optional subnodes:
|
|
- video input: this subnode can contain a video input port node
|
|
to connect the bridge to a display controller output (See this
|
|
documentation [1]).
|
|
|
|
[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
|
|
|
|
Example:
|
|
hdmi-bridge@39 {
|
|
compatible = "sil,sii9022";
|
|
reg = <0x39>;
|
|
reset-gpios = <&pioA 1 0>;
|
|
|
|
#sound-dai-cells = <0>;
|
|
sil,i2s-data-lanes = < 0 1 2 >;
|
|
clocks = <&mclk>;
|
|
clock-names = "mclk";
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
bridge_in: endpoint {
|
|
remote-endpoint = <&dc_out>;
|
|
};
|
|
};
|
|
};
|
|
};
|