53 lines
2.7 KiB
ReStructuredText
53 lines
2.7 KiB
ReStructuredText
=====================================================
|
||
Freescale i.MX8 DDR Performance Monitoring Unit (PMU)
|
||
=====================================================
|
||
|
||
There are no performance counters inside the DRAM controller, so performance
|
||
signals are brought out to the edge of the controller where a set of 4 x 32 bit
|
||
counters is implemented. This is controlled by the CSV modes programed in counter
|
||
control register which causes a large number of PERF signals to be generated.
|
||
|
||
Selection of the value for each counter is done via the config registers. There
|
||
is one register for each counter. Counter 0 is special in that it always counts
|
||
“time” and when expired causes a lock on itself and the other counters and an
|
||
interrupt is raised. If any other counter overflows, it continues counting, and
|
||
no interrupt is raised.
|
||
|
||
The "format" directory describes format of the config (event ID) and config1
|
||
(AXI filtering) fields of the perf_event_attr structure, see /sys/bus/event_source/
|
||
devices/imx8_ddr0/format/. The "events" directory describes the events types
|
||
hardware supported that can be used with perf tool, see /sys/bus/event_source/
|
||
devices/imx8_ddr0/events/.
|
||
e.g.::
|
||
perf stat -a -e imx8_ddr0/cycles/ cmd
|
||
perf stat -a -e imx8_ddr0/read/,imx8_ddr0/write/ cmd
|
||
|
||
AXI filtering is only used by CSV modes 0x41 (axid-read) and 0x42 (axid-write)
|
||
to count reading or writing matches filter setting. Filter setting is various
|
||
from different DRAM controller implementations, which is distinguished by quirks
|
||
in the driver.
|
||
|
||
* With DDR_CAP_AXI_ID_FILTER quirk.
|
||
Filter is defined with two configuration parts:
|
||
--AXI_ID defines AxID matching value.
|
||
--AXI_MASKING defines which bits of AxID are meaningful for the matching.
|
||
0：corresponding bit is masked.
|
||
1: corresponding bit is not masked, i.e. used to do the matching.
|
||
|
||
AXI_ID and AXI_MASKING are mapped on DPCR1 register in performance counter.
|
||
When non-masked bits are matching corresponding AXI_ID bits then counter is
|
||
incremented. Perf counter is incremented if
|
||
AxID && AXI_MASKING == AXI_ID && AXI_MASKING
|
||
|
||
This filter doesn't support filter different AXI ID for axid-read and axid-write
|
||
event at the same time as this filter is shared between counters.
|
||
e.g.::
|
||
perf stat -a -e imx8_ddr0/axid-read,axi_mask=0xMMMM,axi_id=0xDDDD/ cmd
|
||
perf stat -a -e imx8_ddr0/axid-write,axi_mask=0xMMMM,axi_id=0xDDDD/ cmd
|
||
|
||
NOTE: axi_mask is inverted in userspace(i.e. set bits are bits to mask), and
|
||
it will be reverted in driver automatically. so that the user can just specify
|
||
axi_id to monitor a specific id, rather than having to specify axi_mask.
|
||
e.g.::
|
||
perf stat -a -e imx8_ddr0/axid-read,axi_id=0x12/ cmd, which will monitor ARID=0x12
|