62 lines
1.9 KiB
Plaintext
62 lines
1.9 KiB
Plaintext
|
TI BQ24190 Li-Ion Battery Charger
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: contains one of the following:
|
||
|
|
* "ti,bq24190"
|
||
|
|
* "ti,bq24192"
|
||
|
|
* "ti,bq24192i"
|
||
|
|
* "ti,bq24196"
|
||
|
|
- reg: integer, I2C address of the charger.
|
||
|
|
- interrupts[-extended]: configuration for charger INT pin.
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- monitored-battery: phandle of battery characteristics devicetree node
|
||
|
|
The charger uses the following battery properties:
|
||
|
|
+ precharge-current-microamp: maximum charge current during precharge
|
||
|
|
phase (typically 20% of battery capacity).
|
||
|
|
+ charge-term-current-microamp: a charge cycle terminates when the
|
||
|
|
battery voltage is above recharge threshold, and the current is below
|
||
|
|
this setting (typically 10% of battery capacity).
|
||
|
|
See also Documentation/devicetree/bindings/power/supply/battery.txt
|
||
|
|
- ti,system-minimum-microvolt: when power is connected and the battery is below
|
||
|
|
minimum system voltage, the system will be regulated above this setting.
|
||
|
|
|
||
|
|
child nodes:
|
||
|
|
- usb-otg-vbus:
|
||
|
|
Usage: optional
|
||
|
|
Description: Regulator that is used to control the VBUS voltage direction for
|
||
|
|
either USB host mode or for charging on the OTG port.
|
||
|
|
|
||
|
|
Notes:
|
||
|
|
- Some circuit boards wire the chip's "OTG" pin high (enabling 500mA default
|
||
|
|
charge current on USB SDP ports, among other features). To simulate this on
|
||
|
|
boards that wire the pin to a GPIO, set a gpio-hog.
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
bat: battery {
|
||
|
|
compatible = "simple-battery";
|
||
|
|
precharge-current-microamp = <256000>;
|
||
|
|
charge-term-current-microamp = <128000>;
|
||
|
|
// etc.
|
||
|
|
};
|
||
|
|
|
||
|
|
bq24190: charger@6a {
|
||
|
|
compatible = "ti,bq24190";
|
||
|
|
reg = <0x6a>;
|
||
|
|
interrupts-extended = <&gpiochip 10 IRQ_TYPE_EDGE_FALLING>;
|
||
|
|
monitored-battery = <&bat>;
|
||
|
|
ti,system-minimum-microvolt = <3200000>;
|
||
|
|
|
||
|
|
usb_otg_vbus: usb-otg-vbus { };
|
||
|
|
};
|
||
|
|
|
||
|
|
&twl_gpio {
|
||
|
|
otg {
|
||
|
|
gpio-hog;
|
||
|
|
gpios = <6 0>;
|
||
|
|
output-high;
|
||
|
|
line-name = "otg-gpio";
|
||
|
|
};
|
||
|
|
};
|