103 lines
4.0 KiB
Plaintext
103 lines
4.0 KiB
Plaintext
|
TI PCI Controllers
|
||
|
|
|
||
|
|
PCIe DesignWare Controller
|
||
|
|
- compatible: Should be "ti,dra7-pcie" for RC (deprecated)
|
||
|
|
Should be "ti,dra7-pcie-ep" for EP (deprecated)
|
||
|
|
Should be "ti,dra746-pcie-rc" for dra74x/dra76 in RC mode
|
||
|
|
Should be "ti,dra746-pcie-ep" for dra74x/dra76 in EP mode
|
||
|
|
Should be "ti,dra726-pcie-rc" for dra72x in RC mode
|
||
|
|
Should be "ti,dra726-pcie-ep" for dra72x in EP mode
|
||
|
|
- phys : list of PHY specifiers (used by generic PHY framework)
|
||
|
|
- phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
|
||
|
|
number of PHYs as specified in *phys* property.
|
||
|
|
- ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
|
||
|
|
where <X> is the instance number of the pcie from the HW spec.
|
||
|
|
- num-lanes as specified in ../designware-pcie.txt
|
||
|
|
- ti,syscon-lane-sel : phandle/offset pair. Phandle to the system control
|
||
|
|
module and the register offset to specify lane
|
||
|
|
selection.
|
||
|
|
|
||
|
|
HOST MODE
|
||
|
|
=========
|
||
|
|
- reg : Two register ranges as listed in the reg-names property
|
||
|
|
- reg-names : The first entry must be "ti-conf" for the TI-specific registers
|
||
|
|
The second entry must be "rc-dbics" for the DesignWare PCIe
|
||
|
|
registers
|
||
|
|
The third entry must be "config" for the PCIe configuration space
|
||
|
|
- interrupts : Two interrupt entries must be specified. The first one is for
|
||
|
|
main interrupt line and the second for MSI interrupt line.
|
||
|
|
- #address-cells,
|
||
|
|
#size-cells,
|
||
|
|
#interrupt-cells,
|
||
|
|
device_type,
|
||
|
|
ranges,
|
||
|
|
interrupt-map-mask,
|
||
|
|
interrupt-map : as specified in ../designware-pcie.txt
|
||
|
|
- ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument
|
||
|
|
should contain the register offset within syscon
|
||
|
|
and the 2nd argument should contain the bit field
|
||
|
|
for setting the bit to enable unaligned
|
||
|
|
access.
|
||
|
|
|
||
|
|
DEVICE MODE
|
||
|
|
===========
|
||
|
|
- reg : Four register ranges as listed in the reg-names property
|
||
|
|
- reg-names : "ti-conf" for the TI-specific registers
|
||
|
|
"ep_dbics" for the standard configuration registers as
|
||
|
|
they are locally accessed within the DIF CS space
|
||
|
|
"ep_dbics2" for the standard configuration registers as
|
||
|
|
they are locally accessed within the DIF CS2 space
|
||
|
|
"addr_space" used to map remote RC address space
|
||
|
|
- interrupts : one interrupt entries must be specified for main interrupt.
|
||
|
|
- num-ib-windows : number of inbound address translation windows
|
||
|
|
- num-ob-windows : number of outbound address translation windows
|
||
|
|
- ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument
|
||
|
|
should contain the register offset within syscon
|
||
|
|
and the 2nd argument should contain the bit field
|
||
|
|
for setting the bit to enable unaligned
|
||
|
|
access.
|
||
|
|
|
||
|
|
Optional Property:
|
||
|
|
- gpios : Should be added if a GPIO line is required to drive PERST# line
|
||
|
|
|
||
|
|
NOTE: Two DT nodes may be added for each PCI controller; one for host
|
||
|
|
mode and another for device mode. So in order for PCI to
|
||
|
|
work in host mode, EP mode DT node should be disabled and in order to PCI to
|
||
|
|
work in EP mode, host mode DT node should be disabled. Host mode and EP
|
||
|
|
mode are mutually exclusive.
|
||
|
|
|
||
|
|
Example:
|
||
|
|
axi {
|
||
|
|
compatible = "simple-bus";
|
||
|
|
#size-cells = <1>;
|
||
|
|
#address-cells = <1>;
|
||
|
|
ranges = <0x51000000 0x51000000 0x3000
|
||
|
|
0x0 0x20000000 0x10000000>;
|
||
|
|
pcie@51000000 {
|
||
|
|
compatible = "ti,dra7-pcie";
|
||
|
|
reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>;
|
||
|
|
reg-names = "rc_dbics", "ti_conf", "config";
|
||
|
|
interrupts = <0 232 0x4>, <0 233 0x4>;
|
||
|
|
#address-cells = <3>;
|
||
|
|
#size-cells = <2>;
|
||
|
|
device_type = "pci";
|
||
|
|
ranges = <0x81000000 0 0 0x03000 0 0x00010000
|
||
|
|
0x82000000 0 0x20013000 0x13000 0 0xffed000>;
|
||
|
|
#interrupt-cells = <1>;
|
||
|
|
num-lanes = <1>;
|
||
|
|
ti,hwmods = "pcie1";
|
||
|
|
phys = <&pcie1_phy>;
|
||
|
|
phy-names = "pcie-phy0";
|
||
|
|
interrupt-map-mask = <0 0 0 7>;
|
||
|
|
interrupt-map = <0 0 0 1 &pcie_intc 1>,
|
||
|
|
<0 0 0 2 &pcie_intc 2>,
|
||
|
|
<0 0 0 3 &pcie_intc 3>,
|
||
|
|
<0 0 0 4 &pcie_intc 4>;
|
||
|
|
pcie_intc: interrupt-controller {
|
||
|
|
interrupt-controller;
|
||
|
|
#address-cells = <0>;
|
||
|
|
#interrupt-cells = <1>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|