85 lines
3.6 KiB
Plaintext
85 lines
3.6 KiB
Plaintext
|
PCI bus bridges have standardized Device Tree bindings:
|
||
|
|
|
||
|
|
PCI Bus Binding to: IEEE Std 1275-1994
|
||
|
|
http://www.devicetree.org/open-firmware/bindings/pci/pci2_1.pdf
|
||
|
|
|
||
|
|
And for the interrupt mapping part:
|
||
|
|
|
||
|
|
Open Firmware Recommended Practice: Interrupt Mapping
|
||
|
|
http://www.devicetree.org/open-firmware/practice/imap/imap0_9d.pdf
|
||
|
|
|
||
|
|
Additionally to the properties specified in the above standards a host bridge
|
||
|
|
driver implementation may support the following properties:
|
||
|
|
|
||
|
|
- linux,pci-domain:
|
||
|
|
If present this property assigns a fixed PCI domain number to a host bridge,
|
||
|
|
otherwise an unstable (across boots) unique number will be assigned.
|
||
|
|
It is required to either not set this property at all or set it for all
|
||
|
|
host bridges in the system, otherwise potentially conflicting domain numbers
|
||
|
|
may be assigned to root buses behind different host bridges. The domain
|
||
|
|
number for each host bridge in the system must be unique.
|
||
|
|
- max-link-speed:
|
||
|
|
If present this property specifies PCI gen for link capability. Host
|
||
|
|
drivers could add this as a strategy to avoid unnecessary operation for
|
||
|
|
unsupported link speed, for instance, trying to do training for
|
||
|
|
unsupported link speed, etc. Must be '4' for gen4, '3' for gen3, '2'
|
||
|
|
for gen2, and '1' for gen1. Any other values are invalid.
|
||
|
|
- reset-gpios:
|
||
|
|
If present this property specifies PERST# GPIO. Host drivers can parse the
|
||
|
|
GPIO and apply fundamental reset to endpoints.
|
||
|
|
- supports-clkreq:
|
||
|
|
If present this property specifies that CLKREQ signal routing exists from
|
||
|
|
root port to downstream device and host bridge drivers can do programming
|
||
|
|
which depends on CLKREQ signal existence. For example, programming root port
|
||
|
|
not to advertise ASPM L1 Sub-States support if there is no CLKREQ signal.
|
||
|
|
|
||
|
|
PCI-PCI Bridge properties
|
||
|
|
-------------------------
|
||
|
|
|
||
|
|
PCIe root ports and switch ports may be described explicitly in the device
|
||
|
|
tree, as children of the host bridge node. Even though those devices are
|
||
|
|
discoverable by probing, it might be necessary to describe properties that
|
||
|
|
aren't provided by standard PCIe capabilities.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
|
||
|
|
- reg:
|
||
|
|
Identifies the PCI-PCI bridge. As defined in the IEEE Std 1275-1994
|
||
|
|
document, it is a five-cell address encoded as (phys.hi phys.mid
|
||
|
|
phys.lo size.hi size.lo). phys.hi should contain the device's BDF as
|
||
|
|
0b00000000 bbbbbbbb dddddfff 00000000. The other cells should be zero.
|
||
|
|
|
||
|
|
The bus number is defined by firmware, through the standard bridge
|
||
|
|
configuration mechanism. If this port is a switch port, then firmware
|
||
|
|
allocates the bus number and writes it into the Secondary Bus Number
|
||
|
|
register of the bridge directly above this port. Otherwise, the bus
|
||
|
|
number of a root port is the first number in the bus-range property,
|
||
|
|
defaulting to zero.
|
||
|
|
|
||
|
|
If firmware leaves the ARI Forwarding Enable bit set in the bridge
|
||
|
|
above this port, then phys.hi contains the 8-bit function number as
|
||
|
|
0b00000000 bbbbbbbb ffffffff 00000000. Note that the PCIe specification
|
||
|
|
recommends that firmware only leaves ARI enabled when it knows that the
|
||
|
|
OS is ARI-aware.
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
|
||
|
|
- external-facing:
|
||
|
|
When present, the port is external-facing. All bridges and endpoints
|
||
|
|
downstream of this port are external to the machine. The OS can, for
|
||
|
|
example, use this information to identify devices that cannot be
|
||
|
|
trusted with relaxed DMA protection, as users could easily attach
|
||
|
|
malicious devices to this port.
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
pcie@10000000 {
|
||
|
|
compatible = "pci-host-ecam-generic";
|
||
|
|
...
|
||
|
|
pcie@0008 {
|
||
|
|
/* Root port 00:01.0 is external-facing */
|
||
|
|
reg = <0x00000800 0 0 0 0>;
|
||
|
|
external-facing;
|
||
|
|
};
|
||
|
|
};
|