77 lines
3.0 KiB
Plaintext
77 lines
3.0 KiB
Plaintext
|
Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC)
|
||
|
|
|
||
|
|
The device node has following properties.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: should be "rockchip,<name>-gamc"
|
||
|
|
"rockchip,px30-gmac": found on PX30 SoCs
|
||
|
|
"rockchip,rk3128-gmac": found on RK312x SoCs
|
||
|
|
"rockchip,rk3228-gmac": found on RK322x SoCs
|
||
|
|
"rockchip,rk3288-gmac": found on RK3288 SoCs
|
||
|
|
"rockchip,rk3328-gmac": found on RK3328 SoCs
|
||
|
|
"rockchip,rk3366-gmac": found on RK3366 SoCs
|
||
|
|
"rockchip,rk3368-gmac": found on RK3368 SoCs
|
||
|
|
"rockchip,rk3399-gmac": found on RK3399 SoCs
|
||
|
|
"rockchip,rv1108-gmac": found on RV1108 SoCs
|
||
|
|
- reg: addresses and length of the register sets for the device.
|
||
|
|
- interrupts: Should contain the GMAC interrupts.
|
||
|
|
- interrupt-names: Should contain the interrupt names "macirq".
|
||
|
|
- rockchip,grf: phandle to the syscon grf used to control speed and mode.
|
||
|
|
- clocks: <&cru SCLK_MAC>: clock selector for main clock, from PLL or PHY.
|
||
|
|
<&cru SCLK_MAC_PLL>: PLL clock for SCLK_MAC
|
||
|
|
<&cru SCLK_MAC_RX>: clock gate for RX
|
||
|
|
<&cru SCLK_MAC_TX>: clock gate for TX
|
||
|
|
<&cru SCLK_MACREF>: clock gate for RMII referce clock
|
||
|
|
<&cru SCLK_MACREF_OUT> clock gate for RMII reference clock output
|
||
|
|
<&cru ACLK_GMAC>: AXI clock gate for GMAC
|
||
|
|
<&cru PCLK_GMAC>: APB clock gate for GMAC
|
||
|
|
- clock-names: One name for each entry in the clocks property.
|
||
|
|
- phy-mode: See ethernet.txt file in the same directory.
|
||
|
|
- pinctrl-names: Names corresponding to the numbered pinctrl states.
|
||
|
|
- pinctrl-0: pin-control mode. can be <&rgmii_pins> or <&rmii_pins>.
|
||
|
|
- clock_in_out: For RGMII, it must be "input", means main clock(125MHz)
|
||
|
|
is not sourced from SoC's PLL, but input from PHY; For RMII, "input" means
|
||
|
|
PHY provides the reference clock(50MHz), "output" means GMAC provides the
|
||
|
|
reference clock.
|
||
|
|
- snps,reset-gpio gpio number for phy reset.
|
||
|
|
- snps,reset-active-low boolean flag to indicate if phy reset is active low.
|
||
|
|
- assigned-clocks: main clock, should be <&cru SCLK_MAC>;
|
||
|
|
- assigned-clock-parents = parent of main clock.
|
||
|
|
can be <&ext_gmac> or <&cru SCLK_MAC_PLL>.
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- tx_delay: Delay value for TXD timing. Range value is 0~0x7F, 0x30 as default.
|
||
|
|
- rx_delay: Delay value for RXD timing. Range value is 0~0x7F, 0x10 as default.
|
||
|
|
- phy-supply: phandle to a regulator if the PHY needs one
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
gmac: ethernet@ff290000 {
|
||
|
|
compatible = "rockchip,rk3288-gmac";
|
||
|
|
reg = <0xff290000 0x10000>;
|
||
|
|
interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
|
||
|
|
interrupt-names = "macirq";
|
||
|
|
rockchip,grf = <&grf>;
|
||
|
|
clocks = <&cru SCLK_MAC>,
|
||
|
|
<&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>,
|
||
|
|
<&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>,
|
||
|
|
<&cru ACLK_GMAC>, <&cru PCLK_GMAC>;
|
||
|
|
clock-names = "stmmaceth",
|
||
|
|
"mac_clk_rx", "mac_clk_tx",
|
||
|
|
"clk_mac_ref", "clk_mac_refout",
|
||
|
|
"aclk_mac", "pclk_mac";
|
||
|
|
phy-mode = "rgmii";
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&rgmii_pins /*&rmii_pins*/>;
|
||
|
|
|
||
|
|
clock_in_out = "input";
|
||
|
|
snps,reset-gpio = <&gpio4 7 0>;
|
||
|
|
snps,reset-active-low;
|
||
|
|
|
||
|
|
assigned-clocks = <&cru SCLK_MAC>;
|
||
|
|
assigned-clock-parents = <&ext_gmac>;
|
||
|
|
tx_delay = <0x30>;
|
||
|
|
rx_delay = <0x10>;
|
||
|
|
|
||
|
|
};
|