When creating phy-handle property, an unsigned int value is created by
fdt_create_phandle, and memcpy is used to get the value, since DTS is
big endian, the value cannot be used directly on little endian SoCs,
it should be converted by cpu_to_fdt32.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.
Signed-off-by: York Sun <yorksun@freescale.com>
The workaround requires different setting for range 1 vs 2.
Also adjust timeout value for waiting for controller to be idle.
Signed-off-by: York Sun <yorksun@freescale.com>
Unfortunately U-Boot assumes that almost all numbers are in hex, including
partition numbers passed to e.g. "load". So, the command "part list mmc 0
-bootable devplist" should use hex when writing partition numbers into
$devplist, so they'll be correctly interpreted.
Change-Id: I9a70b19749643876baadb45efbc3decaef8bfee2
Fixes: 0798d6fd41 ("part: Add support for list filtering on bootable partitions")
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
With gcc 5.2 and later we get a bunch of "error: unknown type name" for
'uint8_t', 'uint32_t' and friends.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
This patch fixes the DDR3 initialization procedure in
order to comply with DDR3 standard. A 500 us delay is specified
between the DDR3 reset and clock enable signal. Until now,
this delay was not respected. Some DDR3 chips don't bother
but the bigger the RAM becomes the more likely it seems that
this delay is needed. We observed that DRAM > 256 MB from
the manufacturer Samsung have an issue when the specification
is not respected.
Changes:
1) Add a 1 ms wait for L3 timeout error trigger
2) Don't delay DDR3 initialization
Bit 31 of emif_sdram_ref_ctrl shouldn't be set because his
suppresses the initialization of DDR3
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Reviewed-by: James Doublesin <doublesin@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
VxWorks 7 kernels retrieve 'local-mac-addr' from dtb and use
that for NIC MAC address. As a result, when booting the same
kernel image on multiple boards, there will be address
conflicts.
So fixup MAC address when booting VxWorks 7 kernels
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add xlnx,xps-spi-2.00.a/b which is compatible string
listed in the Linux kernel.
Remove origin one which has no real background.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Used quite different name's and e-mail address, all of
them mapped to standard name and e-mail address.
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since all spi-flash core operations are moved into
sf_ops.c then it's better to renamed as spi-flash.c
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Used static for file-scope functions in sf_probe.c
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since spi_slave is a spi pointer in spi_flash{} then assign
spi_slave{} pointer to flash->spi and remove spi_slave
pointer argument to
- spi_flash_probe_slave
- spi_flash_scan
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
For assigning read_bar commands in spansion case, break
is missing this patch add that break.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
SST parts added on sf_params.c supports both SST_WR which consits
of both BP and WP and there is a spi controller ich which supports
only BP so the relevent _write hook set based on "slave->op_mode_tx"
hence there is no respective change required from flash side hance
removed these.
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Removed unneeded header includes in sf_ops and sf_probe
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Using macro's for flash power up read-only access code
leads wrong behaviour hence use idcode0 for runtime
detection, hence the flash which require this functionality
gets detected at runtime.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Most of the register access function are static,
so used simple name to represent each.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This patch removes unneeded ifdef and fixed accordingly.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Use static for file-scope functions and removed
them from header files.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
- Move bar read code below the bar write hance both
at once place, hence it easy for #ifdef macro only
once and readable.
- Move read_cmd_array at top
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
read_id code is related to spi_flash stuff
hence moved to sf_ops.
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Intension is that sf_ops should deals all spi_flash
related stuff and sf_probe (which should renamed future)
should be an interface layer for spi_flash versus spi drivers.
sf_ops => spi_flash interface
sf_probe => interface layer vs spi_flash(sf_probe) to spi drivers
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Rename spi_flash_validate_params to spi_flash_scan
as this code not only deals with params setup but
also configure all spi_flash attributes.
And also moved all flash related code into
spi_flash_scan for future functionality addition.
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Extend compatible list table for cdns,spi-r1p6 compatible string.
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Support qspi flashes for mx7dsabresd
1. introduce pin mux settings
2. enable qspi clock
3. introduce related macro definitions
Default QSPI is not enabled, since we need hardware rework to use QSPI,
see SPF-28590, page 9:
"
QSPI signals are muxed with EPDC_D[7:0]
When using QSPI: de-populate R388-R391, R396-R399
populate R392-R395, R299, R300
"
After hardware rework, define CONFIG_FSL_QSPI in mx7dsabresd.h. qspi
flashes can be deteced and read/erase/write. Log info:
"
=> sf probe
SF: Detected MX25L51235F with page size 256 Bytes, erase size 64 KiB, total 64 MiB
=> sf read 0x80000000 0 0x4000000
device 0 whole chip
SF: 67108864 bytes @ 0x0 Read: OK
=> sf erase 0 0x4000000
SF: 67108864 bytes @ 0x0 Erased: OK
=> sf write 0x80000000 0 0x4000000
device 0 whole chip
SF: 67108864 bytes @ 0x0 Written: OK
"
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
SPI_3WIRE is spi mode not spi flags, so this patch fixed
the spi-3wire checking throgh mode instead of flags.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
spi-3wire is used when SI/SO signals shared so get
the same from dts node and assign to mode on slave
plat->mode.
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Fix incorrect comment alignments.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a remark about SPL to this Kconfig option. Otherwise its identitcal
to the non-SPL version, which is confusing.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Add links for toolchains not available on kernel.org.
The sh4 toolchains from kernel.org dose not work for some boards,
so use the sh from Sourcery.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The read delays were set incorrectly, leading to reliability
issues at higher DRAM clock speeds. This commit adjusts this
to match the vendor boot0 behaviour.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add some spaces around operators.
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 6c739c5d added code to enable i2c bus 4 and 5 on the sun7i SoC
but forgot to extend the range check in clock_twi_onoff, resulting in
the clock not getting enabled.
The range-check is not needed at all, since clock_twi_onoff only gets
called with such high indexes when CONFIG_I2C3_ENABLE / CONFIG_I2C4_ENABLE
is set and Kconfig already only allows these on sun6i / sun7i.
This commit removes the range-check all together fixing i2c bus 4 and 5
not working on sun7i.
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
[hdegoede@redhat.com] Remove range check instead of extending it
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add dts and defconfig for h8homletv2 board.
H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
It has UART, ethernet, USB, HDMI, etc ports on it.
A83T patches are tested on this board.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Shaohui Xie
York Sun
Stephen Warren
Peter Robinson
angelo@sysam.it
Nishanth Menon
Egli, Samuel
Miao Yan
Kamil Lulko
Tom Rini
Michal Simek
Jagan Teki
Peng Fan
Stefan Roese
Thomas Chou
Jens Kuske
Olliver Schinagl
Hans de Goede
vishnupatekar