mcc200 and prs200 are old and have no maintainer. Remove the boards.
This also removes the mcc200 specific 1bpp BMP support from
common/lcd.c
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
The latest Xilinx tools generate ps7_init files that are explicitly
available under GPL. Change the makefile to allow drop in of those files
for building the SPL.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-and-tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
cppcheck reports:
[board/esd/common/auto_update.c:458]: (error) Uninitialized variable: cnt
The variable is not really used anywhere, so remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
The i2c_init function is no longer necessary.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Alt board was connected Power IC to channel 1 of sh-i2c. Source code that
controls this is already included, but channel 1 of sh-i2c is not enabled.
This enables channel 1 of sh-i2c, and can use.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Alt board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lager board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Koelsch board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Gose board has one ether port, this works using sh-ether driver.
This adds GPIO settings and driver settings in order to use the sh-ether.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix error detected by cppcheck:
[board/renesas/ecovec/ecovec.c:66]: (error) Buffer is accessed out of
bounds.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix error detected by cppcheck:
[board/matrix_vision/mvblx/sys_eeprom.c:353]: (error) Buffer is
accessed out of bounds.
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Michael Jones <michael.jones@matrix-vision.de>
Fix error detected by cppcheck:
[board/cogent/lcd.c:237]: (error) Invalid number of character (()
when these macros are defined:
'CONFIG_SHOW_ACTIVITY;CONFIG_STATUS_LED'.
Signed-off-by: Wolfgang Denk <wd@denx.de>
There are a number of places where U-Boot intentionally and legally
accesses physical address 0x0000, for example when installing
exception vectors on systems where these are located in low memory.
Add "cppcheck-suppress nullPointer" comments to silence cppcheck
where this is intentional and legal.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add example of an USB UDC configuration with DFU and UMS.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Add both host and mUSB support.
Currently, the selection between host USB and mUSB is done through the
config file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
CompuLab cm-t3517 is Computer on Module (CoM) based on AM3517 SoC.
Features: up to 256MB DDR2, up to 512MB NAND, USB hub, mUSB, WiFi, BT,
Analog audio codec, touch screen controller, LED.
Add basic support including:
LED, Serial console, NAND, MMC, GPIO, I2C, 256MB DRAM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Switch the default CD GPIO polarity to active low.
The current hsmmc driver assumption that the CD GPIO is active high, but
in the real hardware, usually the opposite holds.
The usual SD card socket has a mechanical switch which is grounded as
soon as a card is inserted.
Of course there might be some board logic which inverts the signal, but
as far as current users are concerned, there is no such logic.
Current U-Boot users either not using the CD functionality, or have a
different way (e.g. external to SoC GPIO controller) for checking the
card presence.
This patch also brings the polarity assumption in line with the Linux
kernel and adds appropriate comments.
This patch also might spare issues once the TWL GPIO driver will be
converted to the DM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
The fallback is used for cases when CONFIG_SERIAL_TAG defined, but the
eeprom is not used.
The fallback is useful for more than one CompuLab board, so move it to a
common location.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Extract the SMC911x initialization code to a common location where it
can be reused by other compulab omap3 based boards.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
The splash screen loading code can be reused by other compulab boards.
For now extract it to a common location for further reuse.
This also switches the splash code dependency from CONFIG_LCD to
CONFIG_SPLASH_SCREEN as it should normally be.
In addition this patch fixes the accidental dependency of the
get_board_mem_timings() function on CONFIG_LCD, by just moving the
splash code and leaving the above function intact.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Extract the USB hub reset code to a common location where it can be
reused by other compulab boards.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Move board revision handling code to a common location
for further reuse.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
disable internal delay through gmii_sel register, as this
is done in the ar8031 phy.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Currently Keystone2 Lamar evm (K2L) board is added, so update
Keystone2 readme file to have such one.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The 1GB DRAM configuration on mx6 solo uses 2 chip selects, but
the code tests 1GB DRAM configuration as if it is all present on one
chip select, and thus cannot see the full range of available memory.
Refactor the check to detect 1GB DRAM correctly.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Change the order in which GPIOs are toggled in SATA init sequence to
accomodate both SanDisk and Phison SSDs.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The scsi_init() function uses a GPIO so should request it. There is no
way to return an error here, and the request may be made multiple times,
so just ignore errors for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For now we won't want to mess with the existing configurations. Create a
new one which will enable device tree and driver model. Note that this
brings the device tree binary into u-boot-sunxi-with-spl.bin.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This was done automatically with the following bits of scripting.
The Kconfig choice content was generated with this script snippet:
for i in $(git grep -l CONFIG_ARCH_SUNXI configs/*) ; do
TARGET=$(sed -n -e 's/CONFIG_SYS_EXTRA_OPTIONS="\([^,"]\+\).*/\1/p' $i);
MACH=$(sed -n -e 's/.*CONFIG_\(MACH_SUN.I\)=./\1/p' $i)
echo "config TARGET_$TARGET"
echo " bool \"$TARGET\""
echo " depends on $MACH"
echo
done
defconfigs were updated with a sed script (t):
# Extract board from first entry of CONFIG_SYS_EXTRA_OPTIONS,
/^CONFIG_SYS_EXTRA_OPTIONS/ {
s/^\(CONFIG_SYS_EXTRA_OPTIONS="\)\([^,"]\+\),\?\(.*\)/\1\3\nCONFIG_TARGET_\2=y/;
# Print and delete first line (CONFIG_SYS_EXTRA_OPTIONS), leaving
# CONFIG_TARGET_<BOARD> in pattern space
P;D;
};
# Move CONFIG_TARGET_<BOARD> to hold space
/^CONFIG_TARGET/{h;n}
# Print CONFIG_TARGET_<BOARD> after CONFIG_MACH_<SOC> in either SPL or
# normal mode.
/^CONFIG_MACH/{p;g;p;n};
/^\+S:CONFIG_MACH/{p;g;s/^CONFIG_TARGET/+S:&/;p;n};
# Print any remaining lines normally
p;
Run as:
sed -i -n -f t $(git grep -l CONFIG_ARCH_SUNXI configs/*)
and then manually removing the one instance of CONFIG_SYS_EXTRA_OPTIONS="" from
Colombus_defconfig
board/sunxi/Makefile was updated with:
sed -e 's/^\(obj-\$(CONFIG_\)\(.*\)\().*+= dram_.*\)/\1TARGET_\2\3/g' board/sunxi/Makefile
and manually retabbing a few lines to line up again.
The board descriptions could certainly be improved.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
It's unfortunate that this needs to be present in both .config and spl/.config
since it makes it slightly hard to enable FEL mode for a regular defconfig. It
can be done with:
echo CONFIG_SPL_FEL=y >> .config
echo CONFIG_SPL_FEL=y >> spl/.config
Ideally only one of those would be needed.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now we have CONFIG_ARCH_SUNXI as the toplevel, CONFIG_MACH_SUN[45678]I as the
per-SoC option and leave CONFIG_TARGET_BLAH free for individual boards in the
future.
Done automatically with:
sed -i -e 's/TARGET_\(SUN[45678]I\)/MACH_\1/g' $(git grep -l TARGET_SUN[45678]I)
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
And make TARGET_SUN[45678]I a choice variable under this.
configs updated with:
sed -i -e 's/^\(\+S:\)\?CONFIG_TARGET_SUN.I=y/\1CONFIG_ARCH_SUNXI=y\n&/g' configs/*
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The defconfig for Ippo-q8h-v5 was incorrectly committed as
"Ippo_q8h". This patch renames it correctly, as well as
correct a typo in my name in the maintainers listing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Defining CONFIG_SYS_TEXT_BASE in config.mk is very old style.
Create CONFIG_SYS_TEXT_BASE option in Kconfig, but let it
depend on CONFIG_SPARC because we do not want to disturb
the other architectures that still define CONFIG_SYS_TEXT_BASE
in their header files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
For now, all the SPARC boards in U-Boot are provided by Gaisler.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Alt board use SCIF2, not SCIF0.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since board info structure is not still set up, the setting of RAM
address causes illegal access.
Therefore the setting of RAM address is removed.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since board info structure is not still set up, the setting of RAM
address causes illegal access.
Therefore the setting of RAM address is removed.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since board info structure is not still set up, the setting of RAM
address causes illegal access.
Therefore the setting of RAM address is removed.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0x70000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0x70000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0xB0000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The change of the CPU frequency is waited for until PLL0ST of the PLLECR is
set to 1.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Commit f91c09acf5 ("ARM: mx6: Add support for Kosagi Novena") missed to
add a MAINTAINERS file, so add Marek as the maintainer.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
155fa9af95 "spi: mxc: fix sf probe when using mxc_spi" break
spi flash detection on the aristainetos board. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environment is set
to that device.
Signed-off-by: Ye.Li <B37916@freescale.com>
The vct board can be built with various variants which are
configured via CONFIG_SYS_EXTRA_OPTIONS. This is deprecated. Thus
add new Kconfig options for those board variants.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
The dbau1x00 board can be built with various variants which are
configured via CONFIG_SYS_EXTRA_OPTIONS. This is deprecated. Thus
add new Kconfig options for those board variants.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Now the user can separately select the CPU type. Thus the
targets qemu_mips and qemu_mips64 can be merged to a single
target.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Now the user can select the CPU type for each target. Thus
CONFIG_SYS_CPU could be set globally.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Commit f91c09acf5 ("ARM: mx6: Add support for Kosagi Novena") missed to
add a MAINTAINERS file, so add Marek as the maintainer.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
[1] arch/arm/include/asm/arch-at91/at91_shdwn.h
The top9000 was the last board to use this header file.
It was removed by commit d58a9451e7 (ppc/arm: zap EMK boards).
[2] board/matrix_vision/common/*
Some Matrix Vision boards were dropped by commit e7a565638a
(powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7)
and commit af55e35d33
(powerpc: mpc5xxx: remove board support for MVBC_P and MVSMR).
Since then these files have been unused.
[3] include/usb/omap1510_udc.h
The omap5912osk was the last board to use this header file.
It was removed by commit 62d636aa2a
(omap: remove omap5912osk board support).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-By: Wolfgang Denk <wd@denx.de>
Setting gpio value before dm gpio init has no effect,
so now, odroid gpio settings are moved after the gpio uclass init.
Using non-requested gpio pin cases printing error messages.
To avoid this, gpio_request() is added for those gpios.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch fixes conflict between PHY pins becoming outputs after reset and
imx6 still driving the pins. It also fixes the reset timing as recommended by
the PHY datasheet.
Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
The older 'mr' variant and the generic variant of the
OT1200 differ in some places. As the name suggests the
generic variant supports more boot devices.
In order to be compatible with the 'mr' variant we define
some 'feature' GPIOs. On the 'mr' variant this pads are
not connected so we define their state with the help
of the internal pullups.
On the generic variant this GPIOs are connected and
represent the state of the hardware.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Commit 155fa9af95 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Add support for the 4.3'' Seiko WVGA parallel display.
In order to direct the splash screen to the Seiko display:
=> setenv panel SEIKO-WVGA
=> save
=> reset
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add support for the Kosagi Novena board. Currently supported are:
- I2C busses
- FEC Ethernet
- MMC0, MMC1, Booting from MMC
- SATA
- USB ports
- USB Ethernet
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Nikolay Dimitrov <picmaster@mail.bg>
Reviewed-by: Nikolay Dimitrov <picmaster@mail.bg>
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
The following bard configurations have been without active maintenance
for a long time, and the board maintainer agrees to have them removed:
MPC5200: TOP5200, MINI5200, EVAL5200
MPC860: TOP860
at91sam9xeXXX: top9000eval_xe, top9000su_xe
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
[trini: Add missing Kconfig removals]
Signed-off-by: Tom Rini <trini@ti.com>
This file should contain the bin_hdr generated by the original Marvell
U-Boot implementation. As this is currently not included in this
U-Boot version, we have added this placeholder, so that the U-Boot
image can be generated without errors.
If you have a known to be working bin_hdr for your board, then you
just need to replace this text file here with the binary header
and recompile U-Boot.
In a few weeks, mainline U-Boot will get support to generate the
bin_hdr with the DDR training code itself. By implementing this code
as SPL U-Boot. Then this file will not be needed any more and will
get removed.
Signed-off-by: Stefan Roese <sr@denx.de>
LaCie Wireless Space has no defined maintainer.
Set myself as maintainer, since I own one of these.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This is the only used of CONFIG_SPI_X macro, just zap this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Remove this board as this is the only one last user of eeprom_probe(),
which is pretty non-standard stuff.
This patch also removes all the PHP, SQL and CSS stuff from U-Boot,
which probably makes U-Boot a bit less IoT ;-)
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board uses eeprom accessors in an incorrect way. The board
is old and unsupported, just zap it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is the only user of CONFIG_SYS_EEPROM_X40430 , remove
it so the EEPROM command code can be cleansed of the related code
as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
The file board/Marvell/include/mv_gen_reg.h is incompatible with
the GPL (see for example the "MARVELL RESERVES THE RIGHT AT ITS SOLE
DISCRETION TO REQUEST THAT THIS CODE BE IMMEDIATELY RETURNED TO
MARVELL" clause). As this cannot be fixed, we remove the file and all
code that depends on it. Fortunately this only affects some very old
boards that have long reached EOL:
CPCI750
DB64360
DB64460
p3m750
p3m7448
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
The config targets described in README are not present
any more, update the info to currently used targets.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add a Kconfig option which users can select when they want to boot older
kernels, e.g. the linux-sunxi 3.4 kernels. For now this just forces the pll5
"p" value to 1 (divide by 2) as that is what those kernels are hardcoded too,
in the future this may enable further workarounds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@ti.com>
--
Changes in v2:
-s/CONFIG_OLD_KERNEL_COMPAT/CONFIG_OLD_SUNXI_KERNEL_COMPAT.
-Move the code block setting P(1) for old kernels to where P gets cleared
Ippo q8h is a series of A23 tablet boards. This defconfig
is for v5 of these boards, though for u-boot purposes they
are mostly the same.
See: http://linux-sunxi.org/Ippo_q8h
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The basic blocks of the A23 are similar to the A31 (sun6i). Re-use
sun6i code for initial clock, gpio, and uart setup.
There is no SPL support for A23, as we do not have any documentation
or sample code for DRAM initialization.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Unify the sunxi Kconfig code, instead of having separate code blocks for
each of sun4i - sun7i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
None of the known sunxi devices actually use mmc1 routed through PH, where
as some devices do actually use mmc1 routed through PG, so change the routing
of mmc1 to PG. If in the future we encounter devices with mmc1 routed through
PH, we will need to change things to be a bit more flexible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sunxi SOCs can boot from both mmc0 and mmc2, detect from which one we're
booting, and make that one "mmc dev 0" so that a single u-boot binary can
be used for both the onboard eMMC and for external sdcards.
When we're booting from mmc2, we make it dev 0 because that is where the SPL
will load the tertiary payload (the actual u-boot binary in our case) from,
see: common/spl/spl_mmc.c, which has dev 0 hardcoded everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Note we also drop the SPL check for initializing the 2nd mmc slot, the SPL
check is not necessary with Kconfig, because only options explicitly marked
as also being for the SPL get set during SPL builds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Colombus board is an A31 evaluation board from WITS Technology.
Maxime has kindly agreed to maintain this board.
[1] http://lists.denx.de/pipermail/u-boot/2014-September/190043.html
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a new sun6i machine that supports UART and MMC.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: use SPDX labels, adapt to Kconfig system, drop ifdef
around mmc and smp code, drop MACH_TYPE]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Mele M3 is yet another Allwinnner based Android top set box from Mele.
It uses a housing similar to the A2000, but without the USM sata storage slot
at the top.
It features an A20 SoC, 1G RAM, 4G eMMC (unique for Allwinner devices),
100Mbit ethernet, HDMI out, 3 USB A receptacles, VGA, and A/V OUT connections.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This adds support for the Olimex A20-OLinuXino-Lime2
https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXIno-LIME2
Differences to previous Lime boards are 1GB RAM and gigabit ethernet
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The platform_data definitions are generally referenced from both
drivers and board files. That is why header files defining
platform_data sturectures are placed in "include" directory,
but our top level "include" directory is already too cluttered.
Let's collect platform_data definitions under the directory
"include/dm/platform_data" like Linux gathers ones around under
"include/linux/platform_data".
This commit moves two header files:
include/serial_mxc.h -> include/dm/platform_data/serial_mxc.h
include/serial_pl01x.h -> include/dm/platform_data/serial_pl01x.h
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Adjust the configuration for the am33xx boards, including beagleboard,
to use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
The gpmc_init() function already calls enable_gpmc_cs_config() for chip
select 0. Although the bus width is configured for 16 bit, it gets
reconfigured correctly in the omap_gpmc driver later.
Remove the enable_gpmc_cs_config() function call and the associated
gpmc_nand_config[] array.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
In the case of Beaglebone Black we only want to set the NAND or NOR cape
pinmux when the config has been specifically modified by the user for
this non-default case. Make the default be to set the MMC1 (eMMC)
pinmux. We don't need similar changes for Beaglebone White as there is
nothing on MMC1 by default there.
Signed-off-by: Tom Rini <trini@ti.com>
Separate overo module and expansion board MUX configuration. This allows
an foreign expansion board to use the boot loader without any adaption.
It only needs to save the expansion name in the EEPROM to load a
specific device tree.
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Move ethernet setup to the board_eth_init function and select
the available network devices via expansion id.
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
This patch adds the DDR3 ECC support to enable ECC in the DDR3
EMIF controller for Keystone II devices.
By default, ECC will only be enabled if RMW is supported in the
DDR EMIF controller. The entire DDR memory will be scrubbed to
zero using an EDMA channel after ECC is enabled and before
u-boot is re-located to DDR memory.
An ecc_test environment variable is added for ECC testing.
If ecc_test is set to 0, a detection of 2-bit error will reset
the device, if ecc_test is set to 1, 2-bit error detection
will not reset the device, user can still boot the kernel to
check the ECC error handling in kernel.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
For K2E and K2L SoCs clock output from PASS PLL has to be enabled
after NETCP domain and PA module are enabled. So create new function
for that and call it after PA module is enabled.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Remove unused tx_send_loop variable.
Removes duplicated get_link_status() call from the
keystone2_eth_send_packet().
The emac_gigabit_enable() is called at opening Ethernet and there is no
need to enable it on sending each packet. So remove that call
from keystone2_eth_send_packet() as well.
The calling of power/clock up functions are mostly the responsibility
of SoC/board code, so move these functions to appropriate place.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The header file for the driver should be in correct place.
So move it to "arch/arm/include/asm/ti-common/keystone_net.h"
and correct driver's external dependencies. At the same time
align and correct some definitions.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The initialization of PLLs is a part of board specific code, so
move it appropriate places.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The maxBCM board is equipped with the Marvell Armada-XP MV78460 SoC. It
integrates an SPI NOR flash and an Marvell 88E6185 switch.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic support for the Marvell DB-MV784MP-GP evaulation
board. This is the first board that uses the recently created
Armada XP 78460 SoC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Additionally the SDRAM address decoding register address is not hard coded
in the C code any more. A define is introduced for this base address.
This makes is possible to use those gpio functions from other MVEBU SoC's
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This makes is possible to use those gpio functions from other MVEBU SoC's as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Commit 155fa9af95 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
The built-in SMSC 95xx chip doesn't know its own MAC address. Instead,
we must query it from the VC firmware; it's probably encoded in fuses
on the BCM2835.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Convert the BCM2835 GPIO driver to use driver model, and switch over
Raspberry Pi to use this, since it is the only board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Now that serial and GPIO are available for iMX.6, move cm_fx6 over as an
example.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Use gpio_request for all the gpios that are utilized by various
subsystems in cm-fx6, and refactor the relevant init functions
so that all gpios are requested during board_init(), not during
subsystem init, thus avoiding the need to manage gpio ownership
each time a subsystem is initialized.
The new division of labor is:
During board_init() muxes are setup and gpios are requested.
During subsystem init gpios are toggled.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This converts the Tegra SPI drivers to use driver model. This is tested
on:
- Tegra20 - trimslice
- Tegra30 - beaver
- Tegra124 - dalmore
(not tested on Tegra124)
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Since spi_flash.h is supposed to be the public API for SPI flash, move
private things to sf_internal.h. Also tidy up a few comment nits.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust this board to use the driver model soft_spi implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Move the exynos SPI driver over to driver model. This removes quite a bit
of boilerplate from the driver, although it adds some for driver model.
A few device tree additions are needed to make the SPI flash available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
With driver model GPIOs must be requested before use. Make sure this is
done correctly.
(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)
Signed-off-by: Simon Glass <sjg@chromium.org>
The wrong header is being included, thus requiring the code to re-declare
the generic GPIO interface in each GPIO header.
Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add proper initialization of GPIO pins used by software i2c.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update Apalis T30 as per the following commits
c369139234
tegra: dts: Add serial port details
461be2f96e
kconfig: remove redundant "string" type in arch and board Kconfigs
f1ef2b6233
kconfig: move CONFIG_DEFAULT_DEVICE_TREE to kconfig
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix ASIX USB to Ethernet reset which due to the new driver model Tegra
GPIO driver changes now requires a label string to be provided
otherwise the reservation and subsequent direction/value calls will
fail.
This fixes a regression introduced by commit:
2fccd2d96b
tegra: Convert tegra GPIO driver to use driver model
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds board support for the Toradex Apalis T30 a computer on
module which can be used on different carrier boards.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot and environment storage
- Gigabit Ethernet (once Thierry's PCIe as well as my E1000 resp. i210
fixes hit mainline)
- MMC/SD cards (both 8-bit as well as 4-bit slot)
- USB client/host (dual role port as client e.g. for DFU/UMS, other two
ports as host)
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This pinmux tables currently omit any configuration for PCIe clk_req,
wake, and rst pins, which in turn causes intermittent failures in
U-Boot's PCIe support. Import an updated version of the pinmux tables
which rectifies this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Provide a public declaration of the board_spi_cs_gpio()
callback for i.MX SPI chip selects to prevent the warning
"Should it be static?" when compiling with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update readme file for Keystone II EVM boards to actual sources.
Also correct some typos. For now the Edison evaluation board is
added, README for K2E is mostly the same, so update README to
contain information also for K2E evm. Rename file to README as
it contains information for all keystone evm boards.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The lines COL (collision detect) and CRS (carrier sense) needs to be connected
and muxed to the CPSW MAC for a proper function in half-duplex Mode of the
interface.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: Tom Rini <trini@ti.com>
fix broken SPI access by adding/activating BOARD_EARLY_INIT_F
functionality and calling spi_init_f() from there.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Fix typo of commit d4e53f063d.
i2c2 pullup resisters are controlled by bit 0 of CONTROL_PROG_IO1.
It's value after reset is 0x00100001.
In order to clear bit 0, original code write 0xfffffffe to
CONTROL_PROG_IO1 and toggle almost all default values.
Original code affect following:
* disable i2c1 pullup resisters
* increase far end load setting for many modules
* setup invalid SC/LB combination
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Steve Kipisz <s-kipisz2@ti.com>
This board has been orphaned for more than 6 months.
It is the last board defining CONFIG_APM821XX.
The code inside #ifdef CONFIG_APM821XX should be removed too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
On OMAP platforms, SATA controller provides the SCSI subsystem
so implement scsi_init().
Get rid of the unnecessary sata_init() call from dra7xx-evm
and omap5-uevm board files.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Add default eeprom bus setting.
This addresses the trimslice compile error that was introduced
with the addition of this setting.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
In order for the gmac nic to work reliable on the Bananapi, we need to set
bits 10-12 GTXDC "GMAC Transmit Clock Delay Chain" of the GMAC clk register
(0x01c20164) to 3.
Without this about 9 out of 10 ethernet packets get lost, with this setting
there is no packet loss.
So far setting these bits is only necessary on the Bananapi, so this commit
solves this with a bit of #ifdef CONFIG_BANANAPI code. If in the future we
need to do something similar for other boards, we can create a specific
CONFIG_FOO option for this then.
Reported-by: Karsten Merker <merker@debian.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Zoltan HERPAI <wigyori@openwrt.org>
Tested-by: Tony Zhang <tony.zhang@lemaker.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This change fixes suspend/resume issue in the kernel caused
by the wrong 'aclk_cores' clock value expected by the kernel.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The email address of Rajeshwari Shinde <rajeshwari.s@samsung.com>
is not working.
This commit gives Akshay the maintainership of Snow and
SMDK5420 boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Removed settings in unsupported register fields. They didn’t
do anything, and in most cases, were not documented in the
reference manual.
Changed register settings to comply with JEDEC required values.
Changed timing parameters because they included full clock
periods that were doing nothing.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
[rebased on v2014.10-rc2]
Signed-off-by: Stefan Agner <stefan@agner.ch>
The HPD pin and RX_SENSE registers have proven to be less reliable
than using I2C on the EDID pins for detection of an HDMI monitor.
In particular, when the HDMI output is reset through a "reboot"
cycle, the detect_hdmi() routine often bounces, resulting in
a failure to detect a connected monitor.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add support for WVGA (800x480) panels using VESA GTF timings over
LVDS.
No auto-detection is supported, so you must configure this panel
manually through the 'panel' environment variable:
U-Boot > setenv panel svga
U-Boot > saveenv && reset
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add support for an Ampire 1024x600 LVDS panel with integrated Ilitek
capacitive touch screen.
Auto-detection is enabled, so no explicit configuration is needed.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add support for 800x600 18-bit RGB displays using VESA GTF timings.
No auto-detection is supported, so you must configure this panel
manually through the 'panel' environment variable:
U-Boot > setenv panel svga
U-Boot > saveenv && reset
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add support for the Touch Revolution Fusion7 display: 800x480 RGB
with a custom F0710A resistive touch controller.
Auto-detection of this panel is supported so no configuration is
required.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
This patch adds support for LVDS WXGA displays that use the SPWG encoding
standard instead of JEIDA.
No auto-detection is enabled and you must explicitly set the 'panel'
environment variable:
U-Boot > setenv panel LDB-WXGA-S
U-Boot > saveenv && reset
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add support for LG 9.7" LVDS panel (1024x768) with integrated eGalax
touch screen.
Note that this panel differs only slightly from the Hannstar XGA panel
(margins).
No auto-detection is available because it shares the same touch controller
as the Hannstar-XGA display, so you'll need to configure it through the
'panel' environment variable:
U-Boot > setenv panel LG-9.7
U-Boot > saveenv && reset
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add support for a 1/4 VGA panel with a 24-bit RGB interface.
No auto-detection is enabled, so you must configure the 'panel'
environment variable to use this display:
U-Boot > setenv panel qvga
U-Boot > saveenv && reset
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add support for Boundary Devices 7" and 10.1" 1280x800 displays with
integrated FocalTech ft5x06 10-point touch controller.
Because they share the touch controller with the 1024x600 displays,
auto-detection is disabled and you must explicitly set the 'panel'
environment variable:
U-Boot > setenv panel LDB-WXGA
U-Boot > saveenv && reset
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Include declarations of board_ehci callbacks to prevent compiler warnings
and enforce function prototypes.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Testing shows that the Micrel PHY may not be completely out
of reset if accessed immediately.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Declare locally-used data structures and functions as
static and pull in header files to prevent compiler warnings
of "Should it be static?" when building with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Configure CLKO outputs for SGTL5000, CSI camera.
The sys_mclk output for the SGTL500 in particular prevents
Windows CE from properly driving audio.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Ensure that cameras and USB OTG power are in a stable (reset)
state at reset by configuring their pads and toggling GPIOs.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Pads SD2_CLK/CMD/DAT0-3 are connected to an SDIO WiFi device on
Nitrogen and unconnected on BD-SL-i.MX6 (sabre lite).
Configure them as SDIO pins to prevent them from being in a state
that confuses the WiFi part.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The same logic applies to both SD card slots, only with different
GPIOs and the code should make that easier to see.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Several customers have asked to leave the display quiet during
boot, so allow the user to express this request by the presence
of environment variable "novideo".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Move icache_enable() and dcache_enable() function calls from
board code into the CPU code and into the enable_caches()
function. This is how the cache enabling code was designed
to work.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
The code is now fixed to the point where we can safely enable
the L1 data cache. Enable the D-Cache and set it as write-alloc.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Cosmetic change to the checkboard() function output. Align the
output with the rest of initial output produced by U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
The bi_boot_params must point to offset 0x100 in DRAM. Make it so.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Add some stub defines, which are used by the clock code, but are
missing from the auto-generated header file for the SoCFPGA family.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
This patch adds support for the OT1200 series of devices.
Following components are used in u-boot:
+ ethernet
+ i2c
+ emmc
+ gpio
For more details see README.
Changes v1 > v2
- make use of enable_cspi_clock(..)
- fix usage of OUTPUT_40OHM define
- added README
Changes v2 > v3
- improve spelling in README
- added own copy of mx6q_4x_mt41j128.cfg
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Update DDR calibration settings based on a larger test set.
The initial values were gathered on a small number of boards,
and have been found to fail on some boards under load.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Zeroing GD in board_init_f() is not needed any more. As its now done in
crt0.S. The patch that clears the GD in crt0.S is this one:
aae2aef9 [arm: Set up global data before board_init_f()] from Simon.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2
arm2 board. Since the LPDDR2 arm2 board has different DDR size, use
CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE.
Signed-off-by: Ye.Li <B37916@freescale.com>
This patch adds the i.MX6DL arm2 board support. The i.MX6DL ARM2
shared the same board with i.MX6Q ARM2 board since the i.MX6DL is
pin-pin compatible with i.MX6Q.
The patch also support the DDR 32-BIT mode option. Please define
CONFIG_DDR_32BIT in the board configure file to enable DDR 32-BIT
mode.But due to the board design, it's 64bit DDR buswidth physically,
so, if you CONFIG_DDR_32BIT, the DDR memory size will be half of it.
Signed-off-by: Ye.Li <B37916@freescale.com>
Add fine-tuning for the DRAM configuration according to the DRAM chip
datasheet. THis configuration applies to both Hynix HY5DU12622DTP and
Samsung K5H511538J-D43 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Enable the power to the USB port only when the USB port is really needed.
Do not enable the power unconditionally.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Spin table is at the very beginning of boot code. Each core has an individual
release address within the spin table, the ft_cpu_setup fn updates the
"cpu-release-addr" property of each cpu node with the corresponding release
address.
Also fix CPU_RELEASE_ADDR to point to secondary_boot_func.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
DP-DDR is used for DPAA, separated from main memory pool for general
use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit).
Signed-off-by: York Sun <yorksun@freescale.com>
Since commit ddaf5c8f30
(patman: RunPipe() should not pipe stdout/stderr unless asked),
Patman spits lots of "Invalid MAINTAINERS address: '-'"
error messages for patches with global changes.
It takes too long for Patman to process them.
Anyway, "M: -" does not carry any important information.
Rather, it is just like a place holder in case of assigning
a new board maintainer. Let's comment out.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The "S: Orphan" in MAINTAINERS means that the maintainer in the
"M:" field is unreachable (i.e. the email address is not working).
(Refer to the definition of "Orphan" adopted in U-Boot
in the log of commit 31f1b654b2,
"boards.cfg: move boards with invalid emails to Orphan")
For patch files adding global changes, scripts/get_maintainer.pl
adds bunch of such invalid email addresses, which results in
tons of annoying bounce emails.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '
/^M:[[:blank:]]/ {
N
/S:[[:blank:]]Orphan/s/^/#/
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Each CPU of PowerPC has its default linker script under the CPU
directory, except mpc8xx.
Every mpc8xx board has its own linker script under the board
directory, resulting in lots of duplication of linker scripts.
I notice eight mpc8xx boards have the same linker script.
We can decrease the number of linker scripts by putting a single
default linker script, arch/powerpc/cpu/mpc8xx/u-boot.lds.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
T1042QDS (T1042 is T1040 Personality without L2 switch) supports following
sgmii interfaces with serdes protocol 0xA7
-SGMII-MAC3 on Lane B - slot 7
-SGMII-MAC5 on Lane H - slot 7
-SGMII2.5G-MAC1 on Lane C - slot 6
-SGMII2.5G-MAC2 on Lane D - slot 5
Add support of above sgmii interfaces
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
DDR-ODT require cfg_dram_type switch set properly as per DDR type.
T1040RDB, T1042RDB boards have DDR3L type DDR, so cfg_dram_type
should be set to OFF for DDR3L
Update t104xrdb/README for switch setting
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1042RDB is a Freescale reference board that hosts the T1042 SoC
(and variants). The board is similar to T1040RDB, T1042 is a reduced
personality of T1040 SoC without Integrated 8-port Gigabit(L2 Switch).
T1042RDB is configured with serdes protocol 0x86 which can support
following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 1 SGMII on DTSEC3
DTSEC1, DTSEC2 are not connected on board.
This Patch
- add T1042RDB support
- updates README file for T1042RDB details and update commands for switching
to alternate banks from vBank0 to vBank4 and vice versa
This patch also does minor clean ups for fdt defines for T1042RDB and
T1042RDB_PI board
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support of rcw for T1042RDB, it makes following changes :
- Adds t1042_rcw.cfg file for serdes protocol 0x86 for T1042RDB
- Renames t1042_pi_rcw.cfg file from t1042_rcw.cfg and also updates
comments for valid serdes protocol which is 0x06
- Also updates CONFIG_SYS_FSL_PBL_RCW for T1042RDB
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS2085a has 2 regions in system memory map. Region1 is default map from
where system boots. Once u-boot is moved to DDR, IFC is re-mapped to
Region2.
So, update gd->env_addr to reflect correct address.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MXC SPI driver has a feature whereas a GPIO line can be used to force CS high
across multiple transactions. This is set up by embedding the GPIO information
in the CS value:
cs = (cs | gpio << 8)
This merge of cs and gpio data into one value breaks the sf probe command:
if the use of gpio is required, invoking "sf probe <cs>" will not work, because
the CS argument doesn't have the GPIO information in it. Instead, the user must
use "sf probe <cs | gpio << 8>". For example, if bank 2 gpio 30 is used to force
cs high on cs 0, bus 0, then instead of typing "sf probe 0" the user now must
type "sf probe 15872".
This is inconsistent with the description of the sf probe command, and forces
the user to be aware of implementaiton details.
Fix this by introducing a new board function: board_spi_cs_gpio(), which will
accept a naked CS value, and provide the driver with the relevant GPIO, if one
is necessary.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Provide cgtqmx6eval board its own variant of ddr
setup config file. Move board/freescale/imx/ddr/
mx6q_4x_mt41j128.cfg to board/freescale/mx6sabresd/
as this is was designed for the mx6sabresd board.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
- Use _defconfig instead of _config, but still _config is working.
- Corrected README.sandbox path in ./README
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add NOR flash hardware init function, including SMC and PIO
configuration.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch implements a workaround to fix DDR3 memory issue.
The code for workaround detects PGSR0 errors and then preps for
and executes a software-controlled hard reset.In board_early_init,
where logic has been added to identify whether or not the previous
reset was a PORz. PLL initialization is skipped in the case of a
software-controlled hard reset.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Keegan Garcia <kgarcia@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
commit d6d07a9b... arm: vf610: add NAND support for vf610twr
generates the following warnings:
WARNING: no status info for 'vf610twr_nand'
WARNING: no maintainers for 'vf610twr_nand'WARNING: no status info for
'vf610twr_nand'
This is due to the fact that vf610twr_nand_defconfig has no Maintainer.
This patch proposed Alison as Maintainer and fix it.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Alison Wang <b18965@freescale.com>
CC: Stefan Agner <stefan@agner.ch>
We do not have to distinguish CONFIG_TARGET_VEXPRESS_AEMV8A_SEMI
from CONFIG_TARGET_VEXPRESS_AEMV8A. Rename the former to the latter.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Cc: David Feng <fenghua@phytium.com.cn>
i2c_pad_info1 is only used locally, so it can be made static.
Fix the following sparse warning:
board/freescale/mx6sxsabresd/mx6sxsabresd.c:160:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This adds NAND support for the Vybrid tower system (TWR-VF65GS10)
provided by the vf610_nfc driver. Full 16-Bit bus width is
supported. Also an aditional config vf610twr_nand is introduced
which gets the environment from NAND. However, booting U-Boot from
NAND is not yet possible due to missing boot configuration block
(BCB).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This is an implementation of GPIOs for Tegra that uses driver model. It has
been tested on trimslice and also using the new iotrace feature.
The implementation uses a top-level GPIO device (which has no actual GPIOS).
Under this all the banks are created as separate GPIO devices.
The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7,
..., Z0..Z7, AA0..AA7, etc.
Since driver model is not yet available before relocation, or in SPL, a
special function is provided for seaboard's SPL code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently mx6dlsabresd shares the same DCD settings with the nitrogen board.
Provide a DCD configuration file specific to mx6dlsabresd with the settings
recommended by the Freescale hardware team.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The leds array within struct ventana has space for 3 elements, but the
setup_board_gpio() function tries to set up 4 GPIOs for LEDs. Recent
versions of GCC complain about that:
board/gateworks/gw_ventana/gw_ventana.c: In function 'setup_board_gpio':
board/gateworks/gw_ventana/gw_ventana.c:987:27: warning: iteration 3u invokes undefined behavior [-Waggressive-loop-optimizations]
if (gpio_cfg[board].leds[i])
^
board/gateworks/gw_ventana/gw_ventana.c:986:2: note: containing loop
for (i = 0; i < 4; i++) {
^
Fix this by making the upper bound of the loop match the array size.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Most Gateworks Ventana boards use a PLX PEX860x PCIe switch for PCIe expansion.
These boards use GPIO on the PLX device as PERST# for the downstream ports
thus we assert this when the PLX is enumerated.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for SATA.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Use Compulab eeprom module to obtain revision number, serial number, and
mac address from the EEPROM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add support for all 3 I2C busses on Compulab CM-FX6 CoM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add USB and USB OTG host support for Compulab CM-FX6 CoM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add ethernet support for Compulab CM-FX6 CoM
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add initial support for Compulab CM-FX6 CoM.
Support includes MMC, SPI flash, and SPL with dynamic DRAM detection.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Create CONFIG_SYS_I2C_EEPROM_BUS #define to tell the EEPROM
module what I2C bus the EEPROM is located at. Make cl_eeprom_read()
switch to that bus when reading EEPROM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
There are many similarities between the IMX6QUAD/IMX6DUAL and there are
many similarities between the IMX6SOLO/IMX6DUALITE. Add a 'soctype' env
variable that tells you which type you have.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5520 has an IMX6Q SoC with 512MB of DDR3, 256MB of NAND flash as well as:
* 2x MiniPCIe sockets
* 2x USB host sockets
* 2x i210 GigE
* HDMI out
* digital I/O expansion
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX6 MMDC calibration registers depend on propagation delay and capacitive
loading between the SoC's MMDC and the DDR3 chips. On the Ventana boards the
board layout varies little in trace-lengths such that propagation delays are
irrelevant thus we can simply things by using calibration values obtained
from various board layouts based on a common SoC and DDR chip configuration.
This eliminates board-model from being needed allowing more flexibility. These
values were tested on a large sample size of Gateworks Ventana boards ranging
in layout, and memory configuration over the entire temperature range supported.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This patch adds the TWR_LCD_RGB card/HDMI options and the common
configuration for DCU on LS1021ATWR board.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
On LS1021ATWR, Silicon's Sii9022A HDMI Transmitter
is used. This patch adds the common setting for this
chip.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021ATWR board.
One DDR controller
DUART1 is used as the console
For the detail board information, please refer to README.
Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021AQDS board.
One DDR controller
DUART1 is used as the console
For the detail board information, please refer to README.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
fsl_enet.h defines the mapping of the usual MII management
registers, which are included in the MDIO register block
common to Freescale ethernet controllers. So it shouldn't
depend on the CPU architecture but it should be actually
part of the arch independent fsl_mdio.h.
To remove the arch dependency, merge the content of
asm/fsl_enet.h into fsl_mdio.h.
Some files (like fm_eth.h) were simply including fsl_enet.h
only for phy.h. These were updated to include phy.h instead.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Previously, we used to statically assign values for vl_col, vl_row and
vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16.
Introducing the function exynos_lcd_early_init() would take care of this
assignment on the fly by parsing FIMD DT properties, thereby allowing us
to remove LCD_XRES and LCD_YRES from the main config file.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for Olimex A20-OLinuXino-LIME board.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Patch is the result of:
sed -i -e 's/FTDFILE/FDTFILE/g' board/sunxi/Kconfig configs/* include/configs/sunxi-common.h
sed -i -e 's/ftdfile/fdtfile/g' board/sunxi/Kconfig
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[ ijc -- s/Spotted-by/Reported-by/ and resolve conflict vs "remove
redundant "SPL" from CONFIG_SYS_EXTRA_OPTIONS" ]
This patch changes MPLL from 800MHz to 880MHz on Odroid.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Inderpal's email address is not working any more.
Chander will be a new maintainer.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This config is valid for two devices:
- Odroid X2,
- Odroid U3.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This board file supports standard features of Odroid X2 and U3 boards:
- Exynos4412 core clock set to 1000MHz and MPLL peripherial clock set to 800MHz,
- MAX77686 power regulator,
- USB PHY,
- enable XCL205 - power for board peripherials
- check board type: U3 or X2.
- enable Odroid U3 FAN cooler
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change adds setup of environmental board info using
get_board_name() and get_board_type() functions for config
CONFIG_BOARD_TYPES.
This is useful in case of running many boards with just one config.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change adds declaration of functions:
- set_board_type() - called at board_early_init_f()
- get_board_type() - called at checkboard()
For supporting multiple board types in a one config - it is welcome
to display the current board model. This is what get_board_type()
should return.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change enable automatic setting of dfu alt info
on every boot. This is useful in case of booting one
u-boot binary from multiple media.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change introduces new common function:
- set_dfu_alt_info() - put dfu system and bootloader setting
into $dfu_alt_info.
functions declaration:
- char *get_dfu_alt_system(void)
- char *get_dfu_alt_boot(void)
- void set_dfu_alt_info(void)
and new config:
- CONFIG_SET_DFU_ALT_INFO
This function can be used for auto setting dfu configuration on boot.
Such feature is useful for multi board support by one u-boot binary.
Each board should define two functions:
- get_dfu_alt_system()
- get_dfu_alt_boot()
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
It is possible to boot device using a micro SD or eMMC slots.
In this situation, boot device should be registered as a block
device 0 in the MMC framework, because CONFIG_SYS_MMC_ENV_DEV
is usually set to "0" in the most config cases.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The byte order of soc revision was inverted, now it is fixed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The help message in board/ti/am335x/Kconfig says AM335x has
6 UARTs, so the valid number for CONFIG_CONS_INDEX is from 1 to 6.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
The QS Systems TQMa6 board support was added by commit cb07d74e
and lost by commit e82abaeb.
Commit e82abaeb merged the IMX branch based on pre-Kconfig
and the mainline based on post-Kconfig, simply deleting
the boards.cfg file. As a result, some boards added just before
the merge were lost.
This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board
to work on the Kconfig infrastructure.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Nomadik board select menu to nomadik/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="nomadik").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Orion5x board select menu to orion5x/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="orion5x").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Keystone board select menu to keystone/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="keystone").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP5 board select menu to omap5/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap5").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP4 board select menu to omap4/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap4").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP3 board select menu to omap3/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap3
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Davinci board select menu to davinci/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="davinci").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Exynos board select menu to exynos/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="exynos").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Prafulla Wadasdkar <prafulla@marvell.com>
Cc: Luka Perkov <luka@openwrt.org>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Rmobile board select menu to rmobile/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="rmobile").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.
Insert the Tegra SoC select menu between the arch select and the
board select.
Architecture select
|-- Tegra Platform (Tegra)
|- Tegra SoC select (Tegra20 / 30 / 114 / 124)
|- Board select
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:
config TEGRA
bool
select SPL
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Zynq board select menu to zynq/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="zynq").
Refactor board/xilinx/zynq/MAINTAINERS too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Commit 41623c9 'arm: move exception handling out of start.S files' missed some
linker scripts. Hence, some boards no longer had exception handling linked since
this commit. Restore the original behavior by adding the .vectors section to
these linker scripts.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
The bcm_ep board configuration is used by a number of boards
including Cygnus and NSP.
Add builds for the bcm958300k and the bcm958622hr boards.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
The email address of Matt Waddel is no longer working.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alexei Fedorov <alexie.fedorov@arm.com>
To enable hypervisors utilizing the ARMv7 virtualization extension
on the Arndale board, add the simple SMP pen address writer function
and add the required configuration variables to switch all cores to
HYP mode before launching the OS.
This allows booting KVM and Xen directly from u-boot.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
However ep9315 don't use
interrupt vectors during startup, but _startup symbol is used inside uboot to
calculate actual monitor size.
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
Enable initialization fo designware ethernet controller. With this
patch, ethernet works in my configuration, provided I set ethernet
address in the environment.
Signed-off-by: Pavel Machek <pavel@denx.de>
Though nios2-generic board meant to be a template, it is helpful
to be able to test on a real hardware. As the nios2 linux is
developed and tested on a 3c120 FPGA based Golden Hardware Reference
Design, it makes sense to rebase nios2-generic on this FPGA design.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
This patch changes the link script to base at CONFIG_SYS_MONITOR_BASE.
Then we can remove the text_base hook in nios2-generic board.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
To fix the build error when build for Altera dev kit, not
virtual target. At same time, set the build for Altera dev
kit as default instead virtual target. With that, U-Boot
is booting well and SPL still lack of few drivers.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Initialization of pointer from integer shall be designated by explicit
type cast.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
resync ubi subsystem with linux:
commit 455c6fdbd219161bd09b1165f11699d6d73de11c
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Mar 30 20:40:15 2014 -0700
Linux 3.14
A nice side effect of this, is we introduce UBI Fastmap support
to U-Boot.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Joerg Krause <jkrause@posteo.de>
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- Drop CONFIG_SERIAL[1-6] and use CONFIG_CONS_INDEX tests instead
- Add choice and help text to board/ti/am335x/Kconfig
- Correct comment about IDK in board/ti/am335x/mux.c
- Remove am335x_evm_uart* defconfig files as they're just variations
on a config option now.
Signed-off-by: Tom Rini <trini@ti.com>
Boot from eMMC boot partition corresponds to BOOT_DEVICE_MMC2
omap_bootmode, while BOOT_DEVICE_MMC2_2 corresponds to the user
data partition boot.
Fix mmc_get_env_part() boot mode check to use a correct value.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Fix cl_eeprom_read_mac_addr() return value check.
Fix long line codding style issue in board_init().
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
This patch reads EFUSE_BOOTROM register to see the maximum supported
clock for CORE and TETRIS PLLs and configure them accordingly.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.
As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
SW5.1 (NAND_BOOTn) = OFF (logic-1)
SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)
And also set appropriate SYSBOOT configurations:
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */
Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
This patch adds support for NAND device connected to GPMC chip-select on
following AM43xx EVM boards.
am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a
time either eMMC or NAND can be enabled. Selection between eMMC and NAND is
controlled by:
(a) Statically using Jumper on connecter (J89) present on board.
(a) If Jumper on J89 is NOT used, then selection can be dynamically controlled
by driving SPI2_CS0[MUX_MODE=GPIO] pin via software:
SPI2_CS0 == 0: NAND (default)
SPI2_CS0 == 1: eMMC
am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI,
Thus only one of the two can be used at a time. Selection is controlled by:
(a) Dynamically driving following GPIO pin from software
GPMC_A0(GPIO) == 0 NAND is selected (default)
NAND device (MT29F4G08AB) on these boards has:
- data-width=8bits
- blocksize=256KB
- pagesize=4KB
- oobsize=224 bytes
For above NAND device, ROM code expects the boot-loader to be flashed in BCH16
ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs.
Signed-off-by: Pekon Gupta <pekon@ti.com>
This patch adds support of NOR cape[1] for both Beaglebone (white) and
Beaglebone(Black) boards. NOR Flash on this cape is connected to GPMC
chip-select[0] and accesses as external memory-mapped device.
This cape has 128Mbits(16MBytes), x16, CFI compatible NOR Flash device.
As GPMC chip-select[0] can be shared by multiple capes so NOR profile is
not enabled by default in boards.cfg. Following changes are required to
enable NOR cape detection when building am335x_boneblack board profile.
Signed-off-by: Tom Rini <trini@ti.com>
Beaglebone Board can be connected to expansion boards to add devices to them.
These expansion boards are called 'capes'. This patch adds support for
following versions of Beaglebone(AM335x) NAND capes
(a) NAND Device with bus-width=16, block-size=128k, page-size=2k, oob-size=64
(b) NAND Device with bus-width=16, block-size=256k, page-size=4k, oob-size=224
Further information and datasheets can be found at [1] and [2]
* How to boot from NAND using Memory Expander + NAND Cape ? *
- Important: As BOOTSEL values are sampled only at POR, so after changing any
setting on SW2 (DIP switch), disconnect and reconnect all board power supply
(including mini-USB console port) to POR the beaglebone.
- Selection of ECC scheme
for NAND cape(a), ROM code expects BCH8_HW ecc-scheme
for NAND cape(b), ROM code expects BCH16_HW ecc-scheme
- Selction of boot modes can be controlled via DIP switch(SW2) present on
Memory Expander cape.
SW2[SWITCH_BOOT] == OFF follow default boot order MMC-> SPI -> UART -> USB
SW2[SWITCH_BOOT] == ON boot mode selected via DIP switch(SW2)
So to flash NAND, first boot via MMC or other sources and then switch to
SW2[SWITCH_BOOT]=ON to boot from NAND Cape.
- For NAND boot following switch settings need to be followed
SW2[ 1] = OFF (SYSBOOT[ 0]==1: NAND boot mode selected )
SW2[ 2] = OFF (SYSBOOT[ 1]==1: -- do -- )
SW2[ 3] = ON (SYSBOOT[ 2]==0: -- do -- )
SW2[ 4] = ON (SYSBOOT[ 3]==0: -- do -- )
SW2[ 5] = OFF (SYSBOOT[ 4]==1: -- do -- )
SW2[ 6] = OFF (SYSBOOT[ 8]==1: 0:x8 device, 1:x16 device )
SW2[ 7] = ON (SYSBOOT[ 9]==0: ECC done by ROM )
SW2[ 8] = ON (SYSBOOT[10]==0: Non Muxed device )
SW2[ 9] = ON (SYSBOOT[11]==0: -- do -- )
[1] http://beagleboardtoys.info/index.php?title=BeagleBone_Memory_Expansion
[2] http://beagleboardtoys.info/index.php?title=BeagleBone_4Gb_16-Bit_NAND_Module
*IMPORTANT NOTE*
As Beaglebone board shares the same config as AM335x EVM, so following
changes are required in addition to this patch for Beaglebone NAND cape.
(1) Enable NAND in am335x_beaglebone board profile
(2) Add CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config because:
- AM335x EVM has NAND device with datawidth=8, whereas
- Beaglebone NAND cape has NAND device with data-width=16
Emails to Sandeep Paulraj <s-paulraj@ti.com>
have been bouncing.
Please assign new maintainer(s) to get these boards
back to Maintained.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Emails to the board maintainer
"Rishi Bhattacharya <rishi@ti.com>"
have been bouncing.
Tom suggested to remove this board.
Remove also omap1510_udc.c because this is the last board
to enable it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
There is the requirement on the chassis's backplane that when the clocks
have been enabled, they then should not disappear.
Resetting the Zarlink clocking chips at unit reset violates this
requirement because the backplane clocks are not supplied during the
reset time.
To avoid this side effect, both the Zarlink clocking chips are reset
only at power up.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
XFI is supported on T4QDS-XFI board, which removed slot3, and four LANEs
of serdes2 are routed to a SFP+ cages, which to house fiber cable or
direct attach cable(copper), the copper cable is used to emulate the
10GBASE-KR scenario.
So, for XFI usage, there are two scenarios, one will use fiber cable,
another will use copper cable. For fiber cable, there is NO PHY, while
for copper cable, we need to use internal PHY which exist in Serdes to
do auto-negotiation and link training, which implemented in kernel.
We use hwconfig to define cable type for XFI, and fixup dtb based on the
cable type.
For copper cable, set below env in hwconfig:
fsl_10gkr_copper:<10g_mac_name>
the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2. The
four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports,
if a given 10G port will use the copper cable for 10GBASE-KR, set the
<10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be
assumed to be used for the port.
For ex. if four XFI ports will both use copper cable, the hwconfig
should contain:
fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm2_10g1,fm2_10g2
For fiber cable:
1. give PHY address to a XFI port, otherwise, the XFI ports will not be
available in U-boot, there is no PHY physically for XFI when using fiber
cable, this is just to make U-boot happy and we can use the XFI ports
in U-boot.
2. fixup dtb to use fixed-link in case of fiber cable which has no PHY.
Kernel requests that a MAC must have a PHY or fixed-link.
When using XFI protocol, the MAC 9/10 on FM1 should init as 10G interface.
Change serdes 2 protocol 56 to 55 which has same feature as 56 since 56
is not valid any longer.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031.
Add support for one FEC port initially.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6sxsabresd was not in the master branch when the conversion to the new Kconfig
style happened, so convert it now so that it can build again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Nikita Kiryanov
Fabio Estevam
Tom Rini
Soren Brinkmann
Wolfgang Denk
Nobuhiro Iwamatsu
Marek Vasut
Igor Grinberg
Heiko Schocher
Khoronzhuk, Ivan
Hao Zhang
Simon Glass
Ian Campbell
Chen-Yu Tsai
Masahiro Yamada
Ye.Li
Daniel Schwierzeck
Przemyslaw Marczak
Nikolay Dimitrov
Christian Gmeiner
Markus Niebel
Georges Savoundararadj
Matthias Fuchs
Stefan Roese
Albert ARIBAUD
Anatolij Gustschin
Jeroen Hofstee
Hans de Goede
Maxime Ripard
Iain Paton
Stefan Herbrechtsmeier
Vitaly Andrianov
Stephen Warren
Robert Baldyga
Marcel Ziswiler
Stephen Warren
Eric Nelson
Ruchika Gupta
Andreas Bießmann
Hannes Petermaier
David Müller (ELSOFT AG)
Alexander Kochetkov
Roger Quadros
Anthony Felice
Minkyu Kang
Robert Winkler
Troy Kisky
Pavel Machek
York Sun
Priyanka Jain
vijay rai
Prabhakar Kushwaha
Nitin Garg
Stefano Babic
Jagannadha Sutradharudu Teki
Bo Shen
Murali Karicheri
Stefan Agner
Thierry Reding
Tim Harvey
Wang Huan
Claudiu Manoil
Ajay Kumar
FUKAUMI Naoki
Benoît Thébaudeau
Steve Rae
Scott Branden
Andre Przywara
Sergey Kostanbaev
Thomas Chou
Chin Liang See
Vasili Galka
Lokesh Vutla
Dmitry Lifshitz
pekon gupta
Valentin Longchamp
Shaohui Xie