We should use unified setup_ddr_tlbs() for spl boot and non-spl boot
to make sure 'M' bit is set for DDR TLB to maintain cache coherence.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For malloc to work in SPL framework enable GD_FLG_FULL_MALLOC_INIT
flag in global data after allocating memory using mem_malloc_init.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
These functions are part of the Linux 4.6 sync. They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
QorIQ LS1012A FREEDOM (LS1012AFRDM) is a high-performance
development platform, with a complete debugging environment.
The LS1012AFRDM board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Development System (LS1012AQDS) is a high-performance
development platform, with a complete debugging environment.
The LS1012AQDS board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add QIXIS_LBMAP_BRDCFG_REG to the save offset of LBMAP
configuration register instead of hardcoding it in
set_lbmap() function.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Check if qixis supports memory-mapped read/write
before compiling IFC based qixis read/write functions.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SoC overviews are getting repeated across board folders.
So, Organize SoC overview at common location i.e. fsl-layerscape/doc
Also move README.lsch2 and README.lsch3 in same folder.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SCFG_USBPWRFAULT_DEDICATED instead of SCFG_USBPWRFAULT_SHARED should
be used for USB 3 & 2.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS102A ref manual dictates that ICID have to be written to the MSB
of the ICID register, not to the LSB.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
This patch updates clk_adjust to actual value for boards with
T-series and LS-series SoCs to match the setting of clk_adjust
in latest ddr driver.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
BOOTCFG_RSTMUX8 register controls the reset mux associated with the ARM.
Timer5(dedicated to ARM) when used as WatchDog timer, the events it
generates are routed to the above mux.
Following are the 3 events that can controlled bt the reset mux:
- Device Reset
- An interrupt to the ARM_GIC
- An interrupt to the ARM_GIC followed by a device reset.
Right now to give a default watchdog behaviour "Device reset" is
being selected.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Currently omap_vcores is wrongly assigned a default value of
beagle_x15_volts. Hence populating a new structure for am572x-idk
and assigning it to omap_vcores in the vcores_init function.
Fixes: c020d355c4 ("board: ti: am57xx: Add support for am572x idk in SPL")
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
The voltage values for each voltage domain at an OPP is identical
across all the SoCs in the DRA7 family. The current code defines
one set of macros for DRA75x/DRA74x SoCs and another set for DRA72x
macros. Consolidate both these sets into a single set.
This is done so as to minimize the number of macros used when voltage
values will be added for other OPPs as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Define a set of common macros for the efuse register offsets
(different for each OPP) that are used to get the AVS Class 0
voltage values and ABB configuration values. Assign these
common macros to the register offsets for OPP_NOM by default
for all voltage domains. These common macros can then be
redefined properly to point to the OPP specific efuse register
offset based on the desired OPP to program a specific voltage
domain.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
CONFIG_USB_XHCI_OMAP can be set for host mode without setting
CONFIG_USB_DWC3 which is meant for gadget mode only.
board_usb_init() was not being defined for CONFIG_USB_XHCI_OMAP
resulting in a data abort on usb start.
Define board_usb_init() for CONFIG_USB_XHCI_OMAP case. Move
gadget specific handling to within CONFIG_USB_DWC3.
Fixes: 6f1af1e358 ("board: ti: invoke clock API to enable and disable clocks")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Add support for board based on the popular Altera Cyclone V SoC.
This board has the following properties:
- 1 GiB of DRAM
- 1 Gigabit ethernet
- 1 USB gadget port
- 1 USB host port with an on-board hub
- 2 QSPI NORs connected to the Cadence QSPI core
- Multiple I2C EEPROMs and one I2C temperature sensor
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
---
V2: Update the defconfig as per Tom's request
P2771-0000 is a P3310 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB micro-B
port, Ethernet, USB3 host port, SATA, PCIe, and two GPIO expansion
headers.
Currently, due to U-Boot's level of support for Tegra186, the only
features supported by U-Boot are the console UART and the on-board eMMC.
Additional features will be added over time.
U-Boot has so far been tested by replacing the kernel image on the device
with a U-Boot binary. It is anticipated that U-Boot will eventually
replace the CCPLEX bootloader binary, as on previous chips. This hasn't
yet been tested.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There are currently many places that define the list of all Tegra GPIOs;
the DT binding header and custom Tegra-specific header file gpio.h. Fix
the redundancy by replacing everything with the DT binding header file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In 'commit d584c68ce0f5bf2f430ccfb2ba00bd506206fb91',
ar8031 is changed to use ar8035_config. ar8035_config
actually does the same thing as mx6_rgmii_rework, so
drop mx6_rgmii_rework and board_phy_config.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
UHS-I support is available on Ventana boards with micro-SD sockets depending
on the board revision. For backwards compatibility to not break users
who have old bootloaders and newer kernels the device-tree on boards with
microSD disables UHS-I support by default by defining the no-1-8-v property
in the esdhc controller node. For models/revisions that support switchable
1.8V/3.3V I/O which is detectable by the presence of a pull-down on the
SD3_VSELECT pin we remove that property to enable support in the kernel.
Additionally we add SD3_VSELECT to the pinmux for clarity (even though U-Boot
does not currently support UHS-I modes requiring 1.8V I/O).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Removed several EEPROM bit dependencies:
- for dt aliases that don't exist and thus don't ever do anything
(pcie,lvds1,uart*,vpu,csi*,hdmi_in,hdmi_out,cvbs_in,cvbs_out,gps)
- for features that don't effect bus ordering or have no detrimental affect
if erroneously enabled when not present (ahci,nand,i2c*)
- for features that have little to no impact on being erroneously enabled
but high impact if erroneously disabled (can*, spi*)
- for features that have an high adverse affect of not being set when they
should and no adverse affect of being set when they
shouldn't (ipu*).
Removing these means the following:
- these no longer are supported with the econfig command
- these no longer affect the device-tree in any way
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The MSATA feature is a board-specific feature on Gateworks Ventana boards.
In most cases a 2:1 mux will steer either PCIe or SATA to a miniPCIe socket
through an MSATA_EN gpio. In these such cases assign the gpio in the board
specific struct and use its presence to determine if we default the GPIO to
PCIe and if we later steer it according to hwconfig.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Most Ventana boards have a connector with off-board digital-I/O signals
including some that can be pinmuxed as either a PWM or a GPIO. The hwconfig
env variable is used to configure these and they will be pinmuxed according
to this configuration in the bootloader.
This patch adds a device-tree fixup that will enable the pwm controller
nodes appropriately for digital-I/O's that are configured as pwm via hwconfig
so that the pin can be used with the Linux kernel /sys/class/pwm API.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Calling request_gpio to register bklt_gpio with the GPIO driver had no effect
in setup_display called from early board init (although pinmuxing it and
configuring it as output-low does do what it should). Therefore move the
request_gpio later in enable_lvds so that its registered for use by the
gpio command if LVDS is actually enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks System Controller on Ventana boards has the ability to
disable the board's primary power supply until the RTC hits a specific
time. When sleeping a button-down event on the GSC user pushbutton will
wake the board before it's wake time has been reached. This feature is
referred to as GSC sleep.
Add a command to invoke sleep mode for a specified number of seconds.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
If not booting Falcon mode, leave the boot watchdog enabled as a work-around
for other non-resolved bootloader hangs.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Allow L1 Icache & L1 Dcache line size to be specified separately, since
there's no architectural mandate that they be the same. The
[id]cache_line_size functions are tidied up to take advantage of the
fact that the Kconfig entries are always present to simply check them
for zero rather than needing to #ifdef on their presence.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
[removed CONFIG_SYS_CACHELINE_SIZE in include/configs/pic32mzdask.h]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Move details of the L1 cache line sizes & total sizes into Kconfig,
defaulting to 0. A new CONFIG_SYS_CACHE_SIZE_AUTO Kconfig entry is
introduced to allow platforms to select auto-detection of cache sizes,
and it defaults to being enabled if none of the cache sizes are set by
the configuration (ie. sizes are all the default 0), and code is
adjusted to #ifdef on that rather than on the definition of the sizes
(which will always be defined even if 0).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Both real Malta boards & emulators that mimic Malta (eg. QEMU) can
support MIPS64 CPUs. Allow MIPS64 builds of U-Boot for such boards,
which enables the user to make use of the whole 64 bit address space.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
As the old ethernet PHY is not available any more, the x600 board has
been redesigned with the Micrel KSZ9031 PHY. This patch adds support
to autodetect the PHY and configure the Micrel PHY correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Different AM335x based platforms have different serial consoles. As serial
console is Kconfig option a separate defconfig has to be created for each
platform. So pass the serial device dynamically.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add minimal dts support for AM335x-ICEv2 board
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
In order to enable cpsw on AM335x ICEv2 board, the following needs to be done:
1)There are few on board jumper settings which gives a choice between
cpsw and PRUSS, that needs to be properly selected[1]. Even after selecting
this, there are few GPIOs which control these muxes that needs to be held high.
2) The clock to PHY is provided by a PLL-based clock synthesizer[2] connected
via I2C. This needs to properly programmed and locked for PHY operation.
And PHY needs to be reset before before being used, which is also held by
a GPIO.
3) RMII mode needs to be selected.
[1] http://www.ti.com/lit/zip/tidr336
[2] http://www.ti.com/lit/ds/symlink/cdce913.pdf
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM335x ICEv2 contains a 2Gbit(128Mx16) of DDR3 SDRAM(MT41J128M16JT-125),
capable of running at 400MHz. Adding this specific DDR configuration
details running at 400MHz.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Similar to other TI's AM335x platforms, AM335x ICEv2 also has an
eeprom populated for its unique identification. Adding this info
so that AM335x ICEv2 specific initialization can be done.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use a single defconfig for all AM335x platforms by enabling FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use a single defconfig for all AM43xx platforms by enabling FIT and delete
the platform specific defconfigs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Removing:
uart3_defconfig:
Now uart3 can be selected using menuconfig, removing separate
config for uart mode. Doing uart boot is not straight forward as ROM uses
uart3 as default serial console. In order to boot to prompt, concole in both
u-boot and kernel needs to be changed.
qspiboot_defconfig:
The only advantage of enabling QSPI_BOOT is selecting env in QSPI.
Eventually env needs to be selected by menuconfig so removing
qspiboot_defconfig. qspiboot can be done using dra7xx_evm_defconfig.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use a single defconfig for all DRA7 platforms by enabling FIT and delete
the platform specific defconfigs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Adds the board specific ft_board_setup() functions that
are called when CONFIG_OF_BOARD_SETUP is defined. These functions
will currently just call the ft_cpu_setup() function.
Adds CONFIG_OF_BOARD_SETUP to the defconfig files
for dra72_evm, dra74_evm, and am57xx_evm.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds code to detect AM43xx HS EVMS - the string in the
I2C EEPROM for HS EVMs differs from GP EVMs. Adds code to
for evm detection, regardless of whether the evm is for
GP or HS parts, and updates board init to use that.
Modifies findfdt command to pick up am437x-gp-evm.dtb for
the HS EVMs also, as the boards are similar except for
some security specific changes around power supply and
enclosure protection.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since CONFIG_OF_BOARD_SETUP depends on CONFIG_OF_LIBFDT:
config OF_BOARD_SETUP
bool "Set up board-specific details in device tree before boot"
depends on OF_LIBFDT
...
remove superfluous tests of CONFIG_OF_LIBFDT when testing for
CONFIG_OF_BOARD_SETUP.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[trini: Typo fix: s/ifdefi/ifdef/]
Signed-off-by: Tom Rini <trini@konsulko.com>
With dropping support for some boards and the deletion of some source
files, it appears that both of these directories are now superfluous.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
This includes the following fixes:
- Define needed __init_end symbol - see initr_reloc_global_data()
- Drop SH-specific struct bd_info
- Add an empty relocate_code() function
This prevents build errors with generic board, but the code will still need
work. Perhaps this is a better alternative than deleting the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the warning from the Makefile, since boards that do not use generic
board will no longer build. Also update documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].
[1] https://patchwork.ozlabs.org/patch/603583/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move CONFIG_SYS_TEXT_BASE to Kconfig, and add default values in board
Kconfig files matching what was present in their config headers. This
will make it cleaner to conditionalise the value for Malta based on 32
vs 64 bit builds.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The address of the UART differs based upon the system controller because
it's actually within the I/O port region, which is in a different
location for each system controller. Rather than handling this as 2
UARTs with the correct one selected at runtime, use I/O port accessors
for the UART such that access to it gets translated into the I/O port
region automatically.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.
Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The ARM Trusted Firmware (ATF) code now lives in SRAM on the Pine64/A64,
so we can claim the whole of DRAM for OS use.
This reverts commit 3ffe39ed2b.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A80 uses the AXP809 as its primary PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The AXP818 has a switchable output, SW. This is commonly used for
controlling power to the LCD backlight.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The newer chips use a newer display pipeline, which is not supported.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A83T, H3, and A64 have a dedicated pin for card detect on the PF
pingroup. This is used in all designs. Set it as the default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In most other places, we sort SoC descriptions by family (sunXi) first,
then by the chip name (A20).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The user should always select an SoC variant to support. Not choosing
one doesn't make sense for a bootloader.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we are using driver model, we can drop the weak functions and LCD
init in the board file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Update several boards to use driver model for video. This involves changes
to the EDP and FIMD (frame buffer) drivers. Existing PWM, simple-panel and
pwm-backlight drivers are used. These work without additional configuration
since they use the device tree settings in the same way as Linux.
Boards converted are:
- snow
- spring
- peach-pit
- peach-pi
All have been tested. Not converted:
- MIPI display driver
- s5pc210_universal
- smdk5420
- smdk5250
- trats
- trats2
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This function controls enabling the EDP PHY. Rename it and drop the existing
weak functions, which are confusing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some boards have the LCD enabled but I cannot test operation for the driver
model conversion. Disable the LCD on these to avoid build errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This file currently requires LCD support. Adjust it so that it can still be
built without LCD support (even thought it won't work fully).
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Espresso7420 is a development/evaluation board for Exynos7420 SoC. It
includes multiple onboard compoments (EMMC/Codec) and various
interconnects (USB/HDMI).
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Disable the non-existent ethernet ports on T4240RDB:FM1_DTSEC5,
FM1_DTSEC6, FM2_DTSEC5 and FM2_DTSEC6.
Signed-off-by: Ying Zhang <ying.zhang22455@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NAND+MMC env support costs 12KB in the SPL which is fairly expensive just
for the ability to specify whether or not to boot to uboot or directly
to linux. The Ventana boards have plenty of EEPROM storage so we will use
a byte there to signify if we should boot to the bootloader or to the OS.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Shengzhou Liu
Sumit Garg
Scott Wood
Prabhakar Kushwaha
Abhimanyu Saini
Shaohui Xie
York Sun
Vincent Siles
Tom Rini
Lokesh Vutla
Keerthy
Anna, Suman
Roger Quadros
Marek Vasut
Stephen Warren
Sebastien Bourdelin
Peng Fan
Tim Harvey
Wills Wang
Paul Burton
Stefan Roese
Bin Meng
Daniel Allred
Madan Srinivas
Robert P. J. Day
Simon Glass
Beniamino Galvani
Hans de Goede
Andre Przywara
Chen-Yu Tsai
Thomas Abraham
Ying Zhang