1007 lines
27 KiB
C
1007 lines
27 KiB
C
// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
|
|
//
|
|
// This file is provided under a dual BSD/GPLv2 license. When using or
|
|
// redistributing this file, you may do so under either license.
|
|
//
|
|
// Copyright(c) 2018 Intel Corporation. All rights reserved.
|
|
//
|
|
// Authors: Liam Girdwood <liam.r.girdwood@linux.intel.com>
|
|
// Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
|
|
// Rander Wang <rander.wang@intel.com>
|
|
// Keyon Jie <yang.jie@linux.intel.com>
|
|
//
|
|
|
|
/*
|
|
* Hardware interface for generic Intel audio DSP HDA IP
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <sound/hdaudio_ext.h>
|
|
#include <sound/hda_register.h>
|
|
#include "../sof-audio.h"
|
|
#include "../ops.h"
|
|
#include "hda.h"
|
|
#include "hda-ipc.h"
|
|
|
|
static bool hda_enable_trace_D0I3_S0;
|
|
#if IS_ENABLED(CONFIG_SND_SOC_SOF_DEBUG)
|
|
module_param_named(enable_trace_D0I3_S0, hda_enable_trace_D0I3_S0, bool, 0444);
|
|
MODULE_PARM_DESC(enable_trace_D0I3_S0,
|
|
"SOF HDA enable trace when the DSP is in D0I3 in S0");
|
|
#endif
|
|
|
|
/*
|
|
* DSP Core control.
|
|
*/
|
|
|
|
static int hda_dsp_core_reset_enter(struct snd_sof_dev *sdev, unsigned int core_mask)
|
|
{
|
|
u32 adspcs;
|
|
u32 reset;
|
|
int ret;
|
|
|
|
/* set reset bits for cores */
|
|
reset = HDA_DSP_ADSPCS_CRST_MASK(core_mask);
|
|
snd_sof_dsp_update_bits_unlocked(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS,
|
|
reset, reset);
|
|
|
|
/* poll with timeout to check if operation successful */
|
|
ret = snd_sof_dsp_read_poll_timeout(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS, adspcs,
|
|
((adspcs & reset) == reset),
|
|
HDA_DSP_REG_POLL_INTERVAL_US,
|
|
HDA_DSP_RESET_TIMEOUT_US);
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev,
|
|
"error: %s: timeout on HDA_DSP_REG_ADSPCS read\n",
|
|
__func__);
|
|
return ret;
|
|
}
|
|
|
|
/* has core entered reset ? */
|
|
adspcs = snd_sof_dsp_read(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS);
|
|
if ((adspcs & HDA_DSP_ADSPCS_CRST_MASK(core_mask)) !=
|
|
HDA_DSP_ADSPCS_CRST_MASK(core_mask)) {
|
|
dev_err(sdev->dev,
|
|
"error: reset enter failed: core_mask %x adspcs 0x%x\n",
|
|
core_mask, adspcs);
|
|
ret = -EIO;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int hda_dsp_core_reset_leave(struct snd_sof_dev *sdev, unsigned int core_mask)
|
|
{
|
|
unsigned int crst;
|
|
u32 adspcs;
|
|
int ret;
|
|
|
|
/* clear reset bits for cores */
|
|
snd_sof_dsp_update_bits_unlocked(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS,
|
|
HDA_DSP_ADSPCS_CRST_MASK(core_mask),
|
|
0);
|
|
|
|
/* poll with timeout to check if operation successful */
|
|
crst = HDA_DSP_ADSPCS_CRST_MASK(core_mask);
|
|
ret = snd_sof_dsp_read_poll_timeout(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS, adspcs,
|
|
!(adspcs & crst),
|
|
HDA_DSP_REG_POLL_INTERVAL_US,
|
|
HDA_DSP_RESET_TIMEOUT_US);
|
|
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev,
|
|
"error: %s: timeout on HDA_DSP_REG_ADSPCS read\n",
|
|
__func__);
|
|
return ret;
|
|
}
|
|
|
|
/* has core left reset ? */
|
|
adspcs = snd_sof_dsp_read(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS);
|
|
if ((adspcs & HDA_DSP_ADSPCS_CRST_MASK(core_mask)) != 0) {
|
|
dev_err(sdev->dev,
|
|
"error: reset leave failed: core_mask %x adspcs 0x%x\n",
|
|
core_mask, adspcs);
|
|
ret = -EIO;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int hda_dsp_core_stall_reset(struct snd_sof_dev *sdev, unsigned int core_mask)
|
|
{
|
|
/* stall core */
|
|
snd_sof_dsp_update_bits_unlocked(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS,
|
|
HDA_DSP_ADSPCS_CSTALL_MASK(core_mask),
|
|
HDA_DSP_ADSPCS_CSTALL_MASK(core_mask));
|
|
|
|
/* set reset state */
|
|
return hda_dsp_core_reset_enter(sdev, core_mask);
|
|
}
|
|
|
|
static bool hda_dsp_core_is_enabled(struct snd_sof_dev *sdev, unsigned int core_mask)
|
|
{
|
|
int val;
|
|
bool is_enable;
|
|
|
|
val = snd_sof_dsp_read(sdev, HDA_DSP_BAR, HDA_DSP_REG_ADSPCS);
|
|
|
|
#define MASK_IS_EQUAL(v, m, field) ({ \
|
|
u32 _m = field(m); \
|
|
((v) & _m) == _m; \
|
|
})
|
|
|
|
is_enable = MASK_IS_EQUAL(val, core_mask, HDA_DSP_ADSPCS_CPA_MASK) &&
|
|
MASK_IS_EQUAL(val, core_mask, HDA_DSP_ADSPCS_SPA_MASK) &&
|
|
!(val & HDA_DSP_ADSPCS_CRST_MASK(core_mask)) &&
|
|
!(val & HDA_DSP_ADSPCS_CSTALL_MASK(core_mask));
|
|
|
|
#undef MASK_IS_EQUAL
|
|
|
|
dev_dbg(sdev->dev, "DSP core(s) enabled? %d : core_mask %x\n",
|
|
is_enable, core_mask);
|
|
|
|
return is_enable;
|
|
}
|
|
|
|
int hda_dsp_core_run(struct snd_sof_dev *sdev, unsigned int core_mask)
|
|
{
|
|
int ret;
|
|
|
|
/* leave reset state */
|
|
ret = hda_dsp_core_reset_leave(sdev, core_mask);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* run core */
|
|
dev_dbg(sdev->dev, "unstall/run core: core_mask = %x\n", core_mask);
|
|
snd_sof_dsp_update_bits_unlocked(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS,
|
|
HDA_DSP_ADSPCS_CSTALL_MASK(core_mask),
|
|
0);
|
|
|
|
/* is core now running ? */
|
|
if (!hda_dsp_core_is_enabled(sdev, core_mask)) {
|
|
hda_dsp_core_stall_reset(sdev, core_mask);
|
|
dev_err(sdev->dev, "error: DSP start core failed: core_mask %x\n",
|
|
core_mask);
|
|
ret = -EIO;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* Power Management.
|
|
*/
|
|
|
|
static int hda_dsp_core_power_up(struct snd_sof_dev *sdev, unsigned int core_mask)
|
|
{
|
|
unsigned int cpa;
|
|
u32 adspcs;
|
|
int ret;
|
|
|
|
/* update bits */
|
|
snd_sof_dsp_update_bits(sdev, HDA_DSP_BAR, HDA_DSP_REG_ADSPCS,
|
|
HDA_DSP_ADSPCS_SPA_MASK(core_mask),
|
|
HDA_DSP_ADSPCS_SPA_MASK(core_mask));
|
|
|
|
/* poll with timeout to check if operation successful */
|
|
cpa = HDA_DSP_ADSPCS_CPA_MASK(core_mask);
|
|
ret = snd_sof_dsp_read_poll_timeout(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS, adspcs,
|
|
(adspcs & cpa) == cpa,
|
|
HDA_DSP_REG_POLL_INTERVAL_US,
|
|
HDA_DSP_RESET_TIMEOUT_US);
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev,
|
|
"error: %s: timeout on HDA_DSP_REG_ADSPCS read\n",
|
|
__func__);
|
|
return ret;
|
|
}
|
|
|
|
/* did core power up ? */
|
|
adspcs = snd_sof_dsp_read(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS);
|
|
if ((adspcs & HDA_DSP_ADSPCS_CPA_MASK(core_mask)) !=
|
|
HDA_DSP_ADSPCS_CPA_MASK(core_mask)) {
|
|
dev_err(sdev->dev,
|
|
"error: power up core failed core_mask %xadspcs 0x%x\n",
|
|
core_mask, adspcs);
|
|
ret = -EIO;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int hda_dsp_core_power_down(struct snd_sof_dev *sdev, unsigned int core_mask)
|
|
{
|
|
u32 adspcs;
|
|
int ret;
|
|
|
|
/* update bits */
|
|
snd_sof_dsp_update_bits_unlocked(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS,
|
|
HDA_DSP_ADSPCS_SPA_MASK(core_mask), 0);
|
|
|
|
ret = snd_sof_dsp_read_poll_timeout(sdev, HDA_DSP_BAR,
|
|
HDA_DSP_REG_ADSPCS, adspcs,
|
|
!(adspcs & HDA_DSP_ADSPCS_CPA_MASK(core_mask)),
|
|
HDA_DSP_REG_POLL_INTERVAL_US,
|
|
HDA_DSP_PD_TIMEOUT * USEC_PER_MSEC);
|
|
if (ret < 0)
|
|
dev_err(sdev->dev,
|
|
"error: %s: timeout on HDA_DSP_REG_ADSPCS read\n",
|
|
__func__);
|
|
|
|
return ret;
|
|
}
|
|
|
|
int hda_dsp_enable_core(struct snd_sof_dev *sdev, unsigned int core_mask)
|
|
{
|
|
struct sof_intel_hda_dev *hda = sdev->pdata->hw_pdata;
|
|
const struct sof_intel_dsp_desc *chip = hda->desc;
|
|
int ret;
|
|
|
|
/* restrict core_mask to host managed cores mask */
|
|
core_mask &= chip->host_managed_cores_mask;
|
|
|
|
/* return if core_mask is not valid or cores are already enabled */
|
|
if (!core_mask || hda_dsp_core_is_enabled(sdev, core_mask))
|
|
return 0;
|
|
|
|
/* power up */
|
|
ret = hda_dsp_core_power_up(sdev, core_mask);
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev, "error: dsp core power up failed: core_mask %x\n",
|
|
core_mask);
|
|
return ret;
|
|
}
|
|
|
|
return hda_dsp_core_run(sdev, core_mask);
|
|
}
|
|
|
|
int hda_dsp_core_reset_power_down(struct snd_sof_dev *sdev,
|
|
unsigned int core_mask)
|
|
{
|
|
struct sof_intel_hda_dev *hda = sdev->pdata->hw_pdata;
|
|
const struct sof_intel_dsp_desc *chip = hda->desc;
|
|
int ret;
|
|
|
|
/* restrict core_mask to host managed cores mask */
|
|
core_mask &= chip->host_managed_cores_mask;
|
|
|
|
/* return if core_mask is not valid */
|
|
if (!core_mask)
|
|
return 0;
|
|
|
|
/* place core in reset prior to power down */
|
|
ret = hda_dsp_core_stall_reset(sdev, core_mask);
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev, "error: dsp core reset failed: core_mask %x\n",
|
|
core_mask);
|
|
return ret;
|
|
}
|
|
|
|
/* power down core */
|
|
ret = hda_dsp_core_power_down(sdev, core_mask);
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev, "error: dsp core power down fail mask %x: %d\n",
|
|
core_mask, ret);
|
|
return ret;
|
|
}
|
|
|
|
/* make sure we are in OFF state */
|
|
if (hda_dsp_core_is_enabled(sdev, core_mask)) {
|
|
dev_err(sdev->dev, "error: dsp core disable fail mask %x: %d\n",
|
|
core_mask, ret);
|
|
ret = -EIO;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
void hda_dsp_ipc_int_enable(struct snd_sof_dev *sdev)
|
|
{
|
|
struct sof_intel_hda_dev *hda = sdev->pdata->hw_pdata;
|
|
const struct sof_intel_dsp_desc *chip = hda->desc;
|
|
|
|
/* enable IPC DONE and BUSY interrupts */
|
|
snd_sof_dsp_update_bits(sdev, HDA_DSP_BAR, chip->ipc_ctl,
|
|
HDA_DSP_REG_HIPCCTL_DONE | HDA_DSP_REG_HIPCCTL_BUSY,
|
|
HDA_DSP_REG_HIPCCTL_DONE | HDA_DSP_REG_HIPCCTL_BUSY);
|
|
|
|
/* enable IPC interrupt */
|
|
snd_sof_dsp_update_bits(sdev, HDA_DSP_BAR, HDA_DSP_REG_ADSPIC,
|
|
HDA_DSP_ADSPIC_IPC, HDA_DSP_ADSPIC_IPC);
|
|
}
|
|
|
|
void hda_dsp_ipc_int_disable(struct snd_sof_dev *sdev)
|
|
{
|
|
struct sof_intel_hda_dev *hda = sdev->pdata->hw_pdata;
|
|
const struct sof_intel_dsp_desc *chip = hda->desc;
|
|
|
|
/* disable IPC interrupt */
|
|
snd_sof_dsp_update_bits(sdev, HDA_DSP_BAR, HDA_DSP_REG_ADSPIC,
|
|
HDA_DSP_ADSPIC_IPC, 0);
|
|
|
|
/* disable IPC BUSY and DONE interrupt */
|
|
snd_sof_dsp_update_bits(sdev, HDA_DSP_BAR, chip->ipc_ctl,
|
|
HDA_DSP_REG_HIPCCTL_BUSY | HDA_DSP_REG_HIPCCTL_DONE, 0);
|
|
}
|
|
|
|
static int hda_dsp_wait_d0i3c_done(struct snd_sof_dev *sdev)
|
|
{
|
|
struct hdac_bus *bus = sof_to_bus(sdev);
|
|
int retry = HDA_DSP_REG_POLL_RETRY_COUNT;
|
|
|
|
while (snd_hdac_chip_readb(bus, VS_D0I3C) & SOF_HDA_VS_D0I3C_CIP) {
|
|
if (!retry--)
|
|
return -ETIMEDOUT;
|
|
usleep_range(10, 15);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int hda_dsp_send_pm_gate_ipc(struct snd_sof_dev *sdev, u32 flags)
|
|
{
|
|
struct sof_ipc_pm_gate pm_gate;
|
|
struct sof_ipc_reply reply;
|
|
|
|
memset(&pm_gate, 0, sizeof(pm_gate));
|
|
|
|
/* configure pm_gate ipc message */
|
|
pm_gate.hdr.size = sizeof(pm_gate);
|
|
pm_gate.hdr.cmd = SOF_IPC_GLB_PM_MSG | SOF_IPC_PM_GATE;
|
|
pm_gate.flags = flags;
|
|
|
|
/* send pm_gate ipc to dsp */
|
|
return sof_ipc_tx_message_no_pm(sdev->ipc, pm_gate.hdr.cmd,
|
|
&pm_gate, sizeof(pm_gate), &reply,
|
|
sizeof(reply));
|
|
}
|
|
|
|
static int hda_dsp_update_d0i3c_register(struct snd_sof_dev *sdev, u8 value)
|
|
{
|
|
struct hdac_bus *bus = sof_to_bus(sdev);
|
|
int ret;
|
|
|
|
/* Write to D0I3C after Command-In-Progress bit is cleared */
|
|
ret = hda_dsp_wait_d0i3c_done(sdev);
|
|
if (ret < 0) {
|
|
dev_err(bus->dev, "CIP timeout before D0I3C update!\n");
|
|
return ret;
|
|
}
|
|
|
|
/* Update D0I3C register */
|
|
snd_hdac_chip_updateb(bus, VS_D0I3C, SOF_HDA_VS_D0I3C_I3, value);
|
|
|
|
/* Wait for cmd in progress to be cleared before exiting the function */
|
|
ret = hda_dsp_wait_d0i3c_done(sdev);
|
|
if (ret < 0) {
|
|
dev_err(bus->dev, "CIP timeout after D0I3C update!\n");
|
|
return ret;
|
|
}
|
|
|
|
dev_vdbg(bus->dev, "D0I3C updated, register = 0x%x\n",
|
|
snd_hdac_chip_readb(bus, VS_D0I3C));
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int hda_dsp_set_D0_state(struct snd_sof_dev *sdev,
|
|
const struct sof_dsp_power_state *target_state)
|
|
{
|
|
u32 flags = 0;
|
|
int ret;
|
|
u8 value = 0;
|
|
|
|
/*
|
|
* Sanity check for illegal state transitions
|
|
* The only allowed transitions are:
|
|
* 1. D3 -> D0I0
|
|
* 2. D0I0 -> D0I3
|
|
* 3. D0I3 -> D0I0
|
|
*/
|
|
switch (sdev->dsp_power_state.state) {
|
|
case SOF_DSP_PM_D0:
|
|
/* Follow the sequence below for D0 substate transitions */
|
|
break;
|
|
case SOF_DSP_PM_D3:
|
|
/* Follow regular flow for D3 -> D0 transition */
|
|
return 0;
|
|
default:
|
|
dev_err(sdev->dev, "error: transition from %d to %d not allowed\n",
|
|
sdev->dsp_power_state.state, target_state->state);
|
|
return -EINVAL;
|
|
}
|
|
|
|
/* Set flags and register value for D0 target substate */
|
|
if (target_state->substate == SOF_HDA_DSP_PM_D0I3) {
|
|
value = SOF_HDA_VS_D0I3C_I3;
|
|
|
|
/*
|
|
* Trace DMA need to be disabled when the DSP enters
|
|
* D0I3 for S0Ix suspend, but it can be kept enabled
|
|
* when the DSP enters D0I3 while the system is in S0
|
|
* for debug purpose.
|
|
*/
|
|
if (!sdev->dtrace_is_supported ||
|
|
!hda_enable_trace_D0I3_S0 ||
|
|
sdev->system_suspend_target != SOF_SUSPEND_NONE)
|
|
flags = HDA_PM_NO_DMA_TRACE;
|
|
} else {
|
|
/* prevent power gating in D0I0 */
|
|
flags = HDA_PM_PPG;
|
|
}
|
|
|
|
/* update D0I3C register */
|
|
ret = hda_dsp_update_d0i3c_register(sdev, value);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/*
|
|
* Notify the DSP of the state change.
|
|
* If this IPC fails, revert the D0I3C register update in order
|
|
* to prevent partial state change.
|
|
*/
|
|
ret = hda_dsp_send_pm_gate_ipc(sdev, flags);
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev,
|
|
"error: PM_GATE ipc error %d\n", ret);
|
|
goto revert;
|
|
}
|
|
|
|
return ret;
|
|
|
|
revert:
|
|
/* fallback to the previous register value */
|
|
value = value ? 0 : SOF_HDA_VS_D0I3C_I3;
|
|
|
|
/*
|
|
* This can fail but return the IPC error to signal that
|
|
* the state change failed.
|
|
*/
|
|
hda_dsp_update_d0i3c_register(sdev, value);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/* helper to log DSP state */
|
|
static void hda_dsp_state_log(struct snd_sof_dev *sdev)
|
|
{
|
|
switch (sdev->dsp_power_state.state) {
|
|
case SOF_DSP_PM_D0:
|
|
switch (sdev->dsp_power_state.substate) {
|
|
case SOF_HDA_DSP_PM_D0I0:
|
|
dev_dbg(sdev->dev, "Current DSP power state: D0I0\n");
|
|
break;
|
|
case SOF_HDA_DSP_PM_D0I3:
|
|
dev_dbg(sdev->dev, "Current DSP power state: D0I3\n");
|
|
break;
|
|
default:
|
|
dev_dbg(sdev->dev, "Unknown DSP D0 substate: %d\n",
|
|
sdev->dsp_power_state.substate);
|
|
break;
|
|
}
|
|
break;
|
|
case SOF_DSP_PM_D1:
|
|
dev_dbg(sdev->dev, "Current DSP power state: D1\n");
|
|
break;
|
|
case SOF_DSP_PM_D2:
|
|
dev_dbg(sdev->dev, "Current DSP power state: D2\n");
|
|
break;
|
|
case SOF_DSP_PM_D3:
|
|
dev_dbg(sdev->dev, "Current DSP power state: D3\n");
|
|
break;
|
|
default:
|
|
dev_dbg(sdev->dev, "Unknown DSP power state: %d\n",
|
|
sdev->dsp_power_state.state);
|
|
break;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* All DSP power state transitions are initiated by the driver.
|
|
* If the requested state change fails, the error is simply returned.
|
|
* Further state transitions are attempted only when the set_power_save() op
|
|
* is called again either because of a new IPC sent to the DSP or
|
|
* during system suspend/resume.
|
|
*/
|
|
int hda_dsp_set_power_state(struct snd_sof_dev *sdev,
|
|
const struct sof_dsp_power_state *target_state)
|
|
{
|
|
int ret = 0;
|
|
|
|
/*
|
|
* When the DSP is already in D0I3 and the target state is D0I3,
|
|
* it could be the case that the DSP is in D0I3 during S0
|
|
* and the system is suspending to S0Ix. Therefore,
|
|
* hda_dsp_set_D0_state() must be called to disable trace DMA
|
|
* by sending the PM_GATE IPC to the FW.
|
|
*/
|
|
if (target_state->substate == SOF_HDA_DSP_PM_D0I3 &&
|
|
sdev->system_suspend_target == SOF_SUSPEND_S0IX)
|
|
goto set_state;
|
|
|
|
/*
|
|
* For all other cases, return without doing anything if
|
|
* the DSP is already in the target state.
|
|
*/
|
|
if (target_state->state == sdev->dsp_power_state.state &&
|
|
target_state->substate == sdev->dsp_power_state.substate)
|
|
return 0;
|
|
|
|
set_state:
|
|
switch (target_state->state) {
|
|
case SOF_DSP_PM_D0:
|
|
ret = hda_dsp_set_D0_state(sdev, target_state);
|
|
break;
|
|
case SOF_DSP_PM_D3:
|
|
/* The only allowed transition is: D0I0 -> D3 */
|
|
if (sdev->dsp_power_state.state == SOF_DSP_PM_D0 &&
|
|
sdev->dsp_power_state.substate == SOF_HDA_DSP_PM_D0I0)
|
|
break;
|
|
|
|
dev_err(sdev->dev,
|
|
"error: transition from %d to %d not allowed\n",
|
|
sdev->dsp_power_state.state, target_state->state);
|
|
return -EINVAL;
|
|
default:
|
|
dev_err(sdev->dev, "error: target state unsupported %d\n",
|
|
target_state->state);
|
|
return -EINVAL;
|
|
}
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev,
|
|
"failed to set requested target DSP state %d substate %d\n",
|
|
target_state->state, target_state->substate);
|
|
return ret;
|
|
}
|
|
|
|
sdev->dsp_power_state = *target_state;
|
|
hda_dsp_state_log(sdev);
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* Audio DSP states may transform as below:-
|
|
*
|
|
* Opportunistic D0I3 in S0
|
|
* Runtime +---------------------+ Delayed D0i3 work timeout
|
|
* suspend | +--------------------+
|
|
* +------------+ D0I0(active) | |
|
|
* | | <---------------+ |
|
|
* | +--------> | New IPC | |
|
|
* | |Runtime +--^--+---------^--+--+ (via mailbox) | |
|
|
* | |resume | | | | | |
|
|
* | | | | | | | |
|
|
* | | System| | | | | |
|
|
* | | resume| | S3/S0IX | | | |
|
|
* | | | | suspend | | S0IX | |
|
|
* | | | | | |suspend | |
|
|
* | | | | | | | |
|
|
* | | | | | | | |
|
|
* +-v---+-----------+--v-------+ | | +------+----v----+
|
|
* | | | +-----------> |
|
|
* | D3 (suspended) | | | D0I3 |
|
|
* | | +--------------+ |
|
|
* | | System resume | |
|
|
* +----------------------------+ +----------------+
|
|
*
|
|
* S0IX suspend: The DSP is in D0I3 if any D0I3-compatible streams
|
|
* ignored the suspend trigger. Otherwise the DSP
|
|
* is in D3.
|
|
*/
|
|
|
|
static int hda_suspend(struct snd_sof_dev *sdev, bool runtime_suspend)
|
|
{
|
|
struct sof_intel_hda_dev *hda = sdev->pdata->hw_pdata;
|
|
const struct sof_intel_dsp_desc *chip = hda->desc;
|
|
#if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
|
|
struct hdac_bus *bus = sof_to_bus(sdev);
|
|
#endif
|
|
int ret, j;
|
|
|
|
hda_sdw_int_enable(sdev, false);
|
|
|
|
/* disable IPC interrupts */
|
|
hda_dsp_ipc_int_disable(sdev);
|
|
|
|
#if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
|
|
hda_codec_jack_wake_enable(sdev, runtime_suspend);
|
|
|
|
/* power down all hda link */
|
|
snd_hdac_ext_bus_link_power_down_all(bus);
|
|
#endif
|
|
|
|
/* power down DSP */
|
|
ret = hda_dsp_core_reset_power_down(sdev, chip->host_managed_cores_mask);
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev,
|
|
"error: failed to power down core during suspend\n");
|
|
return ret;
|
|
}
|
|
|
|
/* reset ref counts for all cores */
|
|
for (j = 0; j < chip->cores_num; j++)
|
|
sdev->dsp_core_ref_count[j] = 0;
|
|
|
|
/* disable ppcap interrupt */
|
|
hda_dsp_ctrl_ppcap_enable(sdev, false);
|
|
hda_dsp_ctrl_ppcap_int_enable(sdev, false);
|
|
|
|
/* disable hda bus irq and streams */
|
|
hda_dsp_ctrl_stop_chip(sdev);
|
|
|
|
/* disable LP retention mode */
|
|
snd_sof_pci_update_bits(sdev, PCI_PGCTL,
|
|
PCI_PGCTL_LSRMD_MASK, PCI_PGCTL_LSRMD_MASK);
|
|
|
|
/* reset controller */
|
|
ret = hda_dsp_ctrl_link_reset(sdev, true);
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev,
|
|
"error: failed to reset controller during suspend\n");
|
|
return ret;
|
|
}
|
|
|
|
/* display codec can powered off after link reset */
|
|
hda_codec_i915_display_power(sdev, false);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int hda_resume(struct snd_sof_dev *sdev, bool runtime_resume)
|
|
{
|
|
#if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
|
|
struct hdac_bus *bus = sof_to_bus(sdev);
|
|
struct hdac_ext_link *hlink = NULL;
|
|
#endif
|
|
int ret;
|
|
|
|
/* display codec must be powered before link reset */
|
|
hda_codec_i915_display_power(sdev, true);
|
|
|
|
/*
|
|
* clear TCSEL to clear playback on some HD Audio
|
|
* codecs. PCI TCSEL is defined in the Intel manuals.
|
|
*/
|
|
snd_sof_pci_update_bits(sdev, PCI_TCSEL, 0x07, 0);
|
|
|
|
/* reset and start hda controller */
|
|
ret = hda_dsp_ctrl_init_chip(sdev, true);
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev,
|
|
"error: failed to start controller after resume\n");
|
|
goto cleanup;
|
|
}
|
|
|
|
#if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
|
|
/* check jack status */
|
|
if (runtime_resume) {
|
|
hda_codec_jack_wake_enable(sdev, false);
|
|
if (sdev->system_suspend_target == SOF_SUSPEND_NONE)
|
|
hda_codec_jack_check(sdev);
|
|
}
|
|
|
|
/* turn off the links that were off before suspend */
|
|
list_for_each_entry(hlink, &bus->hlink_list, list) {
|
|
if (!hlink->ref_count)
|
|
snd_hdac_ext_bus_link_power_down(hlink);
|
|
}
|
|
|
|
/* check dma status and clean up CORB/RIRB buffers */
|
|
if (!bus->cmd_dma_state)
|
|
snd_hdac_bus_stop_cmd_io(bus);
|
|
#endif
|
|
|
|
/* enable ppcap interrupt */
|
|
hda_dsp_ctrl_ppcap_enable(sdev, true);
|
|
hda_dsp_ctrl_ppcap_int_enable(sdev, true);
|
|
|
|
cleanup:
|
|
/* display codec can powered off after controller init */
|
|
hda_codec_i915_display_power(sdev, false);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int hda_dsp_resume(struct snd_sof_dev *sdev)
|
|
{
|
|
struct sof_intel_hda_dev *hda = sdev->pdata->hw_pdata;
|
|
struct pci_dev *pci = to_pci_dev(sdev->dev);
|
|
const struct sof_dsp_power_state target_state = {
|
|
.state = SOF_DSP_PM_D0,
|
|
.substate = SOF_HDA_DSP_PM_D0I0,
|
|
};
|
|
#if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
|
|
struct hdac_bus *bus = sof_to_bus(sdev);
|
|
struct hdac_ext_link *hlink = NULL;
|
|
#endif
|
|
int ret;
|
|
|
|
/* resume from D0I3 */
|
|
if (sdev->dsp_power_state.state == SOF_DSP_PM_D0) {
|
|
#if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
|
|
/* power up links that were active before suspend */
|
|
list_for_each_entry(hlink, &bus->hlink_list, list) {
|
|
if (hlink->ref_count) {
|
|
ret = snd_hdac_ext_bus_link_power_up(hlink);
|
|
if (ret < 0) {
|
|
dev_dbg(sdev->dev,
|
|
"error %d in %s: failed to power up links",
|
|
ret, __func__);
|
|
return ret;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* set up CORB/RIRB buffers if was on before suspend */
|
|
if (bus->cmd_dma_state)
|
|
snd_hdac_bus_init_cmd_io(bus);
|
|
#endif
|
|
|
|
/* Set DSP power state */
|
|
ret = snd_sof_dsp_set_power_state(sdev, &target_state);
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev, "error: setting dsp state %d substate %d\n",
|
|
target_state.state, target_state.substate);
|
|
return ret;
|
|
}
|
|
|
|
/* restore L1SEN bit */
|
|
if (hda->l1_support_changed)
|
|
snd_sof_dsp_update_bits(sdev, HDA_DSP_HDA_BAR,
|
|
HDA_VS_INTEL_EM2,
|
|
HDA_VS_INTEL_EM2_L1SEN, 0);
|
|
|
|
/* restore and disable the system wakeup */
|
|
pci_restore_state(pci);
|
|
disable_irq_wake(pci->irq);
|
|
return 0;
|
|
}
|
|
|
|
/* init hda controller. DSP cores will be powered up during fw boot */
|
|
ret = hda_resume(sdev, false);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return snd_sof_dsp_set_power_state(sdev, &target_state);
|
|
}
|
|
|
|
int hda_dsp_runtime_resume(struct snd_sof_dev *sdev)
|
|
{
|
|
const struct sof_dsp_power_state target_state = {
|
|
.state = SOF_DSP_PM_D0,
|
|
};
|
|
int ret;
|
|
|
|
/* init hda controller. DSP cores will be powered up during fw boot */
|
|
ret = hda_resume(sdev, true);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return snd_sof_dsp_set_power_state(sdev, &target_state);
|
|
}
|
|
|
|
int hda_dsp_runtime_idle(struct snd_sof_dev *sdev)
|
|
{
|
|
struct hdac_bus *hbus = sof_to_bus(sdev);
|
|
|
|
if (hbus->codec_powered) {
|
|
dev_dbg(sdev->dev, "some codecs still powered (%08X), not idle\n",
|
|
(unsigned int)hbus->codec_powered);
|
|
return -EBUSY;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
int hda_dsp_runtime_suspend(struct snd_sof_dev *sdev)
|
|
{
|
|
struct sof_intel_hda_dev *hda = sdev->pdata->hw_pdata;
|
|
const struct sof_dsp_power_state target_state = {
|
|
.state = SOF_DSP_PM_D3,
|
|
};
|
|
int ret;
|
|
|
|
/* cancel any attempt for DSP D0I3 */
|
|
cancel_delayed_work_sync(&hda->d0i3_work);
|
|
|
|
/* stop hda controller and power dsp off */
|
|
ret = hda_suspend(sdev, true);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return snd_sof_dsp_set_power_state(sdev, &target_state);
|
|
}
|
|
|
|
int hda_dsp_suspend(struct snd_sof_dev *sdev, u32 target_state)
|
|
{
|
|
struct sof_intel_hda_dev *hda = sdev->pdata->hw_pdata;
|
|
struct hdac_bus *bus = sof_to_bus(sdev);
|
|
struct pci_dev *pci = to_pci_dev(sdev->dev);
|
|
const struct sof_dsp_power_state target_dsp_state = {
|
|
.state = target_state,
|
|
.substate = target_state == SOF_DSP_PM_D0 ?
|
|
SOF_HDA_DSP_PM_D0I3 : 0,
|
|
};
|
|
int ret;
|
|
|
|
/* cancel any attempt for DSP D0I3 */
|
|
cancel_delayed_work_sync(&hda->d0i3_work);
|
|
|
|
if (target_state == SOF_DSP_PM_D0) {
|
|
/* Set DSP power state */
|
|
ret = snd_sof_dsp_set_power_state(sdev, &target_dsp_state);
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev, "error: setting dsp state %d substate %d\n",
|
|
target_dsp_state.state,
|
|
target_dsp_state.substate);
|
|
return ret;
|
|
}
|
|
|
|
/* enable L1SEN to make sure the system can enter S0Ix */
|
|
hda->l1_support_changed =
|
|
snd_sof_dsp_update_bits(sdev, HDA_DSP_HDA_BAR,
|
|
HDA_VS_INTEL_EM2,
|
|
HDA_VS_INTEL_EM2_L1SEN,
|
|
HDA_VS_INTEL_EM2_L1SEN);
|
|
|
|
#if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
|
|
/* stop the CORB/RIRB DMA if it is On */
|
|
if (bus->cmd_dma_state)
|
|
snd_hdac_bus_stop_cmd_io(bus);
|
|
|
|
/* no link can be powered in s0ix state */
|
|
ret = snd_hdac_ext_bus_link_power_down_all(bus);
|
|
if (ret < 0) {
|
|
dev_dbg(sdev->dev,
|
|
"error %d in %s: failed to power down links",
|
|
ret, __func__);
|
|
return ret;
|
|
}
|
|
#endif
|
|
|
|
/* enable the system waking up via IPC IRQ */
|
|
enable_irq_wake(pci->irq);
|
|
pci_save_state(pci);
|
|
return 0;
|
|
}
|
|
|
|
/* stop hda controller and power dsp off */
|
|
ret = hda_suspend(sdev, false);
|
|
if (ret < 0) {
|
|
dev_err(bus->dev, "error: suspending dsp\n");
|
|
return ret;
|
|
}
|
|
|
|
return snd_sof_dsp_set_power_state(sdev, &target_dsp_state);
|
|
}
|
|
|
|
int hda_dsp_shutdown(struct snd_sof_dev *sdev)
|
|
{
|
|
sdev->system_suspend_target = SOF_SUSPEND_S3;
|
|
return snd_sof_suspend(sdev->dev);
|
|
}
|
|
|
|
int hda_dsp_set_hw_params_upon_resume(struct snd_sof_dev *sdev)
|
|
{
|
|
#if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
|
|
struct hdac_bus *bus = sof_to_bus(sdev);
|
|
struct snd_soc_pcm_runtime *rtd;
|
|
struct hdac_ext_stream *hext_stream;
|
|
struct hdac_ext_link *link;
|
|
struct hdac_stream *s;
|
|
const char *name;
|
|
int stream_tag;
|
|
|
|
/* set internal flag for BE */
|
|
list_for_each_entry(s, &bus->stream_list, list) {
|
|
hext_stream = stream_to_hdac_ext_stream(s);
|
|
|
|
/*
|
|
* clear stream. This should already be taken care for running
|
|
* streams when the SUSPEND trigger is called. But paused
|
|
* streams do not get suspended, so this needs to be done
|
|
* explicitly during suspend.
|
|
*/
|
|
if (hext_stream->link_substream) {
|
|
rtd = asoc_substream_to_rtd(hext_stream->link_substream);
|
|
name = asoc_rtd_to_codec(rtd, 0)->component->name;
|
|
link = snd_hdac_ext_bus_get_link(bus, name);
|
|
if (!link)
|
|
return -EINVAL;
|
|
|
|
hext_stream->link_prepared = 0;
|
|
|
|
if (hdac_stream(hext_stream)->direction ==
|
|
SNDRV_PCM_STREAM_CAPTURE)
|
|
continue;
|
|
|
|
stream_tag = hdac_stream(hext_stream)->stream_tag;
|
|
snd_hdac_ext_link_clear_stream_id(link, stream_tag);
|
|
}
|
|
}
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
void hda_dsp_d0i3_work(struct work_struct *work)
|
|
{
|
|
struct sof_intel_hda_dev *hdev = container_of(work,
|
|
struct sof_intel_hda_dev,
|
|
d0i3_work.work);
|
|
struct hdac_bus *bus = &hdev->hbus.core;
|
|
struct snd_sof_dev *sdev = dev_get_drvdata(bus->dev);
|
|
struct sof_dsp_power_state target_state = {
|
|
.state = SOF_DSP_PM_D0,
|
|
.substate = SOF_HDA_DSP_PM_D0I3,
|
|
};
|
|
int ret;
|
|
|
|
/* DSP can enter D0I3 iff only D0I3-compatible streams are active */
|
|
if (!snd_sof_dsp_only_d0i3_compatible_stream_active(sdev))
|
|
/* remain in D0I0 */
|
|
return;
|
|
|
|
/* This can fail but error cannot be propagated */
|
|
ret = snd_sof_dsp_set_power_state(sdev, &target_state);
|
|
if (ret < 0)
|
|
dev_err_ratelimited(sdev->dev,
|
|
"error: failed to set DSP state %d substate %d\n",
|
|
target_state.state, target_state.substate);
|
|
}
|
|
|
|
int hda_dsp_core_get(struct snd_sof_dev *sdev, int core)
|
|
{
|
|
struct sof_ipc_pm_core_config pm_core_config = {
|
|
.hdr = {
|
|
.cmd = SOF_IPC_GLB_PM_MSG | SOF_IPC_PM_CORE_ENABLE,
|
|
.size = sizeof(pm_core_config),
|
|
},
|
|
.enable_mask = sdev->enabled_cores_mask | BIT(core),
|
|
};
|
|
int ret, ret1;
|
|
|
|
/* power up core */
|
|
ret = hda_dsp_enable_core(sdev, BIT(core));
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev, "failed to power up core %d with err: %d\n",
|
|
core, ret);
|
|
return ret;
|
|
}
|
|
|
|
/* No need to send IPC for primary core or if FW boot is not complete */
|
|
if (sdev->fw_state != SOF_FW_BOOT_COMPLETE || core == SOF_DSP_PRIMARY_CORE)
|
|
return 0;
|
|
|
|
/* Now notify DSP for secondary cores */
|
|
ret = sof_ipc_tx_message(sdev->ipc, pm_core_config.hdr.cmd,
|
|
&pm_core_config, sizeof(pm_core_config),
|
|
&pm_core_config, sizeof(pm_core_config));
|
|
if (ret < 0) {
|
|
dev_err(sdev->dev, "failed to enable secondary core '%d' failed with %d\n",
|
|
core, ret);
|
|
goto power_down;
|
|
}
|
|
|
|
return ret;
|
|
|
|
power_down:
|
|
/* power down core if it is host managed and return the original error if this fails too */
|
|
ret1 = hda_dsp_core_reset_power_down(sdev, BIT(core));
|
|
if (ret1 < 0)
|
|
dev_err(sdev->dev, "failed to power down core: %d with err: %d\n", core, ret1);
|
|
|
|
return ret;
|
|
}
|