533 lines
15 KiB
C
533 lines
15 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/* Copyright(c) 2013 - 2019 Intel Corporation. */
|
|
|
|
#include "fm10k_vf.h"
|
|
|
|
/**
|
|
* fm10k_stop_hw_vf - Stop Tx/Rx units
|
|
* @hw: pointer to hardware structure
|
|
*
|
|
**/
|
|
static s32 fm10k_stop_hw_vf(struct fm10k_hw *hw)
|
|
{
|
|
u8 *perm_addr = hw->mac.perm_addr;
|
|
u32 bal = 0, bah = 0, tdlen;
|
|
s32 err;
|
|
u16 i;
|
|
|
|
/* we need to disable the queues before taking further steps */
|
|
err = fm10k_stop_hw_generic(hw);
|
|
if (err && err != FM10K_ERR_REQUESTS_PENDING)
|
|
return err;
|
|
|
|
/* If permanent address is set then we need to restore it */
|
|
if (is_valid_ether_addr(perm_addr)) {
|
|
bal = (((u32)perm_addr[3]) << 24) |
|
|
(((u32)perm_addr[4]) << 16) |
|
|
(((u32)perm_addr[5]) << 8);
|
|
bah = (((u32)0xFF) << 24) |
|
|
(((u32)perm_addr[0]) << 16) |
|
|
(((u32)perm_addr[1]) << 8) |
|
|
((u32)perm_addr[2]);
|
|
}
|
|
|
|
/* restore default itr_scale for next VF initialization */
|
|
tdlen = hw->mac.itr_scale << FM10K_TDLEN_ITR_SCALE_SHIFT;
|
|
|
|
/* The queues have already been disabled so we just need to
|
|
* update their base address registers
|
|
*/
|
|
for (i = 0; i < hw->mac.max_queues; i++) {
|
|
fm10k_write_reg(hw, FM10K_TDBAL(i), bal);
|
|
fm10k_write_reg(hw, FM10K_TDBAH(i), bah);
|
|
fm10k_write_reg(hw, FM10K_RDBAL(i), bal);
|
|
fm10k_write_reg(hw, FM10K_RDBAH(i), bah);
|
|
/* Restore ITR scale in software-defined mechanism in TDLEN
|
|
* for next VF initialization. See definition of
|
|
* FM10K_TDLEN_ITR_SCALE_SHIFT for more details on the use of
|
|
* TDLEN here.
|
|
*/
|
|
fm10k_write_reg(hw, FM10K_TDLEN(i), tdlen);
|
|
}
|
|
|
|
return err;
|
|
}
|
|
|
|
/**
|
|
* fm10k_reset_hw_vf - VF hardware reset
|
|
* @hw: pointer to hardware structure
|
|
*
|
|
* This function should return the hardware to a state similar to the
|
|
* one it is in after just being initialized.
|
|
**/
|
|
static s32 fm10k_reset_hw_vf(struct fm10k_hw *hw)
|
|
{
|
|
s32 err;
|
|
|
|
/* shut down queues we own and reset DMA configuration */
|
|
err = fm10k_stop_hw_vf(hw);
|
|
if (err == FM10K_ERR_REQUESTS_PENDING)
|
|
hw->mac.reset_while_pending++;
|
|
else if (err)
|
|
return err;
|
|
|
|
/* Inititate VF reset */
|
|
fm10k_write_reg(hw, FM10K_VFCTRL, FM10K_VFCTRL_RST);
|
|
|
|
/* Flush write and allow 100us for reset to complete */
|
|
fm10k_write_flush(hw);
|
|
udelay(FM10K_RESET_TIMEOUT);
|
|
|
|
/* Clear reset bit and verify it was cleared */
|
|
fm10k_write_reg(hw, FM10K_VFCTRL, 0);
|
|
if (fm10k_read_reg(hw, FM10K_VFCTRL) & FM10K_VFCTRL_RST)
|
|
return FM10K_ERR_RESET_FAILED;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* fm10k_init_hw_vf - VF hardware initialization
|
|
* @hw: pointer to hardware structure
|
|
*
|
|
**/
|
|
static s32 fm10k_init_hw_vf(struct fm10k_hw *hw)
|
|
{
|
|
u32 tqdloc, tqdloc0 = ~fm10k_read_reg(hw, FM10K_TQDLOC(0));
|
|
s32 err;
|
|
u16 i;
|
|
|
|
/* verify we have at least 1 queue */
|
|
if (!~fm10k_read_reg(hw, FM10K_TXQCTL(0)) ||
|
|
!~fm10k_read_reg(hw, FM10K_RXQCTL(0))) {
|
|
err = FM10K_ERR_NO_RESOURCES;
|
|
goto reset_max_queues;
|
|
}
|
|
|
|
/* determine how many queues we have */
|
|
for (i = 1; tqdloc0 && (i < FM10K_MAX_QUEUES_POOL); i++) {
|
|
/* verify the Descriptor cache offsets are increasing */
|
|
tqdloc = ~fm10k_read_reg(hw, FM10K_TQDLOC(i));
|
|
if (!tqdloc || (tqdloc == tqdloc0))
|
|
break;
|
|
|
|
/* check to verify the PF doesn't own any of our queues */
|
|
if (!~fm10k_read_reg(hw, FM10K_TXQCTL(i)) ||
|
|
!~fm10k_read_reg(hw, FM10K_RXQCTL(i)))
|
|
break;
|
|
}
|
|
|
|
/* shut down queues we own and reset DMA configuration */
|
|
err = fm10k_disable_queues_generic(hw, i);
|
|
if (err)
|
|
goto reset_max_queues;
|
|
|
|
/* record maximum queue count */
|
|
hw->mac.max_queues = i;
|
|
|
|
/* fetch default VLAN and ITR scale */
|
|
hw->mac.default_vid = (fm10k_read_reg(hw, FM10K_TXQCTL(0)) &
|
|
FM10K_TXQCTL_VID_MASK) >> FM10K_TXQCTL_VID_SHIFT;
|
|
/* Read the ITR scale from TDLEN. See the definition of
|
|
* FM10K_TDLEN_ITR_SCALE_SHIFT for more information about how TDLEN is
|
|
* used here.
|
|
*/
|
|
hw->mac.itr_scale = (fm10k_read_reg(hw, FM10K_TDLEN(0)) &
|
|
FM10K_TDLEN_ITR_SCALE_MASK) >>
|
|
FM10K_TDLEN_ITR_SCALE_SHIFT;
|
|
|
|
return 0;
|
|
|
|
reset_max_queues:
|
|
hw->mac.max_queues = 0;
|
|
|
|
return err;
|
|
}
|
|
|
|
/* This structure defines the attibutes to be parsed below */
|
|
const struct fm10k_tlv_attr fm10k_mac_vlan_msg_attr[] = {
|
|
FM10K_TLV_ATTR_U32(FM10K_MAC_VLAN_MSG_VLAN),
|
|
FM10K_TLV_ATTR_BOOL(FM10K_MAC_VLAN_MSG_SET),
|
|
FM10K_TLV_ATTR_MAC_ADDR(FM10K_MAC_VLAN_MSG_MAC),
|
|
FM10K_TLV_ATTR_MAC_ADDR(FM10K_MAC_VLAN_MSG_DEFAULT_MAC),
|
|
FM10K_TLV_ATTR_MAC_ADDR(FM10K_MAC_VLAN_MSG_MULTICAST),
|
|
FM10K_TLV_ATTR_LAST
|
|
};
|
|
|
|
/**
|
|
* fm10k_update_vlan_vf - Update status of VLAN ID in VLAN filter table
|
|
* @hw: pointer to hardware structure
|
|
* @vid: VLAN ID to add to table
|
|
* @vsi: Reserved, should always be 0
|
|
* @set: Indicates if this is a set or clear operation
|
|
*
|
|
* This function adds or removes the corresponding VLAN ID from the VLAN
|
|
* filter table for this VF.
|
|
**/
|
|
static s32 fm10k_update_vlan_vf(struct fm10k_hw *hw, u32 vid, u8 vsi, bool set)
|
|
{
|
|
struct fm10k_mbx_info *mbx = &hw->mbx;
|
|
u32 msg[4];
|
|
|
|
/* verify the index is not set */
|
|
if (vsi)
|
|
return FM10K_ERR_PARAM;
|
|
|
|
/* clever trick to verify reserved bits in both vid and length */
|
|
if ((vid << 16 | vid) >> 28)
|
|
return FM10K_ERR_PARAM;
|
|
|
|
/* encode set bit into the VLAN ID */
|
|
if (!set)
|
|
vid |= FM10K_VLAN_CLEAR;
|
|
|
|
/* generate VLAN request */
|
|
fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_MAC_VLAN);
|
|
fm10k_tlv_attr_put_u32(msg, FM10K_MAC_VLAN_MSG_VLAN, vid);
|
|
|
|
/* load onto outgoing mailbox */
|
|
return mbx->ops.enqueue_tx(hw, mbx, msg);
|
|
}
|
|
|
|
/**
|
|
* fm10k_msg_mac_vlan_vf - Read device MAC address from mailbox message
|
|
* @hw: pointer to the HW structure
|
|
* @results: Attributes for message
|
|
* @mbx: unused mailbox data
|
|
*
|
|
* This function should determine the MAC address for the VF
|
|
**/
|
|
s32 fm10k_msg_mac_vlan_vf(struct fm10k_hw *hw, u32 **results,
|
|
struct fm10k_mbx_info __always_unused *mbx)
|
|
{
|
|
u8 perm_addr[ETH_ALEN];
|
|
u16 vid;
|
|
s32 err;
|
|
|
|
/* record MAC address requested */
|
|
err = fm10k_tlv_attr_get_mac_vlan(
|
|
results[FM10K_MAC_VLAN_MSG_DEFAULT_MAC],
|
|
perm_addr, &vid);
|
|
if (err)
|
|
return err;
|
|
|
|
ether_addr_copy(hw->mac.perm_addr, perm_addr);
|
|
hw->mac.default_vid = vid & (FM10K_VLAN_TABLE_VID_MAX - 1);
|
|
hw->mac.vlan_override = !!(vid & FM10K_VLAN_OVERRIDE);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* fm10k_read_mac_addr_vf - Read device MAC address
|
|
* @hw: pointer to the HW structure
|
|
*
|
|
* This function should determine the MAC address for the VF
|
|
**/
|
|
static s32 fm10k_read_mac_addr_vf(struct fm10k_hw *hw)
|
|
{
|
|
u8 perm_addr[ETH_ALEN];
|
|
u32 base_addr;
|
|
|
|
base_addr = fm10k_read_reg(hw, FM10K_TDBAL(0));
|
|
|
|
/* last byte should be 0 */
|
|
if (base_addr << 24)
|
|
return FM10K_ERR_INVALID_MAC_ADDR;
|
|
|
|
perm_addr[3] = (u8)(base_addr >> 24);
|
|
perm_addr[4] = (u8)(base_addr >> 16);
|
|
perm_addr[5] = (u8)(base_addr >> 8);
|
|
|
|
base_addr = fm10k_read_reg(hw, FM10K_TDBAH(0));
|
|
|
|
/* first byte should be all 1's */
|
|
if ((~base_addr) >> 24)
|
|
return FM10K_ERR_INVALID_MAC_ADDR;
|
|
|
|
perm_addr[0] = (u8)(base_addr >> 16);
|
|
perm_addr[1] = (u8)(base_addr >> 8);
|
|
perm_addr[2] = (u8)(base_addr);
|
|
|
|
ether_addr_copy(hw->mac.perm_addr, perm_addr);
|
|
ether_addr_copy(hw->mac.addr, perm_addr);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* fm10k_update_uc_addr_vf - Update device unicast addresses
|
|
* @hw: pointer to the HW structure
|
|
* @glort: unused
|
|
* @mac: MAC address to add/remove from table
|
|
* @vid: VLAN ID to add/remove from table
|
|
* @add: Indicates if this is an add or remove operation
|
|
* @flags: flags field to indicate add and secure - unused
|
|
*
|
|
* This function is used to add or remove unicast MAC addresses for
|
|
* the VF.
|
|
**/
|
|
static s32 fm10k_update_uc_addr_vf(struct fm10k_hw *hw,
|
|
u16 __always_unused glort,
|
|
const u8 *mac, u16 vid, bool add,
|
|
u8 __always_unused flags)
|
|
{
|
|
struct fm10k_mbx_info *mbx = &hw->mbx;
|
|
u32 msg[7];
|
|
|
|
/* verify VLAN ID is valid */
|
|
if (vid >= FM10K_VLAN_TABLE_VID_MAX)
|
|
return FM10K_ERR_PARAM;
|
|
|
|
/* verify MAC address is valid */
|
|
if (!is_valid_ether_addr(mac))
|
|
return FM10K_ERR_PARAM;
|
|
|
|
/* verify we are not locked down on the MAC address */
|
|
if (is_valid_ether_addr(hw->mac.perm_addr) &&
|
|
!ether_addr_equal(hw->mac.perm_addr, mac))
|
|
return FM10K_ERR_PARAM;
|
|
|
|
/* add bit to notify us if this is a set or clear operation */
|
|
if (!add)
|
|
vid |= FM10K_VLAN_CLEAR;
|
|
|
|
/* generate VLAN request */
|
|
fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_MAC_VLAN);
|
|
fm10k_tlv_attr_put_mac_vlan(msg, FM10K_MAC_VLAN_MSG_MAC, mac, vid);
|
|
|
|
/* load onto outgoing mailbox */
|
|
return mbx->ops.enqueue_tx(hw, mbx, msg);
|
|
}
|
|
|
|
/**
|
|
* fm10k_update_mc_addr_vf - Update device multicast addresses
|
|
* @hw: pointer to the HW structure
|
|
* @glort: unused
|
|
* @mac: MAC address to add/remove from table
|
|
* @vid: VLAN ID to add/remove from table
|
|
* @add: Indicates if this is an add or remove operation
|
|
*
|
|
* This function is used to add or remove multicast MAC addresses for
|
|
* the VF.
|
|
**/
|
|
static s32 fm10k_update_mc_addr_vf(struct fm10k_hw *hw,
|
|
u16 __always_unused glort,
|
|
const u8 *mac, u16 vid, bool add)
|
|
{
|
|
struct fm10k_mbx_info *mbx = &hw->mbx;
|
|
u32 msg[7];
|
|
|
|
/* verify VLAN ID is valid */
|
|
if (vid >= FM10K_VLAN_TABLE_VID_MAX)
|
|
return FM10K_ERR_PARAM;
|
|
|
|
/* verify multicast address is valid */
|
|
if (!is_multicast_ether_addr(mac))
|
|
return FM10K_ERR_PARAM;
|
|
|
|
/* add bit to notify us if this is a set or clear operation */
|
|
if (!add)
|
|
vid |= FM10K_VLAN_CLEAR;
|
|
|
|
/* generate VLAN request */
|
|
fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_MAC_VLAN);
|
|
fm10k_tlv_attr_put_mac_vlan(msg, FM10K_MAC_VLAN_MSG_MULTICAST,
|
|
mac, vid);
|
|
|
|
/* load onto outgoing mailbox */
|
|
return mbx->ops.enqueue_tx(hw, mbx, msg);
|
|
}
|
|
|
|
/**
|
|
* fm10k_update_int_moderator_vf - Request update of interrupt moderator list
|
|
* @hw: pointer to hardware structure
|
|
*
|
|
* This function will issue a request to the PF to rescan our MSI-X table
|
|
* and to update the interrupt moderator linked list.
|
|
**/
|
|
static void fm10k_update_int_moderator_vf(struct fm10k_hw *hw)
|
|
{
|
|
struct fm10k_mbx_info *mbx = &hw->mbx;
|
|
u32 msg[1];
|
|
|
|
/* generate MSI-X request */
|
|
fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_MSIX);
|
|
|
|
/* load onto outgoing mailbox */
|
|
mbx->ops.enqueue_tx(hw, mbx, msg);
|
|
}
|
|
|
|
/* This structure defines the attibutes to be parsed below */
|
|
const struct fm10k_tlv_attr fm10k_lport_state_msg_attr[] = {
|
|
FM10K_TLV_ATTR_BOOL(FM10K_LPORT_STATE_MSG_DISABLE),
|
|
FM10K_TLV_ATTR_U8(FM10K_LPORT_STATE_MSG_XCAST_MODE),
|
|
FM10K_TLV_ATTR_BOOL(FM10K_LPORT_STATE_MSG_READY),
|
|
FM10K_TLV_ATTR_LAST
|
|
};
|
|
|
|
/**
|
|
* fm10k_msg_lport_state_vf - Message handler for lport_state message from PF
|
|
* @hw: Pointer to hardware structure
|
|
* @results: pointer array containing parsed data
|
|
* @mbx: Pointer to mailbox information structure
|
|
*
|
|
* This handler is meant to capture the indication from the PF that we
|
|
* are ready to bring up the interface.
|
|
**/
|
|
s32 fm10k_msg_lport_state_vf(struct fm10k_hw *hw, u32 **results,
|
|
struct fm10k_mbx_info __always_unused *mbx)
|
|
{
|
|
hw->mac.dglort_map = !results[FM10K_LPORT_STATE_MSG_READY] ?
|
|
FM10K_DGLORTMAP_NONE : FM10K_DGLORTMAP_ZERO;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* fm10k_update_lport_state_vf - Update device state in lower device
|
|
* @hw: pointer to the HW structure
|
|
* @glort: unused
|
|
* @count: number of logical ports to enable - unused (always 1)
|
|
* @enable: boolean value indicating if this is an enable or disable request
|
|
*
|
|
* Notify the lower device of a state change. If the lower device is
|
|
* enabled we can add filters, if it is disabled all filters for this
|
|
* logical port are flushed.
|
|
**/
|
|
static s32 fm10k_update_lport_state_vf(struct fm10k_hw *hw,
|
|
u16 __always_unused glort,
|
|
u16 __always_unused count, bool enable)
|
|
{
|
|
struct fm10k_mbx_info *mbx = &hw->mbx;
|
|
u32 msg[2];
|
|
|
|
/* reset glort mask 0 as we have to wait to be enabled */
|
|
hw->mac.dglort_map = FM10K_DGLORTMAP_NONE;
|
|
|
|
/* generate port state request */
|
|
fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_LPORT_STATE);
|
|
if (!enable)
|
|
fm10k_tlv_attr_put_bool(msg, FM10K_LPORT_STATE_MSG_DISABLE);
|
|
|
|
/* load onto outgoing mailbox */
|
|
return mbx->ops.enqueue_tx(hw, mbx, msg);
|
|
}
|
|
|
|
/**
|
|
* fm10k_update_xcast_mode_vf - Request update of multicast mode
|
|
* @hw: pointer to hardware structure
|
|
* @glort: unused
|
|
* @mode: integer value indicating mode being requested
|
|
*
|
|
* This function will attempt to request a higher mode for the port
|
|
* so that it can enable either multicast, multicast promiscuous, or
|
|
* promiscuous mode of operation.
|
|
**/
|
|
static s32 fm10k_update_xcast_mode_vf(struct fm10k_hw *hw,
|
|
u16 __always_unused glort, u8 mode)
|
|
{
|
|
struct fm10k_mbx_info *mbx = &hw->mbx;
|
|
u32 msg[3];
|
|
|
|
if (mode > FM10K_XCAST_MODE_NONE)
|
|
return FM10K_ERR_PARAM;
|
|
|
|
/* generate message requesting to change xcast mode */
|
|
fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_LPORT_STATE);
|
|
fm10k_tlv_attr_put_u8(msg, FM10K_LPORT_STATE_MSG_XCAST_MODE, mode);
|
|
|
|
/* load onto outgoing mailbox */
|
|
return mbx->ops.enqueue_tx(hw, mbx, msg);
|
|
}
|
|
|
|
/**
|
|
* fm10k_update_hw_stats_vf - Updates hardware related statistics of VF
|
|
* @hw: pointer to hardware structure
|
|
* @stats: pointer to statistics structure
|
|
*
|
|
* This function collects and aggregates per queue hardware statistics.
|
|
**/
|
|
static void fm10k_update_hw_stats_vf(struct fm10k_hw *hw,
|
|
struct fm10k_hw_stats *stats)
|
|
{
|
|
fm10k_update_hw_stats_q(hw, stats->q, 0, hw->mac.max_queues);
|
|
}
|
|
|
|
/**
|
|
* fm10k_rebind_hw_stats_vf - Resets base for hardware statistics of VF
|
|
* @hw: pointer to hardware structure
|
|
* @stats: pointer to the stats structure to update
|
|
*
|
|
* This function resets the base for queue hardware statistics.
|
|
**/
|
|
static void fm10k_rebind_hw_stats_vf(struct fm10k_hw *hw,
|
|
struct fm10k_hw_stats *stats)
|
|
{
|
|
/* Unbind Queue Statistics */
|
|
fm10k_unbind_hw_stats_q(stats->q, 0, hw->mac.max_queues);
|
|
|
|
/* Reinitialize bases for all stats */
|
|
fm10k_update_hw_stats_vf(hw, stats);
|
|
}
|
|
|
|
/**
|
|
* fm10k_configure_dglort_map_vf - Configures GLORT entry and queues
|
|
* @hw: pointer to hardware structure
|
|
* @dglort: pointer to dglort configuration structure
|
|
*
|
|
* Reads the configuration structure contained in dglort_cfg and uses
|
|
* that information to then populate a DGLORTMAP/DEC entry and the queues
|
|
* to which it has been assigned.
|
|
**/
|
|
static s32 fm10k_configure_dglort_map_vf(struct fm10k_hw __always_unused *hw,
|
|
struct fm10k_dglort_cfg *dglort)
|
|
{
|
|
/* verify the dglort pointer */
|
|
if (!dglort)
|
|
return FM10K_ERR_PARAM;
|
|
|
|
/* stub for now until we determine correct message for this */
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct fm10k_msg_data fm10k_msg_data_vf[] = {
|
|
FM10K_TLV_MSG_TEST_HANDLER(fm10k_tlv_msg_test),
|
|
FM10K_VF_MSG_MAC_VLAN_HANDLER(fm10k_msg_mac_vlan_vf),
|
|
FM10K_VF_MSG_LPORT_STATE_HANDLER(fm10k_msg_lport_state_vf),
|
|
FM10K_TLV_MSG_ERROR_HANDLER(fm10k_tlv_msg_error),
|
|
};
|
|
|
|
static const struct fm10k_mac_ops mac_ops_vf = {
|
|
.get_bus_info = fm10k_get_bus_info_generic,
|
|
.reset_hw = fm10k_reset_hw_vf,
|
|
.init_hw = fm10k_init_hw_vf,
|
|
.start_hw = fm10k_start_hw_generic,
|
|
.stop_hw = fm10k_stop_hw_vf,
|
|
.update_vlan = fm10k_update_vlan_vf,
|
|
.read_mac_addr = fm10k_read_mac_addr_vf,
|
|
.update_uc_addr = fm10k_update_uc_addr_vf,
|
|
.update_mc_addr = fm10k_update_mc_addr_vf,
|
|
.update_xcast_mode = fm10k_update_xcast_mode_vf,
|
|
.update_int_moderator = fm10k_update_int_moderator_vf,
|
|
.update_lport_state = fm10k_update_lport_state_vf,
|
|
.update_hw_stats = fm10k_update_hw_stats_vf,
|
|
.rebind_hw_stats = fm10k_rebind_hw_stats_vf,
|
|
.configure_dglort_map = fm10k_configure_dglort_map_vf,
|
|
.get_host_state = fm10k_get_host_state_generic,
|
|
};
|
|
|
|
static s32 fm10k_get_invariants_vf(struct fm10k_hw *hw)
|
|
{
|
|
fm10k_get_invariants_generic(hw);
|
|
|
|
return fm10k_pfvf_mbx_init(hw, &hw->mbx, fm10k_msg_data_vf, 0);
|
|
}
|
|
|
|
const struct fm10k_info fm10k_vf_info = {
|
|
.mac = fm10k_mac_vf,
|
|
.get_invariants = fm10k_get_invariants_vf,
|
|
.mac_ops = &mac_ops_vf,
|
|
};
|