437 lines
10 KiB
Plaintext
437 lines
10 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* MPC8323E EMDS Device Tree Source
|
|
*
|
|
* Copyright 2006 Freescale Semiconductor Inc.
|
|
*
|
|
|
|
* To enable external serial I/O on a Freescale MPC 8323 SYS/MDS board, do
|
|
* this:
|
|
*
|
|
* 1) On chip U61, lift (disconnect) pins 21 (TXD) and 22 (RXD) from the board.
|
|
* 2) Solder a wire from U61-21 to P19A-23. P19 is a grid of pins on the board
|
|
* next to the serial ports.
|
|
* 3) Solder a wire from U61-22 to P19K-22.
|
|
*
|
|
* Note that there's a typo in the schematic. The board labels the last column
|
|
* of pins "P19K", but in the schematic, that column is called "P19J". So if
|
|
* you're going by the schematic, the pin is called "P19J-K22".
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
/ {
|
|
model = "MPC8323EMDS";
|
|
compatible = "MPC8323EMDS", "MPC832xMDS", "MPC83xxMDS";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
aliases {
|
|
ethernet0 = &enet0;
|
|
ethernet1 = &enet1;
|
|
serial0 = &serial0;
|
|
serial1 = &serial1;
|
|
pci0 = &pci0;
|
|
};
|
|
|
|
cpus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
PowerPC,8323@0 {
|
|
device_type = "cpu";
|
|
reg = <0x0>;
|
|
d-cache-line-size = <32>; // 32 bytes
|
|
i-cache-line-size = <32>; // 32 bytes
|
|
d-cache-size = <16384>; // L1, 16K
|
|
i-cache-size = <16384>; // L1, 16K
|
|
timebase-frequency = <0>;
|
|
bus-frequency = <0>;
|
|
clock-frequency = <0>;
|
|
};
|
|
};
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x08000000>;
|
|
};
|
|
|
|
bcsr@f8000000 {
|
|
compatible = "fsl,mpc8323mds-bcsr";
|
|
reg = <0xf8000000 0x8000>;
|
|
};
|
|
|
|
soc8323@e0000000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
device_type = "soc";
|
|
compatible = "simple-bus";
|
|
ranges = <0x0 0xe0000000 0x00100000>;
|
|
reg = <0xe0000000 0x00000200>;
|
|
bus-frequency = <132000000>;
|
|
|
|
wdt@200 {
|
|
device_type = "watchdog";
|
|
compatible = "mpc83xx_wdt";
|
|
reg = <0x200 0x100>;
|
|
};
|
|
|
|
pmc: power@b00 {
|
|
compatible = "fsl,mpc8323-pmc", "fsl,mpc8349-pmc";
|
|
reg = <0xb00 0x100 0xa00 0x100>;
|
|
interrupts = <80 0x8>;
|
|
interrupt-parent = <&ipic>;
|
|
};
|
|
|
|
i2c@3000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
cell-index = <0>;
|
|
compatible = "fsl-i2c";
|
|
reg = <0x3000 0x100>;
|
|
interrupts = <14 0x8>;
|
|
interrupt-parent = <&ipic>;
|
|
dfsrr;
|
|
|
|
rtc@68 {
|
|
compatible = "dallas,ds1374";
|
|
reg = <0x68>;
|
|
};
|
|
};
|
|
|
|
serial0: serial@4500 {
|
|
cell-index = <0>;
|
|
device_type = "serial";
|
|
compatible = "fsl,ns16550", "ns16550";
|
|
reg = <0x4500 0x100>;
|
|
clock-frequency = <0>;
|
|
interrupts = <9 0x8>;
|
|
interrupt-parent = <&ipic>;
|
|
};
|
|
|
|
serial1: serial@4600 {
|
|
cell-index = <1>;
|
|
device_type = "serial";
|
|
compatible = "fsl,ns16550", "ns16550";
|
|
reg = <0x4600 0x100>;
|
|
clock-frequency = <0>;
|
|
interrupts = <10 0x8>;
|
|
interrupt-parent = <&ipic>;
|
|
};
|
|
|
|
dma@82a8 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "fsl,mpc8323-dma", "fsl,elo-dma";
|
|
reg = <0x82a8 4>;
|
|
ranges = <0 0x8100 0x1a8>;
|
|
interrupt-parent = <&ipic>;
|
|
interrupts = <71 8>;
|
|
cell-index = <0>;
|
|
dma-channel@0 {
|
|
compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
|
|
reg = <0 0x80>;
|
|
cell-index = <0>;
|
|
interrupt-parent = <&ipic>;
|
|
interrupts = <71 8>;
|
|
};
|
|
dma-channel@80 {
|
|
compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
|
|
reg = <0x80 0x80>;
|
|
cell-index = <1>;
|
|
interrupt-parent = <&ipic>;
|
|
interrupts = <71 8>;
|
|
};
|
|
dma-channel@100 {
|
|
compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
|
|
reg = <0x100 0x80>;
|
|
cell-index = <2>;
|
|
interrupt-parent = <&ipic>;
|
|
interrupts = <71 8>;
|
|
};
|
|
dma-channel@180 {
|
|
compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
|
|
reg = <0x180 0x28>;
|
|
cell-index = <3>;
|
|
interrupt-parent = <&ipic>;
|
|
interrupts = <71 8>;
|
|
};
|
|
};
|
|
|
|
crypto@30000 {
|
|
compatible = "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
|
|
reg = <0x30000 0x10000>;
|
|
interrupts = <11 0x8>;
|
|
interrupt-parent = <&ipic>;
|
|
fsl,num-channels = <1>;
|
|
fsl,channel-fifo-len = <24>;
|
|
fsl,exec-units-mask = <0x4c>;
|
|
fsl,descriptor-types-mask = <0x0122003f>;
|
|
sleep = <&pmc 0x03000000>;
|
|
};
|
|
|
|
ipic: pic@700 {
|
|
interrupt-controller;
|
|
#address-cells = <0>;
|
|
#interrupt-cells = <2>;
|
|
reg = <0x700 0x100>;
|
|
device_type = "ipic";
|
|
};
|
|
|
|
par_io@1400 {
|
|
reg = <0x1400 0x100>;
|
|
device_type = "par_io";
|
|
num-ports = <7>;
|
|
|
|
pio3: ucc_pin@3 {
|
|
pio-map = <
|
|
/* port pin dir open_drain assignment has_irq */
|
|
3 4 3 0 2 0 /* MDIO */
|
|
3 5 1 0 2 0 /* MDC */
|
|
0 13 2 0 1 0 /* RX_CLK (CLK9) */
|
|
3 24 2 0 1 0 /* TX_CLK (CLK10) */
|
|
1 0 1 0 1 0 /* TxD0 */
|
|
1 1 1 0 1 0 /* TxD1 */
|
|
1 2 1 0 1 0 /* TxD2 */
|
|
1 3 1 0 1 0 /* TxD3 */
|
|
1 4 2 0 1 0 /* RxD0 */
|
|
1 5 2 0 1 0 /* RxD1 */
|
|
1 6 2 0 1 0 /* RxD2 */
|
|
1 7 2 0 1 0 /* RxD3 */
|
|
1 8 2 0 1 0 /* RX_ER */
|
|
1 9 1 0 1 0 /* TX_ER */
|
|
1 10 2 0 1 0 /* RX_DV */
|
|
1 11 2 0 1 0 /* COL */
|
|
1 12 1 0 1 0 /* TX_EN */
|
|
1 13 2 0 1 0>; /* CRS */
|
|
};
|
|
pio4: ucc_pin@4 {
|
|
pio-map = <
|
|
/* port pin dir open_drain assignment has_irq */
|
|
3 31 2 0 1 0 /* RX_CLK (CLK7) */
|
|
3 6 2 0 1 0 /* TX_CLK (CLK8) */
|
|
1 18 1 0 1 0 /* TxD0 */
|
|
1 19 1 0 1 0 /* TxD1 */
|
|
1 20 1 0 1 0 /* TxD2 */
|
|
1 21 1 0 1 0 /* TxD3 */
|
|
1 22 2 0 1 0 /* RxD0 */
|
|
1 23 2 0 1 0 /* RxD1 */
|
|
1 24 2 0 1 0 /* RxD2 */
|
|
1 25 2 0 1 0 /* RxD3 */
|
|
1 26 2 0 1 0 /* RX_ER */
|
|
1 27 1 0 1 0 /* TX_ER */
|
|
1 28 2 0 1 0 /* RX_DV */
|
|
1 29 2 0 1 0 /* COL */
|
|
1 30 1 0 1 0 /* TX_EN */
|
|
1 31 2 0 1 0>; /* CRS */
|
|
};
|
|
pio5: ucc_pin@5 {
|
|
pio-map = <
|
|
/*
|
|
* open has
|
|
* port pin dir drain sel irq
|
|
*/
|
|
2 0 1 0 2 0 /* TxD5 */
|
|
2 8 2 0 2 0 /* RxD5 */
|
|
|
|
2 29 2 0 0 0 /* CTS5 */
|
|
2 31 1 0 2 0 /* RTS5 */
|
|
|
|
2 24 2 0 0 0 /* CD */
|
|
|
|
>;
|
|
};
|
|
|
|
};
|
|
};
|
|
|
|
qe@e0100000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
device_type = "qe";
|
|
compatible = "fsl,qe";
|
|
ranges = <0x0 0xe0100000 0x00100000>;
|
|
reg = <0xe0100000 0x480>;
|
|
brg-frequency = <0>;
|
|
bus-frequency = <198000000>;
|
|
fsl,qe-num-riscs = <1>;
|
|
fsl,qe-num-snums = <28>;
|
|
|
|
muram@10000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "fsl,qe-muram", "fsl,cpm-muram";
|
|
ranges = <0x0 0x00010000 0x00004000>;
|
|
|
|
data-only@0 {
|
|
compatible = "fsl,qe-muram-data",
|
|
"fsl,cpm-muram-data";
|
|
reg = <0x0 0x4000>;
|
|
};
|
|
};
|
|
|
|
spi@4c0 {
|
|
cell-index = <0>;
|
|
compatible = "fsl,spi";
|
|
reg = <0x4c0 0x40>;
|
|
interrupts = <2>;
|
|
interrupt-parent = <&qeic>;
|
|
mode = "cpu";
|
|
};
|
|
|
|
spi@500 {
|
|
cell-index = <1>;
|
|
compatible = "fsl,spi";
|
|
reg = <0x500 0x40>;
|
|
interrupts = <1>;
|
|
interrupt-parent = <&qeic>;
|
|
mode = "cpu";
|
|
};
|
|
|
|
usb@6c0 {
|
|
compatible = "qe_udc";
|
|
reg = <0x6c0 0x40 0x8b00 0x100>;
|
|
interrupts = <11>;
|
|
interrupt-parent = <&qeic>;
|
|
mode = "slave";
|
|
};
|
|
|
|
enet0: ucc@2200 {
|
|
device_type = "network";
|
|
compatible = "ucc_geth";
|
|
cell-index = <3>;
|
|
reg = <0x2200 0x200>;
|
|
interrupts = <34>;
|
|
interrupt-parent = <&qeic>;
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
rx-clock-name = "clk9";
|
|
tx-clock-name = "clk10";
|
|
phy-handle = <&phy3>;
|
|
pio-handle = <&pio3>;
|
|
};
|
|
|
|
enet1: ucc@3200 {
|
|
device_type = "network";
|
|
compatible = "ucc_geth";
|
|
cell-index = <4>;
|
|
reg = <0x3200 0x200>;
|
|
interrupts = <35>;
|
|
interrupt-parent = <&qeic>;
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
rx-clock-name = "clk7";
|
|
tx-clock-name = "clk8";
|
|
phy-handle = <&phy4>;
|
|
pio-handle = <&pio4>;
|
|
};
|
|
|
|
ucc@2400 {
|
|
device_type = "serial";
|
|
compatible = "ucc_uart";
|
|
cell-index = <5>; /* The UCC number, 1-7*/
|
|
port-number = <0>; /* Which ttyQEx device */
|
|
soft-uart; /* We need Soft-UART */
|
|
reg = <0x2400 0x200>;
|
|
interrupts = <40>; /* From Table 18-12 */
|
|
interrupt-parent = < &qeic >;
|
|
/*
|
|
* For Soft-UART, we need to set TX to 1X, which
|
|
* means specifying separate clock sources.
|
|
*/
|
|
rx-clock-name = "brg5";
|
|
tx-clock-name = "brg6";
|
|
pio-handle = < &pio5 >;
|
|
};
|
|
|
|
|
|
mdio@2320 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x2320 0x18>;
|
|
compatible = "fsl,ucc-mdio";
|
|
|
|
phy3: ethernet-phy@3 {
|
|
interrupt-parent = <&ipic>;
|
|
interrupts = <17 0x8>;
|
|
reg = <0x3>;
|
|
};
|
|
phy4: ethernet-phy@4 {
|
|
interrupt-parent = <&ipic>;
|
|
interrupts = <18 0x8>;
|
|
reg = <0x4>;
|
|
};
|
|
};
|
|
|
|
qeic: interrupt-controller@80 {
|
|
interrupt-controller;
|
|
compatible = "fsl,qe-ic";
|
|
#address-cells = <0>;
|
|
#interrupt-cells = <1>;
|
|
reg = <0x80 0x80>;
|
|
big-endian;
|
|
interrupts = <32 0x8 33 0x8>; //high:32 low:33
|
|
interrupt-parent = <&ipic>;
|
|
};
|
|
};
|
|
|
|
pci0: pci@e0008500 {
|
|
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
|
|
interrupt-map = <
|
|
/* IDSEL 0x11 AD17 */
|
|
0x8800 0x0 0x0 0x1 &ipic 20 0x8
|
|
0x8800 0x0 0x0 0x2 &ipic 21 0x8
|
|
0x8800 0x0 0x0 0x3 &ipic 22 0x8
|
|
0x8800 0x0 0x0 0x4 &ipic 23 0x8
|
|
|
|
/* IDSEL 0x12 AD18 */
|
|
0x9000 0x0 0x0 0x1 &ipic 22 0x8
|
|
0x9000 0x0 0x0 0x2 &ipic 23 0x8
|
|
0x9000 0x0 0x0 0x3 &ipic 20 0x8
|
|
0x9000 0x0 0x0 0x4 &ipic 21 0x8
|
|
|
|
/* IDSEL 0x13 AD19 */
|
|
0x9800 0x0 0x0 0x1 &ipic 23 0x8
|
|
0x9800 0x0 0x0 0x2 &ipic 20 0x8
|
|
0x9800 0x0 0x0 0x3 &ipic 21 0x8
|
|
0x9800 0x0 0x0 0x4 &ipic 22 0x8
|
|
|
|
/* IDSEL 0x15 AD21*/
|
|
0xa800 0x0 0x0 0x1 &ipic 20 0x8
|
|
0xa800 0x0 0x0 0x2 &ipic 21 0x8
|
|
0xa800 0x0 0x0 0x3 &ipic 22 0x8
|
|
0xa800 0x0 0x0 0x4 &ipic 23 0x8
|
|
|
|
/* IDSEL 0x16 AD22*/
|
|
0xb000 0x0 0x0 0x1 &ipic 23 0x8
|
|
0xb000 0x0 0x0 0x2 &ipic 20 0x8
|
|
0xb000 0x0 0x0 0x3 &ipic 21 0x8
|
|
0xb000 0x0 0x0 0x4 &ipic 22 0x8
|
|
|
|
/* IDSEL 0x17 AD23*/
|
|
0xb800 0x0 0x0 0x1 &ipic 22 0x8
|
|
0xb800 0x0 0x0 0x2 &ipic 23 0x8
|
|
0xb800 0x0 0x0 0x3 &ipic 20 0x8
|
|
0xb800 0x0 0x0 0x4 &ipic 21 0x8
|
|
|
|
/* IDSEL 0x18 AD24*/
|
|
0xc000 0x0 0x0 0x1 &ipic 21 0x8
|
|
0xc000 0x0 0x0 0x2 &ipic 22 0x8
|
|
0xc000 0x0 0x0 0x3 &ipic 23 0x8
|
|
0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
|
|
interrupt-parent = <&ipic>;
|
|
interrupts = <66 0x8>;
|
|
bus-range = <0x0 0x0>;
|
|
ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
|
|
0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
|
|
0x01000000 0x0 0x00000000 0xd0000000 0x0 0x00100000>;
|
|
clock-frequency = <0>;
|
|
#interrupt-cells = <1>;
|
|
#size-cells = <2>;
|
|
#address-cells = <3>;
|
|
reg = <0xe0008500 0x100 /* internal registers */
|
|
0xe0008300 0x8>; /* config space access registers */
|
|
compatible = "fsl,mpc8349-pci";
|
|
device_type = "pci";
|
|
sleep = <&pmc 0x00010000>;
|
|
};
|
|
};
|