linux/linux-5.18.11/arch/arm/boot/dts/spear1340.dtsi

168 lines
3.7 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later
/*
* DTS file for all SPEAr1340 SoCs
*
* Copyright 2012 Viresh Kumar <vireshk@kernel.org>
*/
/include/ "spear13xx.dtsi"
/ {
compatible = "st,spear1340";
ahb {
spics: spics@e0700000{
compatible = "st,spear-spics-gpio";
reg = <0xe0700000 0x1000>;
st-spics,peripcfg-reg = <0x42c>;
st-spics,sw-enable-bit = <21>;
st-spics,cs-value-bit = <20>;
st-spics,cs-enable-mask = <3>;
st-spics,cs-enable-shift = <18>;
gpio-controller;
#gpio-cells = <2>;
status = "disabled";
};
miphy0: miphy@eb800000 {
compatible = "st,spear1340-miphy";
reg = <0xeb800000 0x4000>;
misc = <&misc>;
#phy-cells = <1>;
status = "disabled";
};
ahci0: ahci@b1000000 {
compatible = "snps,spear-ahci";
reg = <0xb1000000 0x10000>;
interrupts = <0 72 0x4>;
phys = <&miphy0 0>;
phy-names = "sata-phy";
status = "disabled";
};
pcie0: pcie@b1000000 {
compatible = "st,spear1340-pcie", "snps,dw-pcie";
reg = <0xb1000000 0x4000>, <0x80000000 0x20000>;
reg-names = "dbi", "config";
interrupts = <0 68 0x4>;
num-lanes = <1>;
phys = <&miphy0 1>;
phy-names = "pcie-phy";
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
ranges = <0x81000000 0 0 0x80020000 0 0x00010000 /* downstream I/O */
0x82000000 0 0x80030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */
bus-range = <0x00 0xff>;
status = "disabled";
};
i2s-play@b2400000 {
compatible = "snps,designware-i2s";
reg = <0xb2400000 0x10000>;
interrupt-names = "play_irq";
interrupts = <0 98 0x4
0 99 0x4>;
play;
channel = <8>;
status = "disabled";
};
i2s-rec@b2000000 {
compatible = "snps,designware-i2s";
reg = <0xb2000000 0x10000>;
interrupt-names = "record_irq";
interrupts = <0 100 0x4
0 101 0x4>;
record;
channel = <8>;
status = "disabled";
};
pinmux: pinmux@e0700000 {
compatible = "st,spear1340-pinmux";
reg = <0xe0700000 0x1000>;
#gpio-range-cells = <3>;
};
pwm: pwm@e0180000 {
compatible ="st,spear13xx-pwm";
reg = <0xe0180000 0x1000>;
#pwm-cells = <2>;
status = "disabled";
};
spdif-in@d0100000 {
compatible = "st,spdif-in";
reg = < 0xd0100000 0x20000
0xd0110000 0x10000 >;
interrupts = <0 84 0x4>;
status = "disabled";
};
spdif-out@d0000000 {
compatible = "st,spdif-out";
reg = <0xd0000000 0x20000>;
interrupts = <0 85 0x4>;
status = "disabled";
};
spi1: spi@5d400000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x5d400000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0 99 0x4>;
status = "disabled";
};
apb {
i2c1: i2c@b4000000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,designware-i2c";
reg = <0xb4000000 0x1000>;
interrupts = <0 104 0x4>;
write-16bit;
status = "disabled";
};
serial@b4100000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0xb4100000 0x1000>;
interrupts = <0 105 0x4>;
status = "disabled";
dmas = <&dwdma0 13 0 1>,
<&dwdma0 12 1 0>;
dma-names = "rx", "tx";
};
thermal@e07008c4 {
st,thermal-flags = <0x2a00>;
};
gpiopinctrl: gpio@e2800000 {
compatible = "st,spear-plgpio";
reg = <0xe2800000 0x1000>;
interrupts = <0 107 0x4>;
#interrupt-cells = <1>;
interrupt-controller;
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&pinmux 0 0 252>;
status = "disabled";
st-plgpio,ngpio = <250>;
st-plgpio,wdata-reg = <0x40>;
st-plgpio,dir-reg = <0x00>;
st-plgpio,ie-reg = <0x80>;
st-plgpio,rdata-reg = <0x20>;
st-plgpio,mis-reg = <0xa0>;
st-plgpio,eit-reg = <0x60>;
};
};
};
};