917 lines
21 KiB
Plaintext
917 lines
21 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Samsung's S5PV210 based Galaxy Aries board device tree source
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include "s5pv210.dtsi"
|
|
|
|
/ {
|
|
compatible = "samsung,aries", "samsung,s5pv210";
|
|
|
|
aliases: aliases {
|
|
i2c4 = &i2c_sound;
|
|
i2c5 = &i2c_accel;
|
|
i2c6 = &i2c_pmic;
|
|
i2c7 = &i2c_musb;
|
|
i2c9 = &i2c_fuel;
|
|
i2c10 = &i2c_touchkey;
|
|
i2c11 = &i2c_prox;
|
|
i2c12 = &i2c_magnetometer;
|
|
};
|
|
|
|
memory@30000000 {
|
|
device_type = "memory";
|
|
reg = <0x30000000 0x05000000
|
|
0x40000000 0x10000000
|
|
0x50000000 0x08000000>;
|
|
};
|
|
|
|
reserved-memory {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
mfc_left: region@43000000 {
|
|
compatible = "shared-dma-pool";
|
|
no-map;
|
|
reg = <0x43000000 0x2000000>;
|
|
};
|
|
|
|
mfc_right: region@51000000 {
|
|
compatible = "shared-dma-pool";
|
|
no-map;
|
|
reg = <0x51000000 0x2000000>;
|
|
};
|
|
};
|
|
|
|
pmic_ap_clk: clock-0 {
|
|
/* Workaround for missing clock on PMIC */
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <32768>;
|
|
};
|
|
|
|
bt_codec: bt-sco {
|
|
compatible = "linux,bt-sco";
|
|
#sound-dai-cells = <0>;
|
|
};
|
|
|
|
vibrator_pwr: regulator-fixed-0 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vibrator-en";
|
|
enable-active-high;
|
|
gpio = <&gpj1 1 GPIO_ACTIVE_HIGH>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&vibrator_ena>;
|
|
};
|
|
|
|
touchkey_vdd: regulator-fixed-1 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VTOUCH_3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
enable-active-high;
|
|
gpio = <&gpj3 2 GPIO_ACTIVE_HIGH>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&touchkey_vdd_ena>;
|
|
};
|
|
|
|
gp2a_vled: regulator-fixed-2 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VLED";
|
|
enable-active-high;
|
|
gpio = <&gpj1 4 GPIO_ACTIVE_HIGH>;
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gp2a_power>;
|
|
};
|
|
|
|
wifi_pwrseq: wifi-pwrseq {
|
|
compatible = "mmc-pwrseq-simple";
|
|
reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&wlan_gpio_rst>;
|
|
post-power-on-delay-ms = <500>;
|
|
power-off-delay-us = <500>;
|
|
};
|
|
|
|
i2c_sound: i2c-gpio-0 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&mp05 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&mp05 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sound_i2c_pins>;
|
|
|
|
wm8994: audio-codec@1a {
|
|
compatible = "wlf,wm8994";
|
|
reg = <0x1a>;
|
|
|
|
#sound-dai-cells = <0>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
clocks = <&clocks MOUT_CLKOUT>;
|
|
clock-names = "MCLK1";
|
|
|
|
AVDD2-supply = <&buck3_reg>;
|
|
DBVDD-supply = <&buck3_reg>;
|
|
CPVDD-supply = <&buck3_reg>;
|
|
SPKVDD1-supply = <&buck3_reg>;
|
|
SPKVDD2-supply = <&buck3_reg>;
|
|
|
|
wlf,gpio-cfg = <0xa101 0x8100 0x0100 0x0100 0x8100
|
|
0xa101 0x0100 0x8100 0x0100 0x0100
|
|
0x0100>;
|
|
|
|
wlf,ldo1ena = <&gpf3 4 GPIO_ACTIVE_HIGH>;
|
|
wlf,ldo2ena = <&gpf3 4 GPIO_ACTIVE_HIGH>;
|
|
|
|
wlf,lineout1-se;
|
|
wlf,lineout2-se;
|
|
|
|
assigned-clocks = <&clocks MOUT_CLKOUT>;
|
|
assigned-clock-rates = <0>;
|
|
assigned-clock-parents = <&xusbxti>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&codec_ldo>;
|
|
};
|
|
};
|
|
|
|
i2c_accel: i2c-gpio-1 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpj3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpj3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&accel_i2c_pins>;
|
|
|
|
accelerometer@38 {
|
|
compatible = "bosch,bma023";
|
|
reg = <0x38>;
|
|
|
|
vdd-supply = <&ldo9_reg>;
|
|
vddio-supply = <&ldo9_reg>;
|
|
};
|
|
};
|
|
|
|
i2c_pmic: i2c-gpio-2 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pmic_i2c_pins>;
|
|
|
|
pmic@66 {
|
|
compatible = "maxim,max8998";
|
|
reg = <0x66>;
|
|
interrupt-parent = <&gph0>;
|
|
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
|
|
|
|
max8998,pmic-buck1-default-dvs-idx = <1>;
|
|
max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>,
|
|
<&gph0 4 GPIO_ACTIVE_HIGH>;
|
|
max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>,
|
|
<1050000>, <950000>;
|
|
|
|
max8998,pmic-buck2-default-dvs-idx = <0>;
|
|
max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
|
|
max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pmic_dvs_pins &pmic_irq>;
|
|
|
|
regulators {
|
|
ldo2_reg: LDO2 {
|
|
regulator-name = "VALIVE_1.2V";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-always-on;
|
|
|
|
regulator-state-mem {
|
|
regulator-on-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo3_reg: LDO3 {
|
|
regulator-name = "VUSB_1.1V";
|
|
regulator-min-microvolt = <1100000>;
|
|
regulator-max-microvolt = <1100000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo4_reg: LDO4 {
|
|
regulator-name = "VADC_3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo5_reg: LDO5 {
|
|
regulator-name = "VTF_2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo6_reg: LDO6 {
|
|
regulator-name = "LDO6";
|
|
regulator-min-microvolt = <1600000>;
|
|
regulator-max-microvolt = <3600000>;
|
|
};
|
|
|
|
ldo7_reg: LDO7 {
|
|
regulator-name = "VLCD_1.8V";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo8_reg: LDO8 {
|
|
regulator-name = "VUSB_3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo9_reg: LDO9 {
|
|
regulator-name = "VCC_2.8V_PDA";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo10_reg: LDO10 {
|
|
regulator-name = "VPLL_1.2V";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-always-on;
|
|
|
|
regulator-state-mem {
|
|
regulator-on-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo11_reg: LDO11 {
|
|
regulator-name = "CAM_AF_3.0V";
|
|
regulator-min-microvolt = <3000000>;
|
|
regulator-max-microvolt = <3000000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo12_reg: LDO12 {
|
|
regulator-name = "CAM_SENSOR_CORE_1.2V";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo13_reg: LDO13 {
|
|
regulator-name = "VGA_VDDIO_2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo14_reg: LDO14 {
|
|
regulator-name = "VGA_DVDD_1.8V";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo15_reg: LDO15 {
|
|
regulator-name = "CAM_ISP_HOST_2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo16_reg: LDO16 {
|
|
regulator-name = "VGA_AVDD_2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo17_reg: LDO17 {
|
|
regulator-name = "VCC_3.0V_LCD";
|
|
regulator-min-microvolt = <3000000>;
|
|
regulator-max-microvolt = <3000000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
buck1_reg: BUCK1 {
|
|
regulator-name = "vddarm";
|
|
regulator-min-microvolt = <750000>;
|
|
regulator-max-microvolt = <1500000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
regulator-suspend-microvolt = <1250000>;
|
|
};
|
|
};
|
|
|
|
buck2_reg: BUCK2 {
|
|
regulator-name = "vddint";
|
|
regulator-min-microvolt = <750000>;
|
|
regulator-max-microvolt = <1500000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
regulator-suspend-microvolt = <1100000>;
|
|
};
|
|
};
|
|
|
|
buck3_reg: BUCK3 {
|
|
regulator-name = "VCC_1.8V";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
buck4_reg: BUCK4 {
|
|
regulator-name = "CAM_ISP_CORE_1.2V";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ap32khz_reg: EN32KHz-AP {
|
|
regulator-name = "32KHz AP";
|
|
regulator-always-on;
|
|
};
|
|
|
|
cp32khz_reg: EN32KHz-CP {
|
|
regulator-name = "32KHz CP";
|
|
};
|
|
|
|
vichg_reg: ENVICHG {
|
|
regulator-name = "VICHG";
|
|
regulator-always-on;
|
|
};
|
|
|
|
safe1_sreg: ESAFEOUT1 {
|
|
regulator-name = "SAFEOUT1";
|
|
};
|
|
|
|
safe2_sreg: ESAFEOUT2 {
|
|
regulator-name = "SAFEOUT2";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
i2c_musb: i2c-gpio-3 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpj3 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpj3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&musb_i2c_pins>;
|
|
|
|
fsa9480: musb@25 {
|
|
compatible = "fcs,fsa9480";
|
|
reg = <0x25>;
|
|
interrupt-parent = <&gph2>;
|
|
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&musb_irq>;
|
|
};
|
|
};
|
|
|
|
i2c_fuel: i2c-gpio-4 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&fg_i2c_pins>;
|
|
|
|
fg: fuelgauge@36 {
|
|
compatible = "maxim,max17040";
|
|
reg = <0x36>;
|
|
};
|
|
};
|
|
|
|
i2c_touchkey: i2c-gpio-5 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpj3 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpj3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&touchkey_i2c_pins>;
|
|
|
|
touchkey@20 {
|
|
compatible = "cypress,aries-touchkey";
|
|
reg = <0x20>;
|
|
vdd-supply = <&touchkey_vdd>;
|
|
vcc-supply = <&buck3_reg>;
|
|
linux,keycodes = <KEY_MENU KEY_BACK
|
|
KEY_HOMEPAGE KEY_SEARCH>;
|
|
interrupt-parent = <&gpj4>;
|
|
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&touchkey_irq>;
|
|
};
|
|
};
|
|
|
|
i2c_prox: i2c-gpio-6 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpg2 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpg0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&prox_i2c_pins>;
|
|
|
|
light-sensor@44 {
|
|
compatible = "sharp,gp2ap002a00f";
|
|
reg = <0x44>;
|
|
interrupt-parent = <&gph0>;
|
|
interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
|
|
vdd-supply = <&gp2a_vled>;
|
|
vio-supply = <&gp2a_vled>;
|
|
io-channels = <&gp2a_shunt>;
|
|
io-channel-names = "alsout";
|
|
sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
|
|
sharp,proximity-close-hysteresis = /bits/ 8 <0x20>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gp2a_irq>;
|
|
};
|
|
};
|
|
|
|
i2c_magnetometer: i2c-gpio-7 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpj0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpj0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&magnetometer_i2c_pins>;
|
|
|
|
status = "disabled";
|
|
|
|
/* Yamaha yas529 magnetometer, no mainline binding */
|
|
};
|
|
|
|
vibrator: pwm-vibrator {
|
|
compatible = "pwm-vibrator";
|
|
pwms = <&pwm 1 44642 0>;
|
|
pwm-names = "enable";
|
|
vcc-supply = <&vibrator_pwr>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pwm1_out>;
|
|
};
|
|
|
|
poweroff: syscon-poweroff {
|
|
compatible = "syscon-poweroff";
|
|
regmap = <&pmu_syscon>;
|
|
offset = <0x681c>; /* PS_HOLD_CONTROL */
|
|
value = <0x5200>;
|
|
};
|
|
|
|
spi_lcd: spi-2 {
|
|
compatible = "spi-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
sck-gpios = <&mp04 1 GPIO_ACTIVE_HIGH>;
|
|
mosi-gpios = <&mp04 3 GPIO_ACTIVE_HIGH>;
|
|
cs-gpios = <&mp01 1 GPIO_ACTIVE_HIGH>;
|
|
num-chipselects = <1>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&lcd_spi_pins>;
|
|
|
|
panel@0 {
|
|
compatible = "samsung,s6e63m0";
|
|
reg = <0>;
|
|
reset-gpios = <&mp05 5 GPIO_ACTIVE_LOW>;
|
|
vdd3-supply = <&ldo7_reg>;
|
|
vci-supply = <&ldo17_reg>;
|
|
spi-max-frequency = <1200000>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&panel_rst>;
|
|
|
|
port {
|
|
lcd_ep: endpoint {
|
|
remote-endpoint = <&fimd_ep>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&adc {
|
|
vdd-supply = <&ldo4_reg>;
|
|
|
|
status = "okay";
|
|
|
|
gp2a_shunt: current-sense-shunt {
|
|
compatible = "current-sense-shunt";
|
|
io-channels = <&adc 9>;
|
|
shunt-resistor-micro-ohms = <47000000>; /* 47 ohms */
|
|
#io-channel-cells = <0>;
|
|
};
|
|
};
|
|
|
|
&fimd {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&lcd_clk &lcd_data24>;
|
|
status = "okay";
|
|
|
|
samsung,invert-vden;
|
|
samsung,invert-vclk;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
fimd_ep: endpoint {
|
|
remote-endpoint = <&lcd_ep>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&hsotg {
|
|
vusb_a-supply = <&ldo8_reg>;
|
|
vusb_d-supply = <&ldo3_reg>;
|
|
dr_mode = "peripheral";
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c2 {
|
|
samsung,i2c-sda-delay = <100>;
|
|
samsung,i2c-max-bus-freq = <400000>;
|
|
samsung,i2c-slave-addr = <0x10>;
|
|
status = "okay";
|
|
|
|
touchscreen@4a {
|
|
compatible = "atmel,maxtouch";
|
|
reg = <0x4a>;
|
|
interrupt-parent = <&gpj0>;
|
|
interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&ts_irq>;
|
|
reset-gpios = <&gpj1 3 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
&i2s0 {
|
|
dmas = <&pdma0 10>, <&pdma0 9>, <&pdma0 11>;
|
|
status = "okay";
|
|
};
|
|
|
|
&mfc {
|
|
memory-region = <&mfc_left>, <&mfc_right>;
|
|
};
|
|
|
|
&pinctrl0 {
|
|
bt_reset: bt-reset-pins {
|
|
samsung,pins = "gpb-3";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
wlan_bt_en: wlan-bt-en-pins {
|
|
samsung,pins = "gpb-5";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-val = <1>;
|
|
};
|
|
|
|
codec_ldo: codec-ldo-pins {
|
|
samsung,pins = "gpf3-4";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
};
|
|
|
|
prox_i2c_pins: gp2a-i2c-pins {
|
|
samsung,pins = "gpg0-2", "gpg2-2";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
wlan_gpio_rst: wlan-gpio-rst-pins {
|
|
samsung,pins = "gpg1-2";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
};
|
|
|
|
bt_wake: bt-wake-pins {
|
|
samsung,pins = "gpg3-4";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
};
|
|
|
|
gp2a_irq: gp2a-irq-pins {
|
|
samsung,pins = "gph0-2";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
pmic_dvs_pins: pmic-dvs-pins {
|
|
samsung,pins = "gph0-3", "gph0-4", "gph0-5";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
samsung,pin-val = <0>;
|
|
};
|
|
|
|
pmic_irq: pmic-irq-pins {
|
|
samsung,pins = "gph0-7";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
wifi_host_wake: wifi-host-wake-pins {
|
|
samsung,pins = "gph2-4";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
bt_host_wake: bt-host-wake-pins {
|
|
samsung,pins = "gph2-5";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
musb_irq: musq-irq-pins {
|
|
samsung,pins = "gph2-7";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
tf_detect: tf-detect-pins {
|
|
samsung,pins = "gph3-4";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
wifi_wake: wifi-wake-pins {
|
|
samsung,pins = "gph3-5";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
};
|
|
|
|
magnetometer_i2c_pins: yas529-i2c-pins-pins {
|
|
samsung,pins = "gpj0-0", "gpj0-1";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
ts_irq: ts-irq-pins {
|
|
samsung,pins = "gpj0-5";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
vibrator_ena: vibrator-ena-pins {
|
|
samsung,pins = "gpj1-1";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
gp2a_power: gp2a-power-pins {
|
|
samsung,pins = "gpj1-4";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
touchkey_i2c_pins: touchkey-i2c-pins {
|
|
samsung,pins = "gpj3-0", "gpj3-1";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
touchkey_vdd_ena: touchkey-vdd-ena-pins {
|
|
samsung,pins = "gpj3-2";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
musb_i2c_pins: musb-i2c-pins {
|
|
samsung,pins = "gpj3-4", "gpj3-5";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
accel_i2c_pins: accel-i2c-pins {
|
|
samsung,pins = "gpj3-6", "gpj3-7";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
pmic_i2c_pins: pmic-i2c-pins-pins {
|
|
samsung,pins = "gpj4-0", "gpj4-3";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
touchkey_irq: touchkey-irq-pins {
|
|
samsung,pins = "gpj4-1";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
lcd_spi_pins: spi-lcd-pins {
|
|
samsung,pins = "mp01-1", "mp04-1", "mp04-3";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
fg_i2c_pins: fg-i2c-pins {
|
|
samsung,pins = "mp05-0", "mp05-1";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
sound_i2c_pins: sound-i2c-pins {
|
|
samsung,pins = "mp05-2", "mp05-3";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
|
|
panel_rst: panel-rst-pins {
|
|
samsung,pins = "mp05-5";
|
|
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
};
|
|
|
|
&pwm {
|
|
samsung,pwm-outputs = <1>;
|
|
};
|
|
|
|
&rtc {
|
|
clocks = <&clocks CLK_RTC>, <&pmic_ap_clk>;
|
|
clock-names = "rtc", "rtc_src";
|
|
};
|
|
|
|
&sdhci1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
bus-width = <4>;
|
|
max-frequency = <38400000>;
|
|
pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus4 &wifi_wake &wifi_host_wake &wlan_bt_en>;
|
|
pinctrl-names = "default";
|
|
cap-sd-highspeed;
|
|
cap-mmc-highspeed;
|
|
keep-power-in-suspend;
|
|
|
|
mmc-pwrseq = <&wifi_pwrseq>;
|
|
non-removable;
|
|
status = "okay";
|
|
|
|
assigned-clocks = <&clocks MOUT_MMC1>, <&clocks SCLK_MMC1>;
|
|
assigned-clock-rates = <0>, <50000000>;
|
|
assigned-clock-parents = <&clocks MOUT_MPLL>;
|
|
|
|
wlan@1 {
|
|
reg = <1>;
|
|
compatible = "brcm,bcm4329-fmac";
|
|
interrupt-parent = <&gph2>;
|
|
interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "host-wake";
|
|
};
|
|
};
|
|
|
|
&sdhci2 {
|
|
bus-width = <4>;
|
|
cd-gpios = <&gph3 4 GPIO_ACTIVE_LOW>;
|
|
vmmc-supply = <&ldo5_reg>;
|
|
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &tf_detect>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
assigned-clocks = <&clocks MOUT_MMC2>, <&clocks SCLK_MMC2>;
|
|
assigned-clock-rates = <0>, <50000000>;
|
|
assigned-clock-parents = <&clocks MOUT_MPLL>;
|
|
};
|
|
|
|
&uart0 {
|
|
assigned-clocks = <&clocks MOUT_UART0>, <&clocks SCLK_UART0>;
|
|
assigned-clock-rates = <0>, <111166667>;
|
|
assigned-clock-parents = <&clocks MOUT_MPLL>;
|
|
|
|
status = "okay";
|
|
|
|
bluetooth {
|
|
compatible = "brcm,bcm4329-bt";
|
|
max-speed = <3000000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_data &uart0_fctl &bt_host_wake
|
|
&bt_reset &bt_wake>;
|
|
shutdown-gpios = <&gpb 3 GPIO_ACTIVE_HIGH>;
|
|
device-wakeup-gpios = <&gpg3 4 GPIO_ACTIVE_HIGH>;
|
|
interrupt-parent = <&gph2>;
|
|
interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "host-wakeup";
|
|
};
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usbphy {
|
|
status = "okay";
|
|
vbus-supply = <&safe1_sreg>;
|
|
};
|
|
|
|
&xusbxti {
|
|
clock-frequency = <24000000>;
|
|
};
|