652 lines
24 KiB
ReStructuredText
652 lines
24 KiB
ReStructuredText
==================================
|
|
DMAengine controller documentation
|
|
==================================
|
|
|
|
Hardware Introduction
|
|
=====================
|
|
|
|
Most of the Slave DMA controllers have the same general principles of
|
|
operations.
|
|
|
|
They have a given number of channels to use for the DMA transfers, and
|
|
a given number of requests lines.
|
|
|
|
Requests and channels are pretty much orthogonal. Channels can be used
|
|
to serve several to any requests. To simplify, channels are the
|
|
entities that will be doing the copy, and requests what endpoints are
|
|
involved.
|
|
|
|
The request lines actually correspond to physical lines going from the
|
|
DMA-eligible devices to the controller itself. Whenever the device
|
|
will want to start a transfer, it will assert a DMA request (DRQ) by
|
|
asserting that request line.
|
|
|
|
A very simple DMA controller would only take into account a single
|
|
parameter: the transfer size. At each clock cycle, it would transfer a
|
|
byte of data from one buffer to another, until the transfer size has
|
|
been reached.
|
|
|
|
That wouldn't work well in the real world, since slave devices might
|
|
require a specific number of bits to be transferred in a single
|
|
cycle. For example, we may want to transfer as much data as the
|
|
physical bus allows to maximize performances when doing a simple
|
|
memory copy operation, but our audio device could have a narrower FIFO
|
|
that requires data to be written exactly 16 or 24 bits at a time. This
|
|
is why most if not all of the DMA controllers can adjust this, using a
|
|
parameter called the transfer width.
|
|
|
|
Moreover, some DMA controllers, whenever the RAM is used as a source
|
|
or destination, can group the reads or writes in memory into a buffer,
|
|
so instead of having a lot of small memory accesses, which is not
|
|
really efficient, you'll get several bigger transfers. This is done
|
|
using a parameter called the burst size, that defines how many single
|
|
reads/writes it's allowed to do without the controller splitting the
|
|
transfer into smaller sub-transfers.
|
|
|
|
Our theoretical DMA controller would then only be able to do transfers
|
|
that involve a single contiguous block of data. However, some of the
|
|
transfers we usually have are not, and want to copy data from
|
|
non-contiguous buffers to a contiguous buffer, which is called
|
|
scatter-gather.
|
|
|
|
DMAEngine, at least for mem2dev transfers, require support for
|
|
scatter-gather. So we're left with two cases here: either we have a
|
|
quite simple DMA controller that doesn't support it, and we'll have to
|
|
implement it in software, or we have a more advanced DMA controller,
|
|
that implements in hardware scatter-gather.
|
|
|
|
The latter are usually programmed using a collection of chunks to
|
|
transfer, and whenever the transfer is started, the controller will go
|
|
over that collection, doing whatever we programmed there.
|
|
|
|
This collection is usually either a table or a linked list. You will
|
|
then push either the address of the table and its number of elements,
|
|
or the first item of the list to one channel of the DMA controller,
|
|
and whenever a DRQ will be asserted, it will go through the collection
|
|
to know where to fetch the data from.
|
|
|
|
Either way, the format of this collection is completely dependent on
|
|
your hardware. Each DMA controller will require a different structure,
|
|
but all of them will require, for every chunk, at least the source and
|
|
destination addresses, whether it should increment these addresses or
|
|
not and the three parameters we saw earlier: the burst size, the
|
|
transfer width and the transfer size.
|
|
|
|
The one last thing is that usually, slave devices won't issue DRQ by
|
|
default, and you have to enable this in your slave device driver first
|
|
whenever you're willing to use DMA.
|
|
|
|
These were just the general memory-to-memory (also called mem2mem) or
|
|
memory-to-device (mem2dev) kind of transfers. Most devices often
|
|
support other kind of transfers or memory operations that dmaengine
|
|
support and will be detailed later in this document.
|
|
|
|
DMA Support in Linux
|
|
====================
|
|
|
|
Historically, DMA controller drivers have been implemented using the
|
|
async TX API, to offload operations such as memory copy, XOR,
|
|
cryptography, etc., basically any memory to memory operation.
|
|
|
|
Over time, the need for memory to device transfers arose, and
|
|
dmaengine was extended. Nowadays, the async TX API is written as a
|
|
layer on top of dmaengine, and acts as a client. Still, dmaengine
|
|
accommodates that API in some cases, and made some design choices to
|
|
ensure that it stayed compatible.
|
|
|
|
For more information on the Async TX API, please look the relevant
|
|
documentation file in Documentation/crypto/async-tx-api.rst.
|
|
|
|
DMAEngine APIs
|
|
==============
|
|
|
|
``struct dma_device`` Initialization
|
|
------------------------------------
|
|
|
|
Just like any other kernel framework, the whole DMAEngine registration
|
|
relies on the driver filling a structure and registering against the
|
|
framework. In our case, that structure is dma_device.
|
|
|
|
The first thing you need to do in your driver is to allocate this
|
|
structure. Any of the usual memory allocators will do, but you'll also
|
|
need to initialize a few fields in there:
|
|
|
|
- ``channels``: should be initialized as a list using the
|
|
INIT_LIST_HEAD macro for example
|
|
|
|
- ``src_addr_widths``:
|
|
should contain a bitmask of the supported source transfer width
|
|
|
|
- ``dst_addr_widths``:
|
|
should contain a bitmask of the supported destination transfer width
|
|
|
|
- ``directions``:
|
|
should contain a bitmask of the supported slave directions
|
|
(i.e. excluding mem2mem transfers)
|
|
|
|
- ``residue_granularity``:
|
|
granularity of the transfer residue reported to dma_set_residue.
|
|
This can be either:
|
|
|
|
- Descriptor:
|
|
your device doesn't support any kind of residue
|
|
reporting. The framework will only know that a particular
|
|
transaction descriptor is done.
|
|
|
|
- Segment:
|
|
your device is able to report which chunks have been transferred
|
|
|
|
- Burst:
|
|
your device is able to report which burst have been transferred
|
|
|
|
- ``dev``: should hold the pointer to the ``struct device`` associated
|
|
to your current driver instance.
|
|
|
|
Supported transaction types
|
|
---------------------------
|
|
|
|
The next thing you need is to set which transaction types your device
|
|
(and driver) supports.
|
|
|
|
Our ``dma_device structure`` has a field called cap_mask that holds the
|
|
various types of transaction supported, and you need to modify this
|
|
mask using the dma_cap_set function, with various flags depending on
|
|
transaction types you support as an argument.
|
|
|
|
All those capabilities are defined in the ``dma_transaction_type enum``,
|
|
in ``include/linux/dmaengine.h``
|
|
|
|
Currently, the types available are:
|
|
|
|
- DMA_MEMCPY
|
|
|
|
- The device is able to do memory to memory copies
|
|
|
|
- - DMA_MEMCPY_SG
|
|
|
|
- The device supports memory to memory scatter-gather transfers.
|
|
|
|
- Even though a plain memcpy can look like a particular case of a
|
|
scatter-gather transfer, with a single chunk to copy, it's a distinct
|
|
transaction type in the mem2mem transfer case. This is because some very
|
|
simple devices might be able to do contiguous single-chunk memory copies,
|
|
but have no support for more complex SG transfers.
|
|
|
|
- No matter what the overall size of the combined chunks for source and
|
|
destination is, only as many bytes as the smallest of the two will be
|
|
transmitted. That means the number and size of the scatter-gather buffers in
|
|
both lists need not be the same, and that the operation functionally is
|
|
equivalent to a ``strncpy`` where the ``count`` argument equals the smallest
|
|
total size of the two scatter-gather list buffers.
|
|
|
|
- It's usually used for copying pixel data between host memory and
|
|
memory-mapped GPU device memory, such as found on modern PCI video graphics
|
|
cards. The most immediate example is the OpenGL API function
|
|
``glReadPielx()``, which might require a verbatim copy of a huge framebuffer
|
|
from local device memory onto host memory.
|
|
|
|
- DMA_XOR
|
|
|
|
- The device is able to perform XOR operations on memory areas
|
|
|
|
- Used to accelerate XOR intensive tasks, such as RAID5
|
|
|
|
- DMA_XOR_VAL
|
|
|
|
- The device is able to perform parity check using the XOR
|
|
algorithm against a memory buffer.
|
|
|
|
- DMA_PQ
|
|
|
|
- The device is able to perform RAID6 P+Q computations, P being a
|
|
simple XOR, and Q being a Reed-Solomon algorithm.
|
|
|
|
- DMA_PQ_VAL
|
|
|
|
- The device is able to perform parity check using RAID6 P+Q
|
|
algorithm against a memory buffer.
|
|
|
|
- DMA_INTERRUPT
|
|
|
|
- The device is able to trigger a dummy transfer that will
|
|
generate periodic interrupts
|
|
|
|
- Used by the client drivers to register a callback that will be
|
|
called on a regular basis through the DMA controller interrupt
|
|
|
|
- DMA_PRIVATE
|
|
|
|
- The devices only supports slave transfers, and as such isn't
|
|
available for async transfers.
|
|
|
|
- DMA_ASYNC_TX
|
|
|
|
- Must not be set by the device, and will be set by the framework
|
|
if needed
|
|
|
|
- TODO: What is it about?
|
|
|
|
- DMA_SLAVE
|
|
|
|
- The device can handle device to memory transfers, including
|
|
scatter-gather transfers.
|
|
|
|
- While in the mem2mem case we were having two distinct types to
|
|
deal with a single chunk to copy or a collection of them, here,
|
|
we just have a single transaction type that is supposed to
|
|
handle both.
|
|
|
|
- If you want to transfer a single contiguous memory buffer,
|
|
simply build a scatter list with only one item.
|
|
|
|
- DMA_CYCLIC
|
|
|
|
- The device can handle cyclic transfers.
|
|
|
|
- A cyclic transfer is a transfer where the chunk collection will
|
|
loop over itself, with the last item pointing to the first.
|
|
|
|
- It's usually used for audio transfers, where you want to operate
|
|
on a single ring buffer that you will fill with your audio data.
|
|
|
|
- DMA_INTERLEAVE
|
|
|
|
- The device supports interleaved transfer.
|
|
|
|
- These transfers can transfer data from a non-contiguous buffer
|
|
to a non-contiguous buffer, opposed to DMA_SLAVE that can
|
|
transfer data from a non-contiguous data set to a continuous
|
|
destination buffer.
|
|
|
|
- It's usually used for 2d content transfers, in which case you
|
|
want to transfer a portion of uncompressed data directly to the
|
|
display to print it
|
|
|
|
- DMA_COMPLETION_NO_ORDER
|
|
|
|
- The device does not support in order completion.
|
|
|
|
- The driver should return DMA_OUT_OF_ORDER for device_tx_status if
|
|
the device is setting this capability.
|
|
|
|
- All cookie tracking and checking API should be treated as invalid if
|
|
the device exports this capability.
|
|
|
|
- At this point, this is incompatible with polling option for dmatest.
|
|
|
|
- If this cap is set, the user is recommended to provide an unique
|
|
identifier for each descriptor sent to the DMA device in order to
|
|
properly track the completion.
|
|
|
|
- DMA_REPEAT
|
|
|
|
- The device supports repeated transfers. A repeated transfer, indicated by
|
|
the DMA_PREP_REPEAT transfer flag, is similar to a cyclic transfer in that
|
|
it gets automatically repeated when it ends, but can additionally be
|
|
replaced by the client.
|
|
|
|
- This feature is limited to interleaved transfers, this flag should thus not
|
|
be set if the DMA_INTERLEAVE flag isn't set. This limitation is based on
|
|
the current needs of DMA clients, support for additional transfer types
|
|
should be added in the future if and when the need arises.
|
|
|
|
- DMA_LOAD_EOT
|
|
|
|
- The device supports replacing repeated transfers at end of transfer (EOT)
|
|
by queuing a new transfer with the DMA_PREP_LOAD_EOT flag set.
|
|
|
|
- Support for replacing a currently running transfer at another point (such
|
|
as end of burst instead of end of transfer) will be added in the future
|
|
based on DMA clients needs, if and when the need arises.
|
|
|
|
These various types will also affect how the source and destination
|
|
addresses change over time.
|
|
|
|
Addresses pointing to RAM are typically incremented (or decremented)
|
|
after each transfer. In case of a ring buffer, they may loop
|
|
(DMA_CYCLIC). Addresses pointing to a device's register (e.g. a FIFO)
|
|
are typically fixed.
|
|
|
|
Per descriptor metadata support
|
|
-------------------------------
|
|
Some data movement architecture (DMA controller and peripherals) uses metadata
|
|
associated with a transaction. The DMA controller role is to transfer the
|
|
payload and the metadata alongside.
|
|
The metadata itself is not used by the DMA engine itself, but it contains
|
|
parameters, keys, vectors, etc for peripheral or from the peripheral.
|
|
|
|
The DMAengine framework provides a generic ways to facilitate the metadata for
|
|
descriptors. Depending on the architecture the DMA driver can implement either
|
|
or both of the methods and it is up to the client driver to choose which one
|
|
to use.
|
|
|
|
- DESC_METADATA_CLIENT
|
|
|
|
The metadata buffer is allocated/provided by the client driver and it is
|
|
attached (via the dmaengine_desc_attach_metadata() helper to the descriptor.
|
|
|
|
From the DMA driver the following is expected for this mode:
|
|
|
|
- DMA_MEM_TO_DEV / DEV_MEM_TO_MEM
|
|
|
|
The data from the provided metadata buffer should be prepared for the DMA
|
|
controller to be sent alongside of the payload data. Either by copying to a
|
|
hardware descriptor, or highly coupled packet.
|
|
|
|
- DMA_DEV_TO_MEM
|
|
|
|
On transfer completion the DMA driver must copy the metadata to the client
|
|
provided metadata buffer before notifying the client about the completion.
|
|
After the transfer completion, DMA drivers must not touch the metadata
|
|
buffer provided by the client.
|
|
|
|
- DESC_METADATA_ENGINE
|
|
|
|
The metadata buffer is allocated/managed by the DMA driver. The client driver
|
|
can ask for the pointer, maximum size and the currently used size of the
|
|
metadata and can directly update or read it. dmaengine_desc_get_metadata_ptr()
|
|
and dmaengine_desc_set_metadata_len() is provided as helper functions.
|
|
|
|
From the DMA driver the following is expected for this mode:
|
|
|
|
- get_metadata_ptr()
|
|
|
|
Should return a pointer for the metadata buffer, the maximum size of the
|
|
metadata buffer and the currently used / valid (if any) bytes in the buffer.
|
|
|
|
- set_metadata_len()
|
|
|
|
It is called by the clients after it have placed the metadata to the buffer
|
|
to let the DMA driver know the number of valid bytes provided.
|
|
|
|
Note: since the client will ask for the metadata pointer in the completion
|
|
callback (in DMA_DEV_TO_MEM case) the DMA driver must ensure that the
|
|
descriptor is not freed up prior the callback is called.
|
|
|
|
Device operations
|
|
-----------------
|
|
|
|
Our dma_device structure also requires a few function pointers in
|
|
order to implement the actual logic, now that we described what
|
|
operations we were able to perform.
|
|
|
|
The functions that we have to fill in there, and hence have to
|
|
implement, obviously depend on the transaction types you reported as
|
|
supported.
|
|
|
|
- ``device_alloc_chan_resources``
|
|
|
|
- ``device_free_chan_resources``
|
|
|
|
- These functions will be called whenever a driver will call
|
|
``dma_request_channel`` or ``dma_release_channel`` for the first/last
|
|
time on the channel associated to that driver.
|
|
|
|
- They are in charge of allocating/freeing all the needed
|
|
resources in order for that channel to be useful for your driver.
|
|
|
|
- These functions can sleep.
|
|
|
|
- ``device_prep_dma_*``
|
|
|
|
- These functions are matching the capabilities you registered
|
|
previously.
|
|
|
|
- These functions all take the buffer or the scatterlist relevant
|
|
for the transfer being prepared, and should create a hardware
|
|
descriptor or a list of hardware descriptors from it
|
|
|
|
- These functions can be called from an interrupt context
|
|
|
|
- Any allocation you might do should be using the GFP_NOWAIT
|
|
flag, in order not to potentially sleep, but without depleting
|
|
the emergency pool either.
|
|
|
|
- Drivers should try to pre-allocate any memory they might need
|
|
during the transfer setup at probe time to avoid putting to
|
|
much pressure on the nowait allocator.
|
|
|
|
- It should return a unique instance of the
|
|
``dma_async_tx_descriptor structure``, that further represents this
|
|
particular transfer.
|
|
|
|
- This structure can be initialized using the function
|
|
``dma_async_tx_descriptor_init``.
|
|
|
|
- You'll also need to set two fields in this structure:
|
|
|
|
- flags:
|
|
TODO: Can it be modified by the driver itself, or
|
|
should it be always the flags passed in the arguments
|
|
|
|
- tx_submit: A pointer to a function you have to implement,
|
|
that is supposed to push the current transaction descriptor to a
|
|
pending queue, waiting for issue_pending to be called.
|
|
|
|
- In this structure the function pointer callback_result can be
|
|
initialized in order for the submitter to be notified that a
|
|
transaction has completed. In the earlier code the function pointer
|
|
callback has been used. However it does not provide any status to the
|
|
transaction and will be deprecated. The result structure defined as
|
|
``dmaengine_result`` that is passed in to callback_result
|
|
has two fields:
|
|
|
|
- result: This provides the transfer result defined by
|
|
``dmaengine_tx_result``. Either success or some error condition.
|
|
|
|
- residue: Provides the residue bytes of the transfer for those that
|
|
support residue.
|
|
|
|
- ``device_issue_pending``
|
|
|
|
- Takes the first transaction descriptor in the pending queue,
|
|
and starts the transfer. Whenever that transfer is done, it
|
|
should move to the next transaction in the list.
|
|
|
|
- This function can be called in an interrupt context
|
|
|
|
- ``device_tx_status``
|
|
|
|
- Should report the bytes left to go over on the given channel
|
|
|
|
- Should only care about the transaction descriptor passed as
|
|
argument, not the currently active one on a given channel
|
|
|
|
- The tx_state argument might be NULL
|
|
|
|
- Should use dma_set_residue to report it
|
|
|
|
- In the case of a cyclic transfer, it should only take into
|
|
account the current period.
|
|
|
|
- Should return DMA_OUT_OF_ORDER if the device does not support in order
|
|
completion and is completing the operation out of order.
|
|
|
|
- This function can be called in an interrupt context.
|
|
|
|
- device_config
|
|
|
|
- Reconfigures the channel with the configuration given as argument
|
|
|
|
- This command should NOT perform synchronously, or on any
|
|
currently queued transfers, but only on subsequent ones
|
|
|
|
- In this case, the function will receive a ``dma_slave_config``
|
|
structure pointer as an argument, that will detail which
|
|
configuration to use.
|
|
|
|
- Even though that structure contains a direction field, this
|
|
field is deprecated in favor of the direction argument given to
|
|
the prep_* functions
|
|
|
|
- This call is mandatory for slave operations only. This should NOT be
|
|
set or expected to be set for memcpy operations.
|
|
If a driver support both, it should use this call for slave
|
|
operations only and not for memcpy ones.
|
|
|
|
- device_pause
|
|
|
|
- Pauses a transfer on the channel
|
|
|
|
- This command should operate synchronously on the channel,
|
|
pausing right away the work of the given channel
|
|
|
|
- device_resume
|
|
|
|
- Resumes a transfer on the channel
|
|
|
|
- This command should operate synchronously on the channel,
|
|
resuming right away the work of the given channel
|
|
|
|
- device_terminate_all
|
|
|
|
- Aborts all the pending and ongoing transfers on the channel
|
|
|
|
- For aborted transfers the complete callback should not be called
|
|
|
|
- Can be called from atomic context or from within a complete
|
|
callback of a descriptor. Must not sleep. Drivers must be able
|
|
to handle this correctly.
|
|
|
|
- Termination may be asynchronous. The driver does not have to
|
|
wait until the currently active transfer has completely stopped.
|
|
See device_synchronize.
|
|
|
|
- device_synchronize
|
|
|
|
- Must synchronize the termination of a channel to the current
|
|
context.
|
|
|
|
- Must make sure that memory for previously submitted
|
|
descriptors is no longer accessed by the DMA controller.
|
|
|
|
- Must make sure that all complete callbacks for previously
|
|
submitted descriptors have finished running and none are
|
|
scheduled to run.
|
|
|
|
- May sleep.
|
|
|
|
|
|
Misc notes
|
|
==========
|
|
|
|
(stuff that should be documented, but don't really know
|
|
where to put them)
|
|
|
|
``dma_run_dependencies``
|
|
|
|
- Should be called at the end of an async TX transfer, and can be
|
|
ignored in the slave transfers case.
|
|
|
|
- Makes sure that dependent operations are run before marking it
|
|
as complete.
|
|
|
|
dma_cookie_t
|
|
|
|
- it's a DMA transaction ID that will increment over time.
|
|
|
|
- Not really relevant any more since the introduction of ``virt-dma``
|
|
that abstracts it away.
|
|
|
|
DMA_CTRL_ACK
|
|
|
|
- If clear, the descriptor cannot be reused by provider until the
|
|
client acknowledges receipt, i.e. has a chance to establish any
|
|
dependency chains
|
|
|
|
- This can be acked by invoking async_tx_ack()
|
|
|
|
- If set, does not mean descriptor can be reused
|
|
|
|
DMA_CTRL_REUSE
|
|
|
|
- If set, the descriptor can be reused after being completed. It should
|
|
not be freed by provider if this flag is set.
|
|
|
|
- The descriptor should be prepared for reuse by invoking
|
|
``dmaengine_desc_set_reuse()`` which will set DMA_CTRL_REUSE.
|
|
|
|
- ``dmaengine_desc_set_reuse()`` will succeed only when channel support
|
|
reusable descriptor as exhibited by capabilities
|
|
|
|
- As a consequence, if a device driver wants to skip the
|
|
``dma_map_sg()`` and ``dma_unmap_sg()`` in between 2 transfers,
|
|
because the DMA'd data wasn't used, it can resubmit the transfer right after
|
|
its completion.
|
|
|
|
- Descriptor can be freed in few ways
|
|
|
|
- Clearing DMA_CTRL_REUSE by invoking
|
|
``dmaengine_desc_clear_reuse()`` and submitting for last txn
|
|
|
|
- Explicitly invoking ``dmaengine_desc_free()``, this can succeed only
|
|
when DMA_CTRL_REUSE is already set
|
|
|
|
- Terminating the channel
|
|
|
|
- DMA_PREP_CMD
|
|
|
|
- If set, the client driver tells DMA controller that passed data in DMA
|
|
API is command data.
|
|
|
|
- Interpretation of command data is DMA controller specific. It can be
|
|
used for issuing commands to other peripherals/register reads/register
|
|
writes for which the descriptor should be in different format from
|
|
normal data descriptors.
|
|
|
|
- DMA_PREP_REPEAT
|
|
|
|
- If set, the transfer will be automatically repeated when it ends until a
|
|
new transfer is queued on the same channel with the DMA_PREP_LOAD_EOT flag.
|
|
If the next transfer to be queued on the channel does not have the
|
|
DMA_PREP_LOAD_EOT flag set, the current transfer will be repeated until the
|
|
client terminates all transfers.
|
|
|
|
- This flag is only supported if the channel reports the DMA_REPEAT
|
|
capability.
|
|
|
|
- DMA_PREP_LOAD_EOT
|
|
|
|
- If set, the transfer will replace the transfer currently being executed at
|
|
the end of the transfer.
|
|
|
|
- This is the default behaviour for non-repeated transfers, specifying
|
|
DMA_PREP_LOAD_EOT for non-repeated transfers will thus make no difference.
|
|
|
|
- When using repeated transfers, DMA clients will usually need to set the
|
|
DMA_PREP_LOAD_EOT flag on all transfers, otherwise the channel will keep
|
|
repeating the last repeated transfer and ignore the new transfers being
|
|
queued. Failure to set DMA_PREP_LOAD_EOT will appear as if the channel was
|
|
stuck on the previous transfer.
|
|
|
|
- This flag is only supported if the channel reports the DMA_LOAD_EOT
|
|
capability.
|
|
|
|
General Design Notes
|
|
====================
|
|
|
|
Most of the DMAEngine drivers you'll see are based on a similar design
|
|
that handles the end of transfer interrupts in the handler, but defer
|
|
most work to a tasklet, including the start of a new transfer whenever
|
|
the previous transfer ended.
|
|
|
|
This is a rather inefficient design though, because the inter-transfer
|
|
latency will be not only the interrupt latency, but also the
|
|
scheduling latency of the tasklet, which will leave the channel idle
|
|
in between, which will slow down the global transfer rate.
|
|
|
|
You should avoid this kind of practice, and instead of electing a new
|
|
transfer in your tasklet, move that part to the interrupt handler in
|
|
order to have a shorter idle window (that we can't really avoid
|
|
anyway).
|
|
|
|
Glossary
|
|
========
|
|
|
|
- Burst: A number of consecutive read or write operations that
|
|
can be queued to buffers before being flushed to memory.
|
|
|
|
- Chunk: A contiguous collection of bursts
|
|
|
|
- Transfer: A collection of chunks (be it contiguous or not)
|