95 lines
2.2 KiB
C
95 lines
2.2 KiB
C
|
// SPDX-License-Identifier: GPL-2.0-only
|
||
|
|
/*
|
||
|
|
* Support for the S1 button on Routerboard 532
|
||
|
|
*
|
||
|
|
* Copyright (C) 2009 Phil Sutter <n0-1@freewrt.org>
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <linux/input.h>
|
||
|
|
#include <linux/module.h>
|
||
|
|
#include <linux/platform_device.h>
|
||
|
|
#include <linux/gpio.h>
|
||
|
|
|
||
|
|
#include <asm/mach-rc32434/gpio.h>
|
||
|
|
#include <asm/mach-rc32434/rb.h>
|
||
|
|
|
||
|
|
#define DRV_NAME "rb532-button"
|
||
|
|
|
||
|
|
#define RB532_BTN_RATE 100 /* msec */
|
||
|
|
#define RB532_BTN_KSYM BTN_0
|
||
|
|
|
||
|
|
/* The S1 button state is provided by GPIO pin 1. But as this
|
||
|
|
* pin is also used for uart input as alternate function, the
|
||
|
|
* operational modes must be switched first:
|
||
|
|
* 1) disable uart using set_latch_u5()
|
||
|
|
* 2) turn off alternate function implicitly through
|
||
|
|
* gpio_direction_input()
|
||
|
|
* 3) read the GPIO's current value
|
||
|
|
* 4) undo step 2 by enabling alternate function (in this
|
||
|
|
* mode the GPIO direction is fixed, so no change needed)
|
||
|
|
* 5) turn on uart again
|
||
|
|
* The GPIO value occurs to be inverted, so pin high means
|
||
|
|
* button is not pressed.
|
||
|
|
*/
|
||
|
|
static bool rb532_button_pressed(void)
|
||
|
|
{
|
||
|
|
int val;
|
||
|
|
|
||
|
|
set_latch_u5(0, LO_FOFF);
|
||
|
|
gpio_direction_input(GPIO_BTN_S1);
|
||
|
|
|
||
|
|
val = gpio_get_value(GPIO_BTN_S1);
|
||
|
|
|
||
|
|
rb532_gpio_set_func(GPIO_BTN_S1);
|
||
|
|
set_latch_u5(LO_FOFF, 0);
|
||
|
|
|
||
|
|
return !val;
|
||
|
|
}
|
||
|
|
|
||
|
|
static void rb532_button_poll(struct input_dev *input)
|
||
|
|
{
|
||
|
|
input_report_key(input, RB532_BTN_KSYM, rb532_button_pressed());
|
||
|
|
input_sync(input);
|
||
|
|
}
|
||
|
|
|
||
|
|
static int rb532_button_probe(struct platform_device *pdev)
|
||
|
|
{
|
||
|
|
struct input_dev *input;
|
||
|
|
int error;
|
||
|
|
|
||
|
|
input = devm_input_allocate_device(&pdev->dev);
|
||
|
|
if (!input)
|
||
|
|
return -ENOMEM;
|
||
|
|
|
||
|
|
input->name = "rb532 button";
|
||
|
|
input->phys = "rb532/button0";
|
||
|
|
input->id.bustype = BUS_HOST;
|
||
|
|
|
||
|
|
input_set_capability(input, EV_KEY, RB532_BTN_KSYM);
|
||
|
|
|
||
|
|
error = input_setup_polling(input, rb532_button_poll);
|
||
|
|
if (error)
|
||
|
|
return error;
|
||
|
|
|
||
|
|
input_set_poll_interval(input, RB532_BTN_RATE);
|
||
|
|
|
||
|
|
error = input_register_device(input);
|
||
|
|
if (error)
|
||
|
|
return error;
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
static struct platform_driver rb532_button_driver = {
|
||
|
|
.probe = rb532_button_probe,
|
||
|
|
.driver = {
|
||
|
|
.name = DRV_NAME,
|
||
|
|
},
|
||
|
|
};
|
||
|
|
module_platform_driver(rb532_button_driver);
|
||
|
|
|
||
|
|
MODULE_AUTHOR("Phil Sutter <n0-1@freewrt.org>");
|
||
|
|
MODULE_LICENSE("GPL");
|
||
|
|
MODULE_DESCRIPTION("Support for S1 button on Routerboard 532");
|
||
|
|
MODULE_ALIAS("platform:" DRV_NAME);
|