674 lines
16 KiB
Plaintext
674 lines
16 KiB
Plaintext
|
// SPDX-License-Identifier: GPL-2.0-only
|
||
|
|
/*
|
||
|
|
* Devicetree for the Samsung XCover 2 GT-S7710 also known as Skomer.
|
||
|
|
*/
|
||
|
|
|
||
|
|
/dts-v1/;
|
||
|
|
#include "ste-db8500.dtsi"
|
||
|
|
#include "ste-ab8505.dtsi"
|
||
|
|
#include "ste-dbx5x0-pinctrl.dtsi"
|
||
|
|
#include <dt-bindings/gpio/gpio.h>
|
||
|
|
#include <dt-bindings/leds/common.h>
|
||
|
|
#include <dt-bindings/input/input.h>
|
||
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
||
|
|
|
||
|
|
/ {
|
||
|
|
model = "Samsung XCover 2 (GT-S7710)";
|
||
|
|
compatible = "samsung,skomer", "st-ericsson,u8500";
|
||
|
|
|
||
|
|
chosen {
|
||
|
|
stdout-path = &serial2;
|
||
|
|
};
|
||
|
|
|
||
|
|
battery: battery {
|
||
|
|
compatible = "samsung,eb485159lu";
|
||
|
|
};
|
||
|
|
|
||
|
|
thermal-zones {
|
||
|
|
battery-thermal {
|
||
|
|
/* This zone will be polled by the battery temperature code */
|
||
|
|
polling-delay = <0>;
|
||
|
|
polling-delay-passive = <0>;
|
||
|
|
thermal-sensors = <&bat_therm>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
bat_therm: thermistor {
|
||
|
|
compatible = "samsung,1404-001221";
|
||
|
|
io-channels = <&gpadc 0x02>; /* BatTemp */
|
||
|
|
pullup-uv = <1800000>;
|
||
|
|
pullup-ohm = <230000>;
|
||
|
|
pulldown-ohm = <0>;
|
||
|
|
#thermal-sensor-cells = <0>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* TI TXS0206 level translator for 2.9 V */
|
||
|
|
sd_level_translator: regulator-gpio {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
|
||
|
|
/* GPIO87 EN */
|
||
|
|
gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
|
||
|
|
enable-active-high;
|
||
|
|
|
||
|
|
regulator-name = "sd-level-translator";
|
||
|
|
regulator-min-microvolt = <2900000>;
|
||
|
|
regulator-max-microvolt = <2900000>;
|
||
|
|
regulator-type = "voltage";
|
||
|
|
|
||
|
|
startup-delay-us = <200>;
|
||
|
|
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&sd_level_translator_default>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* External LDO MIC5366-3.3YMT for eMMC */
|
||
|
|
ldo_3v3_reg: regulator-gpio-ldo-3v3 {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-name = "en-3v3-fixed-supply";
|
||
|
|
regulator-min-microvolt = <3300000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
|
||
|
|
startup-delay-us = <5000>;
|
||
|
|
enable-active-high;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&emmc_ldo_en_default_mode>;
|
||
|
|
};
|
||
|
|
|
||
|
|
wlan_en: regulator-gpio-wlan-en {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-name = "wl-reg-on";
|
||
|
|
regulator-min-microvolt = <3000000>;
|
||
|
|
regulator-max-microvolt = <3000000>;
|
||
|
|
startup-delay-us = <200000>;
|
||
|
|
/* GPIO215 WLAN_EN */
|
||
|
|
gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
|
||
|
|
enable-active-high;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&wlan_en_default_mode>;
|
||
|
|
};
|
||
|
|
|
||
|
|
vibrator {
|
||
|
|
compatible = "gpio-vibrator";
|
||
|
|
enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&vibrator_default>;
|
||
|
|
};
|
||
|
|
|
||
|
|
gpio-keys {
|
||
|
|
compatible = "gpio-keys";
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&gpio_keys_default_mode>;
|
||
|
|
|
||
|
|
button-home {
|
||
|
|
linux,code = <KEY_HOME>;
|
||
|
|
label = "HOME";
|
||
|
|
/* GPIO91 */
|
||
|
|
gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
|
||
|
|
};
|
||
|
|
button-volup {
|
||
|
|
linux,code = <KEY_VOLUMEUP>;
|
||
|
|
label = "VOL+";
|
||
|
|
/* GPIO67 */
|
||
|
|
gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
|
||
|
|
};
|
||
|
|
button-voldown {
|
||
|
|
linux,code = <KEY_VOLUMEDOWN>;
|
||
|
|
label = "VOL-";
|
||
|
|
/* GPIO92 */
|
||
|
|
gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
|
||
|
|
};
|
||
|
|
button-menu {
|
||
|
|
linux,code = <KEY_MENU>;
|
||
|
|
label = "MENU";
|
||
|
|
/* GPIO204 */
|
||
|
|
gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
|
||
|
|
};
|
||
|
|
button-back {
|
||
|
|
linux,code = <KEY_BACK>;
|
||
|
|
label = "BACK";
|
||
|
|
/* GPIO205 */
|
||
|
|
gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
ktd253: backlight {
|
||
|
|
compatible = "kinetic,ktd253";
|
||
|
|
/* GPIO 69 */
|
||
|
|
enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
|
||
|
|
/* Default to 13/32 brightness */
|
||
|
|
default-brightness = <13>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&gpio_backlight_default_mode>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Richtek RT8515GQW Flash LED Driver IC */
|
||
|
|
flash {
|
||
|
|
compatible = "richtek,rt8515";
|
||
|
|
/* GPIO 140 */
|
||
|
|
enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
|
||
|
|
/* GPIO 141 */
|
||
|
|
ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
|
||
|
|
/*
|
||
|
|
* RFS is 16 kOhm and RTS is 100 kOhm giving
|
||
|
|
* the flash max current 343mA and torch max
|
||
|
|
* current 55 mA.
|
||
|
|
*/
|
||
|
|
richtek,rfs-ohms = <16000>;
|
||
|
|
richtek,rts-ohms = <100000>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&gpio_flash_default_mode>;
|
||
|
|
|
||
|
|
led {
|
||
|
|
function = LED_FUNCTION_FLASH;
|
||
|
|
color = <LED_COLOR_ID_WHITE>;
|
||
|
|
flash-max-timeout-us = <250000>;
|
||
|
|
flash-max-microamp = <343750>;
|
||
|
|
led-max-microamp = <55000>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
i2c-gpio-0 {
|
||
|
|
compatible = "i2c-gpio";
|
||
|
|
sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||
|
|
scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&i2c_gpio_0_default>;
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
/* TODO: this should be used by the NCP6914 Camera power management unit */
|
||
|
|
};
|
||
|
|
|
||
|
|
i2c-gpio-1 {
|
||
|
|
compatible = "i2c-gpio";
|
||
|
|
sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||
|
|
scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&i2c_gpio_1_default>;
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
magnetometer@c {
|
||
|
|
compatible = "alps,hscdtd008a";
|
||
|
|
reg = <0x0c>;
|
||
|
|
avdd-supply = <&ab8500_ldo_aux1_reg>;
|
||
|
|
dvdd-supply = <&ab8500_ldo_aux8_reg>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
soc {
|
||
|
|
// External Micro SD slot
|
||
|
|
mmc@80126000 {
|
||
|
|
arm,primecell-periphid = <0x10480180>;
|
||
|
|
max-frequency = <100000000>;
|
||
|
|
bus-width = <4>;
|
||
|
|
cap-sd-highspeed;
|
||
|
|
cap-mmc-highspeed;
|
||
|
|
/* All direction control is used */
|
||
|
|
st,sig-pin-fbclk;
|
||
|
|
full-pwr-cycle;
|
||
|
|
vmmc-supply = <&ab8500_ldo_aux3_reg>;
|
||
|
|
vqmmc-supply = <&sd_level_translator>;
|
||
|
|
pinctrl-names = "default", "sleep";
|
||
|
|
pinctrl-0 = <&mc0_a_1_default>;
|
||
|
|
pinctrl-1 = <&mc0_a_1_sleep>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
// WLAN SDIO channel
|
||
|
|
mmc@80118000 {
|
||
|
|
arm,primecell-periphid = <0x10480180>;
|
||
|
|
max-frequency = <50000000>;
|
||
|
|
bus-width = <4>;
|
||
|
|
non-removable;
|
||
|
|
cap-sd-highspeed;
|
||
|
|
vmmc-supply = <&wlan_en>;
|
||
|
|
pinctrl-names = "default", "sleep";
|
||
|
|
pinctrl-0 = <&mc1_a_2_default>;
|
||
|
|
pinctrl-1 = <&mc1_a_2_sleep>;
|
||
|
|
status = "okay";
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
|
||
|
|
wifi@1 {
|
||
|
|
compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
|
||
|
|
reg = <1>;
|
||
|
|
/* GPIO216 WL_HOST_WAKE */
|
||
|
|
interrupt-parent = <&gpio6>;
|
||
|
|
interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
|
||
|
|
interrupt-names = "host-wake";
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&wlan_default_mode>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/*
|
||
|
|
* eMMC seems to be mostly Samsung KLM4G1YE4C "4YMD1R"
|
||
|
|
*/
|
||
|
|
mmc@80005000 {
|
||
|
|
arm,primecell-periphid = <0x10480180>;
|
||
|
|
max-frequency = <100000000>;
|
||
|
|
bus-width = <8>;
|
||
|
|
non-removable;
|
||
|
|
cap-mmc-highspeed;
|
||
|
|
mmc-ddr-1_8v;
|
||
|
|
no-sdio;
|
||
|
|
no-sd;
|
||
|
|
/* From datasheet page 26 figure 9: 300 ms set-up time for 4GB */
|
||
|
|
post-power-on-delay-ms = <300>;
|
||
|
|
vmmc-supply = <&ldo_3v3_reg>;
|
||
|
|
pinctrl-names = "default", "sleep";
|
||
|
|
pinctrl-0 = <&mc2_a_1_default>;
|
||
|
|
pinctrl-1 = <&mc2_a_1_sleep>;
|
||
|
|
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* GBF (Bluetooth) UART */
|
||
|
|
uart@80120000 {
|
||
|
|
pinctrl-names = "default", "sleep";
|
||
|
|
pinctrl-0 = <&u0_a_1_default>;
|
||
|
|
pinctrl-1 = <&u0_a_1_sleep>;
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
/* FIXME: not quite working yet, probably needs regulators */
|
||
|
|
bluetooth {
|
||
|
|
/* BCM4334B0 actually */
|
||
|
|
compatible = "brcm,bcm4330-bt";
|
||
|
|
shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
|
||
|
|
device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
|
||
|
|
host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&bluetooth_default_mode>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/* GPF UART */
|
||
|
|
uart@80121000 {
|
||
|
|
status = "okay";
|
||
|
|
pinctrl-names = "default", "sleep";
|
||
|
|
pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
|
||
|
|
pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Debugging console UART connected to AB8505 USB */
|
||
|
|
uart@80007000 {
|
||
|
|
status = "okay";
|
||
|
|
pinctrl-names = "default", "sleep";
|
||
|
|
pinctrl-0 = <&u2rxtx_c_1_default>;
|
||
|
|
pinctrl-1 = <&u2rxtx_c_1_sleep>;
|
||
|
|
};
|
||
|
|
|
||
|
|
prcmu@80157000 {
|
||
|
|
ab8505 {
|
||
|
|
phy {
|
||
|
|
pinctrl-names = "default", "sleep";
|
||
|
|
pinctrl-0 = <&usb_a_1_default>;
|
||
|
|
pinctrl-1 = <&usb_a_1_sleep>;
|
||
|
|
};
|
||
|
|
|
||
|
|
regulator {
|
||
|
|
ab8500_ldo_aux1 {
|
||
|
|
/* Used for VDD for sensors */
|
||
|
|
regulator-name = "AUX1";
|
||
|
|
regulator-min-microvolt = <3000000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
ab8500_ldo_aux2 {
|
||
|
|
/* Supplies the Cypress TMA140 touchscreen only with 3.0V */
|
||
|
|
regulator-name = "AUX2";
|
||
|
|
regulator-min-microvolt = <3000000>;
|
||
|
|
regulator-max-microvolt = <3000000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
ab8500_ldo_aux3 {
|
||
|
|
/* Used for voltage for external MMC/SD card */
|
||
|
|
regulator-name = "AUX3";
|
||
|
|
regulator-min-microvolt = <1100000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
ab8500_ldo_aux4 {
|
||
|
|
regulator-name = "AUX4";
|
||
|
|
/* Hammer to 3.0V for the display */
|
||
|
|
regulator-min-microvolt = <3000000>;
|
||
|
|
regulator-max-microvolt = <3000000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
ab8500_ldo_aux5 {
|
||
|
|
regulator-name = "AUX5";
|
||
|
|
/* Intended for 1V8 for touchscreen but actually left unused */
|
||
|
|
regulator-min-microvolt = <1050000>;
|
||
|
|
regulator-max-microvolt = <2790000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
ab8500_ldo_aux6 {
|
||
|
|
regulator-name = "AUX6";
|
||
|
|
/* Hammer to 1.8V for the display */
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <1800000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
ab8500_ldo_aux8 {
|
||
|
|
/* Mostly VIO for sensors */
|
||
|
|
regulator-name = "AUX8";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/* I2C0 */
|
||
|
|
i2c@80004000 {
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
pinctrl-names = "default", "sleep";
|
||
|
|
pinctrl-0 = <&i2c0_a_1_default>;
|
||
|
|
pinctrl-1 = <&i2c0_a_1_sleep>;
|
||
|
|
|
||
|
|
proximity@44 {
|
||
|
|
compatible = "sharp,gp2ap002s00f";
|
||
|
|
clock-frequency = <400000>;
|
||
|
|
reg = <0x44>;
|
||
|
|
|
||
|
|
interrupt-parent = <&gpio4>;
|
||
|
|
interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
|
||
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
||
|
|
vio-supply = <&ab8500_ldo_aux8_reg>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&gp2ap002_skomer_default>;
|
||
|
|
sharp,proximity-far-hysteresis = /bits/ 8 <0x2f>;
|
||
|
|
sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
|
||
|
|
/* I2C2 */
|
||
|
|
i2c@80128000 {
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
pinctrl-names = "default", "sleep";
|
||
|
|
pinctrl-0 = <&i2c2_b_2_default>;
|
||
|
|
pinctrl-1 = <&i2c2_b_2_sleep>;
|
||
|
|
|
||
|
|
accel@18 {
|
||
|
|
compatible = "bosch,bma254";
|
||
|
|
clock-frequency = <400000>;
|
||
|
|
reg = <0x18>;
|
||
|
|
|
||
|
|
/* GPIO224 used as "smart alert" interrupt */
|
||
|
|
interrupt-parent = <&gpio7>;
|
||
|
|
interrupts = <0 IRQ_TYPE_EDGE_RISING>;
|
||
|
|
|
||
|
|
mount-matrix = "0", "-1", "0",
|
||
|
|
"1", "0", "0",
|
||
|
|
"0", "0", "1";
|
||
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
||
|
|
vddio-supply = <&ab8500_ldo_aux8_reg>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&bma254_skomer_default>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/* I2C3 */
|
||
|
|
i2c@80110000 {
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
pinctrl-names = "default", "sleep";
|
||
|
|
pinctrl-0 = <&i2c3_c_2_default>;
|
||
|
|
pinctrl-1 = <&i2c3_c_2_sleep>;
|
||
|
|
|
||
|
|
/* Cypress CY8CTMA140 touchscreen */
|
||
|
|
touchscreen@20 {
|
||
|
|
compatible = "cypress,cy8ctma140";
|
||
|
|
clock-frequency = <400000>;
|
||
|
|
reg = <0x20>;
|
||
|
|
|
||
|
|
touchscreen-size-x = <480>;
|
||
|
|
touchscreen-size-y = <800>;
|
||
|
|
touchscreen-max-pressure = <255>;
|
||
|
|
|
||
|
|
/* GPIO218 for IRQ */
|
||
|
|
interrupt-parent = <&gpio6>;
|
||
|
|
interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
|
||
|
|
|
||
|
|
/* VDD is "digital supply" nominally 1.71-3.6V */
|
||
|
|
vdd-supply = <&ab8500_ldo_aux2_reg>;
|
||
|
|
/* VCPIN is "analog supply", 2.7-3.6 V */
|
||
|
|
vcpin-supply = <&ab8500_ldo_aux2_reg>;
|
||
|
|
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&tma140_skomer_default>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
mcde@a0350000 {
|
||
|
|
status = "okay";
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&dsi_default_mode>;
|
||
|
|
|
||
|
|
dsi@a0351000 {
|
||
|
|
panel {
|
||
|
|
/* NT35510-based Hydis HVA40WV1 */
|
||
|
|
compatible = "hydis,hva40wv1", "novatek,nt35510";
|
||
|
|
reg = <0>;
|
||
|
|
/* v_lcd_3v0 2.3-4.8V */
|
||
|
|
vdd-supply = <&ab8500_ldo_aux4_reg>;
|
||
|
|
/* v_lcd_1v8 1.65-3.3V */
|
||
|
|
vddi-supply = <&ab8500_ldo_aux6_reg>;
|
||
|
|
/* GPIO 139 */
|
||
|
|
reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&display_default_mode>;
|
||
|
|
backlight = <&ktd253>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&pinctrl {
|
||
|
|
sdi0 {
|
||
|
|
mc0_a_1_default {
|
||
|
|
default_cfg1 {
|
||
|
|
/* GPIO18, 19 & 20 unused so pull down */
|
||
|
|
ste,config = <&gpio_in_pd>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/* This is a reset line for the eMMC */
|
||
|
|
sdi2 {
|
||
|
|
mc2_a_1_default {
|
||
|
|
default_cfg2 {
|
||
|
|
pins = "GPIO130_C8"; /* FBCLK */
|
||
|
|
ste,config = <&gpio_in_pd>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
mcde {
|
||
|
|
dsi_default_mode: dsi_default {
|
||
|
|
default_mux1 {
|
||
|
|
/* Mux in VSI0 used for DSI TE */
|
||
|
|
function = "lcd";
|
||
|
|
groups = "lcdvsi0_a_1"; /* VSI0 for LCD */
|
||
|
|
};
|
||
|
|
default_cfg1 {
|
||
|
|
pins = "GPIO68_E1"; /* VSI0 */
|
||
|
|
ste,config = <&in_nopull>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Two GPIO lines used by the display */
|
||
|
|
display {
|
||
|
|
display_default_mode: display_default {
|
||
|
|
skomer_cfg1 {
|
||
|
|
/*
|
||
|
|
* OLED DETECT or check_pba, this appears to be high
|
||
|
|
* on "PBA" which I guess is "prototype board A".
|
||
|
|
*/
|
||
|
|
pins = "GPIO93_B7";
|
||
|
|
ste,config = <&gpio_in_nopull>;
|
||
|
|
};
|
||
|
|
skomer_cfg2 {
|
||
|
|
pins = "GPIO139_C9";
|
||
|
|
/*
|
||
|
|
* MIPI_DSI0_RESET_N resets the display, leave high
|
||
|
|
* (de-asserted) so we only assert reset explicitly
|
||
|
|
* from the display driver.
|
||
|
|
*/
|
||
|
|
ste,config = <&gpio_out_hi>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
backlight {
|
||
|
|
gpio_backlight_default_mode: backlight_default {
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO69_E2"; /* LCD_BL_CTRL */
|
||
|
|
ste,config = <&gpio_out_lo>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
flash {
|
||
|
|
gpio_flash_default_mode: flash_default {
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO140_B11", "GPIO141_C12";
|
||
|
|
ste,config = <&gpio_out_lo>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
/* GPIO that enables the 2.9V SD card level translator */
|
||
|
|
sd-level-translator {
|
||
|
|
sd_level_translator_default: sd_level_translator_default {
|
||
|
|
/* level shifter on GPIO87 */
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO87_B3";
|
||
|
|
ste,config = <&gpio_out_hi>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
/* GPIO that enables the LDO regulator for the eMMC */
|
||
|
|
emmc-ldo {
|
||
|
|
emmc_ldo_en_default_mode: emmc_ldo_default {
|
||
|
|
/* LDO enable on GPIO223 */
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO223_AH9";
|
||
|
|
ste,config = <&gpio_out_hi>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
/* GPIO keys */
|
||
|
|
gpio-keys {
|
||
|
|
gpio_keys_default_mode: gpio_keys_default {
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO67_G2", /* VOL UP */
|
||
|
|
"GPIO91_B6", /* HOME */
|
||
|
|
"GPIO92_D6", /* VOL DOWN */
|
||
|
|
"GPIO204_AF23", /* MENU */
|
||
|
|
"GPIO205_AG23"; /* BACK */
|
||
|
|
ste,config = <&gpio_in_pu>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
/* Interrupt line for BMA254 */
|
||
|
|
bma254 {
|
||
|
|
bma254_skomer_default: bma254_skomer {
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO224_AG9";
|
||
|
|
ste,config = <&gpio_in_pd>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
/* Interrupt line for light/proximity sensor GP2AP002 */
|
||
|
|
gp2ap002 {
|
||
|
|
gp2ap002_skomer_default: gp2ap002_skomer {
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO146_D13";
|
||
|
|
ste,config = <&gpio_in_nopull>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
/* GPIO-based I2C bus for NCP6914 */
|
||
|
|
i2c-gpio-0 {
|
||
|
|
i2c_gpio_0_default: i2c_gpio_0 {
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO143_D12", "GPIO144_B13";
|
||
|
|
ste,config = <&gpio_in_nopull>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
/* GPIO-based I2C bus for ALPS HSCD compass */
|
||
|
|
i2c-gpio-1 {
|
||
|
|
i2c_gpio_1_default: i2c_gpio_1 {
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO151_B17", "GPIO152_D16";
|
||
|
|
ste,config = <&gpio_in_nopull>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
wlan {
|
||
|
|
wlan_default_mode: wlan_default {
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO216_AG12";
|
||
|
|
ste,config = <&gpio_in_pd>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
wlan_en_default_mode: wlan_en_default {
|
||
|
|
skomer_cfg2 {
|
||
|
|
pins = "GPIO215_AH13";
|
||
|
|
ste,config = <&gpio_out_lo>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
bluetooth {
|
||
|
|
bluetooth_default_mode: bluetooth_default {
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO199_AH23", "GPIO222_AJ9";
|
||
|
|
ste,config = <&gpio_out_lo>;
|
||
|
|
};
|
||
|
|
skomer_cfg2 {
|
||
|
|
pins = "GPIO97_D9";
|
||
|
|
ste,config = <&gpio_in_nopull>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
vibrator {
|
||
|
|
vibrator_default: vibrator_default {
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO195_AG28"; /* MOT_EN */
|
||
|
|
ste,config = <&gpio_out_lo>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
/* Interrupt line for the Cypress TMA140 touchscreen */
|
||
|
|
touchscreen {
|
||
|
|
tma140_skomer_default: tma140_skomer {
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO218_AH11";
|
||
|
|
ste,config = <&gpio_in_nopull>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&ab8505_gpio {
|
||
|
|
/* Hog a few default settings */
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&gpio_default>;
|
||
|
|
|
||
|
|
gpio {
|
||
|
|
gpio_default: gpio_default {
|
||
|
|
skomer_mux {
|
||
|
|
/* Change unused pins to GPIO mode */
|
||
|
|
function = "gpio";
|
||
|
|
groups = "gpio3_a_1", /* default: SysClkReq4 */
|
||
|
|
"gpio14_a_1"; /* default: PWMOut1 */
|
||
|
|
};
|
||
|
|
skomer_cfg1 {
|
||
|
|
pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4";
|
||
|
|
bias-disable;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|