313 lines
7.0 KiB
Plaintext
313 lines
7.0 KiB
Plaintext
|
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||
|
|
/*
|
||
|
|
* Device Tree file for Synology DS213j
|
||
|
|
*
|
||
|
|
* Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org>
|
||
|
|
*
|
||
|
|
* Note: this Device Tree assumes that the bootloader has remapped the
|
||
|
|
* internal registers to 0xf1000000 (instead of the old 0xd0000000).
|
||
|
|
* The 0xf1000000 is the default used by the recent, DT-capable, U-Boot
|
||
|
|
* bootloaders provided by Marvell. It is used in recent versions of
|
||
|
|
* DSM software provided by Synology. Nonetheless, some earlier boards
|
||
|
|
* were delivered with an older version of u-boot that left internal
|
||
|
|
* registers mapped at 0xd0000000. If you have such a device you will
|
||
|
|
* not be able to directly boot a kernel based on this Device Tree. In
|
||
|
|
* that case, the preferred solution is to update your bootloader (e.g.
|
||
|
|
* by upgrading to latest version of DSM, or building a new one and
|
||
|
|
* installing it from u-boot prompt) or adjust the Devive Tree
|
||
|
|
* (s/0xf1000000/0xd0000000/ in 'ranges' below).
|
||
|
|
*/
|
||
|
|
|
||
|
|
/dts-v1/;
|
||
|
|
|
||
|
|
#include <dt-bindings/input/input.h>
|
||
|
|
#include <dt-bindings/gpio/gpio.h>
|
||
|
|
#include "armada-370.dtsi"
|
||
|
|
|
||
|
|
/ {
|
||
|
|
model = "Synology DS213j";
|
||
|
|
compatible = "synology,ds213j", "marvell,armada370",
|
||
|
|
"marvell,armada-370-xp";
|
||
|
|
|
||
|
|
chosen {
|
||
|
|
stdout-path = "serial0:115200n8";
|
||
|
|
};
|
||
|
|
|
||
|
|
memory@0 {
|
||
|
|
device_type = "memory";
|
||
|
|
reg = <0x00000000 0x20000000>; /* 512 MB */
|
||
|
|
};
|
||
|
|
|
||
|
|
soc {
|
||
|
|
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
|
||
|
|
MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
|
||
|
|
MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
|
||
|
|
|
||
|
|
internal-regs {
|
||
|
|
|
||
|
|
/* RTC provided by Seiko S-35390A I2C RTC chip below */
|
||
|
|
rtc@10300 {
|
||
|
|
status = "disabled";
|
||
|
|
};
|
||
|
|
|
||
|
|
i2c@11000 {
|
||
|
|
compatible = "marvell,mv64xxx-i2c";
|
||
|
|
pinctrl-0 = <&i2c0_pins>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
clock-frequency = <400000>;
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
/* Main device RTC chip */
|
||
|
|
s35390a: s35390a@30 {
|
||
|
|
compatible = "sii,s35390a";
|
||
|
|
reg = <0x30>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Connected to a header on device's PCB */
|
||
|
|
serial@12000 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Connected to a TI MSP430F2111 for power control */
|
||
|
|
serial@12100 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
poweroff@12100 {
|
||
|
|
compatible = "synology,power-off";
|
||
|
|
reg = <0x12100 0x100>;
|
||
|
|
clocks = <&coreclk 0>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* rear USB port, near reset button */
|
||
|
|
usb@50000 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* rear USB port, near RJ45 port */
|
||
|
|
usb@51000 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
ethernet@70000 {
|
||
|
|
status = "okay";
|
||
|
|
phy = <&phy1>;
|
||
|
|
phy-mode = "sgmii";
|
||
|
|
};
|
||
|
|
|
||
|
|
sata@a0000 {
|
||
|
|
nr-ports = <2>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
gpio-fan-32-38 {
|
||
|
|
status = "okay";
|
||
|
|
compatible = "gpio-fan";
|
||
|
|
pinctrl-0 = <&fan_ctrl_low_pin &fan_ctrl_mid_pin
|
||
|
|
&fan_ctrl_high_pin &fan_alarm_pin>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
gpios = <&gpio1 31 GPIO_ACTIVE_HIGH
|
||
|
|
&gpio2 0 GPIO_ACTIVE_HIGH
|
||
|
|
&gpio2 1 GPIO_ACTIVE_HIGH>;
|
||
|
|
alarm-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
|
||
|
|
gpio-fan,speed-map = < 0 0
|
||
|
|
1000 1
|
||
|
|
1150 2
|
||
|
|
1350 4
|
||
|
|
1500 3
|
||
|
|
1650 5
|
||
|
|
1750 6
|
||
|
|
1900 7 >;
|
||
|
|
};
|
||
|
|
|
||
|
|
gpio-leds {
|
||
|
|
compatible = "gpio-leds";
|
||
|
|
pinctrl-0 = <&disk1_led_pin
|
||
|
|
&disk2_led_pin>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
|
||
|
|
disk1-led-amber {
|
||
|
|
label = "synology:amber:disk1";
|
||
|
|
gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
|
||
|
|
default-state = "keep";
|
||
|
|
};
|
||
|
|
|
||
|
|
disk2-led-amber {
|
||
|
|
label = "synology:amber:disk2";
|
||
|
|
gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
|
||
|
|
default-state = "keep";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
regulators {
|
||
|
|
compatible = "simple-bus";
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
|
||
|
|
sata1_regulator: sata1-regulator@1 {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
reg = <1>;
|
||
|
|
regulator-name = "SATA1 Power";
|
||
|
|
regulator-min-microvolt = <5000000>;
|
||
|
|
regulator-max-microvolt = <5000000>;
|
||
|
|
startup-delay-us = <2000000>;
|
||
|
|
enable-active-high;
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
|
||
|
|
};
|
||
|
|
|
||
|
|
sata2_regulator: sata2-regulator@2 {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
reg = <2>;
|
||
|
|
regulator-name = "SATA2 Power";
|
||
|
|
regulator-min-microvolt = <5000000>;
|
||
|
|
regulator-max-microvolt = <5000000>;
|
||
|
|
startup-delay-us = <4000000>;
|
||
|
|
enable-active-high;
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&mdio {
|
||
|
|
phy1: ethernet-phy@1 { /* Marvell 88E1512 */
|
||
|
|
reg = <1>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&pinctrl {
|
||
|
|
disk1_led_pin: disk1-led-pin {
|
||
|
|
marvell,pins = "mpp31";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
disk2_led_pin: disk2-led-pin {
|
||
|
|
marvell,pins = "mpp32";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
sata1_pwr_pin: sata1-pwr-pin {
|
||
|
|
marvell,pins = "mpp37";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
sata2_pwr_pin: sata2-pwr-pin {
|
||
|
|
marvell,pins = "mpp62";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
sata1_pres_pin: sata1-pres-pin {
|
||
|
|
marvell,pins = "mpp60";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
sata2_pres_pin: sata2-pres-pin {
|
||
|
|
marvell,pins = "mpp48";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
syno_id_bit0_pin: syno-id-bit0-pin {
|
||
|
|
marvell,pins = "mpp55";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
syno_id_bit1_pin: syno-id-bit1-pin {
|
||
|
|
marvell,pins = "mpp56";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
syno_id_bit2_pin: syno-id-bit2-pin {
|
||
|
|
marvell,pins = "mpp57";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
syno_id_bit3_pin: syno-id-bit3-pin {
|
||
|
|
marvell,pins = "mpp58";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
fan_ctrl_low_pin: fan-ctrl-low-pin {
|
||
|
|
marvell,pins = "mpp65";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
fan_ctrl_mid_pin: fan-ctrl-mid-pin {
|
||
|
|
marvell,pins = "mpp64";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
fan_ctrl_high_pin: fan-ctrl-high-pin {
|
||
|
|
marvell,pins = "mpp63";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
fan_alarm_pin: fan-alarm-pin {
|
||
|
|
marvell,pins = "mpp38";
|
||
|
|
marvell,function = "gpio";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&spi0 {
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
spi-flash@0 {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <1>;
|
||
|
|
compatible = "micron,n25q064", "jedec,spi-nor";
|
||
|
|
reg = <0>; /* Chip select 0 */
|
||
|
|
spi-max-frequency = <20000000>;
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Warning!
|
||
|
|
*
|
||
|
|
* Synology u-boot uses its compiled-in environment
|
||
|
|
* and it seems Synology did not care to change u-boot
|
||
|
|
* default configuration in order to allow saving a
|
||
|
|
* modified environment at a sensible location. So,
|
||
|
|
* if you do a 'saveenv' under u-boot, your modified
|
||
|
|
* environment will be saved at 1MB after the start
|
||
|
|
* of the flash, i.e. in the middle of the uImage.
|
||
|
|
* For that reason, it is strongly advised not to
|
||
|
|
* change the default environment, unless you know
|
||
|
|
* what you are doing.
|
||
|
|
*/
|
||
|
|
partition@0 { /* u-boot */
|
||
|
|
label = "RedBoot";
|
||
|
|
reg = <0x00000000 0x000c0000>; /* 768KB */
|
||
|
|
};
|
||
|
|
|
||
|
|
partition@c0000 { /* uImage */
|
||
|
|
label = "zImage";
|
||
|
|
reg = <0x000c0000 0x002d0000>; /* 2880KB */
|
||
|
|
};
|
||
|
|
|
||
|
|
partition@390000 { /* uInitramfs */
|
||
|
|
label = "rd.gz";
|
||
|
|
reg = <0x00390000 0x00440000>; /* 4250KB */
|
||
|
|
};
|
||
|
|
|
||
|
|
partition@7d0000 { /* MAC address and serial number */
|
||
|
|
label = "vendor";
|
||
|
|
reg = <0x007d0000 0x00010000>; /* 64KB */
|
||
|
|
};
|
||
|
|
|
||
|
|
partition@7e0000 {
|
||
|
|
label = "RedBoot config";
|
||
|
|
reg = <0x007e0000 0x00010000>; /* 64KB */
|
||
|
|
};
|
||
|
|
|
||
|
|
partition@7f0000 {
|
||
|
|
label = "FIS directory";
|
||
|
|
reg = <0x007f0000 0x00010000>; /* 64KB */
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|