88 lines
1.5 KiB
Plaintext
88 lines
1.5 KiB
Plaintext
|
// SPDX-License-Identifier: GPL-2.0-only
|
||
|
|
/*
|
||
|
|
* Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
* VScom OnRISC
|
||
|
|
* http://www.vscom.de
|
||
|
|
*/
|
||
|
|
|
||
|
|
/dts-v1/;
|
||
|
|
|
||
|
|
#include "am335x-baltos.dtsi"
|
||
|
|
#include "am335x-baltos-leds.dtsi"
|
||
|
|
|
||
|
|
/ {
|
||
|
|
model = "NetCAN";
|
||
|
|
|
||
|
|
leds {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&user_leds_s0>;
|
||
|
|
|
||
|
|
compatible = "gpio-leds";
|
||
|
|
|
||
|
|
led@1 {
|
||
|
|
label = "can_data";
|
||
|
|
linux,default-trigger = "netdev";
|
||
|
|
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
||
|
|
default-state = "off";
|
||
|
|
};
|
||
|
|
led@2 {
|
||
|
|
label = "can_error";
|
||
|
|
gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
|
||
|
|
default-state = "off";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&am33xx_pinmux {
|
||
|
|
user_leds_s0: user_leds_s0 {
|
||
|
|
pinctrl-single,pins = <
|
||
|
|
AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* CAN Data LED */
|
||
|
|
AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* CAN Error LED */
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
dcan1_pins: pinmux_dcan1_pins {
|
||
|
|
pinctrl-single,pins = <
|
||
|
|
AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT, MUX_MODE2) /* CAN TX */
|
||
|
|
AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE2) /* CAN RX */
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb0_phy {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb0 {
|
||
|
|
status = "okay";
|
||
|
|
dr_mode = "host";
|
||
|
|
};
|
||
|
|
|
||
|
|
&davinci_mdio_sw {
|
||
|
|
phy0: ethernet-phy@0 {
|
||
|
|
reg = <1>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&cpsw_port1 {
|
||
|
|
phy-mode = "rmii";
|
||
|
|
ti,dual-emac-pvid = <1>;
|
||
|
|
phy-handle = <&phy0>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&cpsw_port2 {
|
||
|
|
phy-mode = "rgmii-id";
|
||
|
|
ti,dual-emac-pvid = <2>;
|
||
|
|
phy-handle = <&phy1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&dcan1 {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&dcan1_pins>;
|
||
|
|
|
||
|
|
status = "okay";
|
||
|
|
};
|