78 lines
2.8 KiB
ReStructuredText
78 lines
2.8 KiB
ReStructuredText
|
.. SPDX-License-Identifier: GPL-2.0
|
||
|
|
|
||
|
|
=======================================
|
||
|
|
Internal ABI between the kernel and HYP
|
||
|
|
=======================================
|
||
|
|
|
||
|
|
This file documents the interaction between the Linux kernel and the
|
||
|
|
hypervisor layer when running Linux as a hypervisor (for example
|
||
|
|
KVM). It doesn't cover the interaction of the kernel with the
|
||
|
|
hypervisor when running as a guest (under Xen, KVM or any other
|
||
|
|
hypervisor), or any hypervisor-specific interaction when the kernel is
|
||
|
|
used as a host.
|
||
|
|
|
||
|
|
Note: KVM/arm has been removed from the kernel. The API described
|
||
|
|
here is still valid though, as it allows the kernel to kexec when
|
||
|
|
booted at HYP. It can also be used by a hypervisor other than KVM
|
||
|
|
if necessary.
|
||
|
|
|
||
|
|
On arm and arm64 (without VHE), the kernel doesn't run in hypervisor
|
||
|
|
mode, but still needs to interact with it, allowing a built-in
|
||
|
|
hypervisor to be either installed or torn down.
|
||
|
|
|
||
|
|
In order to achieve this, the kernel must be booted at HYP (arm) or
|
||
|
|
EL2 (arm64), allowing it to install a set of stubs before dropping to
|
||
|
|
SVC/EL1. These stubs are accessible by using a 'hvc #0' instruction,
|
||
|
|
and only act on individual CPUs.
|
||
|
|
|
||
|
|
Unless specified otherwise, any built-in hypervisor must implement
|
||
|
|
these functions (see arch/arm{,64}/include/asm/virt.h):
|
||
|
|
|
||
|
|
* ::
|
||
|
|
|
||
|
|
r0/x0 = HVC_SET_VECTORS
|
||
|
|
r1/x1 = vectors
|
||
|
|
|
||
|
|
Set HVBAR/VBAR_EL2 to 'vectors' to enable a hypervisor. 'vectors'
|
||
|
|
must be a physical address, and respect the alignment requirements
|
||
|
|
of the architecture. Only implemented by the initial stubs, not by
|
||
|
|
Linux hypervisors.
|
||
|
|
|
||
|
|
* ::
|
||
|
|
|
||
|
|
r0/x0 = HVC_RESET_VECTORS
|
||
|
|
|
||
|
|
Turn HYP/EL2 MMU off, and reset HVBAR/VBAR_EL2 to the initials
|
||
|
|
stubs' exception vector value. This effectively disables an existing
|
||
|
|
hypervisor.
|
||
|
|
|
||
|
|
* ::
|
||
|
|
|
||
|
|
r0/x0 = HVC_SOFT_RESTART
|
||
|
|
r1/x1 = restart address
|
||
|
|
x2 = x0's value when entering the next payload (arm64)
|
||
|
|
x3 = x1's value when entering the next payload (arm64)
|
||
|
|
x4 = x2's value when entering the next payload (arm64)
|
||
|
|
|
||
|
|
Mask all exceptions, disable the MMU, clear I+D bits, move the arguments
|
||
|
|
into place (arm64 only), and jump to the restart address while at HYP/EL2.
|
||
|
|
This hypercall is not expected to return to its caller.
|
||
|
|
|
||
|
|
* ::
|
||
|
|
|
||
|
|
x0 = HVC_VHE_RESTART (arm64 only)
|
||
|
|
|
||
|
|
Attempt to upgrade the kernel's exception level from EL1 to EL2 by enabling
|
||
|
|
the VHE mode. This is conditioned by the CPU supporting VHE, the EL2 MMU
|
||
|
|
being off, and VHE not being disabled by any other means (command line
|
||
|
|
option, for example).
|
||
|
|
|
||
|
|
Any other value of r0/x0 triggers a hypervisor-specific handling,
|
||
|
|
which is not documented here.
|
||
|
|
|
||
|
|
The return value of a stub hypercall is held by r0/x0, and is 0 on
|
||
|
|
success, and HVC_STUB_ERR on error. A stub hypercall is allowed to
|
||
|
|
clobber any of the caller-saved registers (x0-x18 on arm64, r0-r3 and
|
||
|
|
ip on arm). It is thus recommended to use a function call to perform
|
||
|
|
the hypercall.
|