219 lines
6.0 KiB
C
219 lines
6.0 KiB
C
/*
|
|
* Copyright (C) 2005-2006 Micronas USA Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License (Version 2) as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/list.h>
|
|
#include <linux/unistd.h>
|
|
#include <linux/time.h>
|
|
#include <linux/device.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/mutex.h>
|
|
#include <linux/uaccess.h>
|
|
|
|
#include "go7007-priv.h"
|
|
|
|
/********************* Driver for on-board I2C adapter *********************/
|
|
|
|
/* #define GO7007_I2C_DEBUG */
|
|
|
|
#define SPI_I2C_ADDR_BASE 0x1400
|
|
#define STATUS_REG_ADDR (SPI_I2C_ADDR_BASE + 0x2)
|
|
#define I2C_CTRL_REG_ADDR (SPI_I2C_ADDR_BASE + 0x6)
|
|
#define I2C_DEV_UP_ADDR_REG_ADDR (SPI_I2C_ADDR_BASE + 0x7)
|
|
#define I2C_LO_ADDR_REG_ADDR (SPI_I2C_ADDR_BASE + 0x8)
|
|
#define I2C_DATA_REG_ADDR (SPI_I2C_ADDR_BASE + 0x9)
|
|
#define I2C_CLKFREQ_REG_ADDR (SPI_I2C_ADDR_BASE + 0xa)
|
|
|
|
#define I2C_STATE_MASK 0x0007
|
|
#define I2C_READ_READY_MASK 0x0008
|
|
|
|
/* There is only one I2C port on the TW2804 that feeds all four GO7007 VIPs
|
|
* on the Adlink PCI-MPG24, so access is shared between all of them. */
|
|
static DEFINE_MUTEX(adlink_mpg24_i2c_lock);
|
|
|
|
static int go7007_i2c_xfer(struct go7007 *go, u16 addr, int read,
|
|
u16 command, int flags, u8 *data)
|
|
{
|
|
int i, ret = -EIO;
|
|
u16 val;
|
|
|
|
if (go->status == STATUS_SHUTDOWN)
|
|
return -ENODEV;
|
|
|
|
#ifdef GO7007_I2C_DEBUG
|
|
if (read)
|
|
dev_dbg(go->dev, "go7007-i2c: reading 0x%02x on 0x%02x\n",
|
|
command, addr);
|
|
else
|
|
dev_dbg(go->dev,
|
|
"go7007-i2c: writing 0x%02x to 0x%02x on 0x%02x\n",
|
|
*data, command, addr);
|
|
#endif
|
|
|
|
mutex_lock(&go->hw_lock);
|
|
|
|
if (go->board_id == GO7007_BOARDID_ADLINK_MPG24) {
|
|
/* Bridge the I2C port on this GO7007 to the shared bus */
|
|
mutex_lock(&adlink_mpg24_i2c_lock);
|
|
go7007_write_addr(go, 0x3c82, 0x0020);
|
|
}
|
|
|
|
/* Wait for I2C adapter to be ready */
|
|
for (i = 0; i < 10; ++i) {
|
|
if (go7007_read_addr(go, STATUS_REG_ADDR, &val) < 0)
|
|
goto i2c_done;
|
|
if (!(val & I2C_STATE_MASK))
|
|
break;
|
|
msleep(100);
|
|
}
|
|
if (i == 10) {
|
|
dev_err(go->dev, "go7007-i2c: I2C adapter is hung\n");
|
|
goto i2c_done;
|
|
}
|
|
|
|
/* Set target register (command) */
|
|
go7007_write_addr(go, I2C_CTRL_REG_ADDR, flags);
|
|
go7007_write_addr(go, I2C_LO_ADDR_REG_ADDR, command);
|
|
|
|
/* If we're writing, send the data and target address and we're done */
|
|
if (!read) {
|
|
go7007_write_addr(go, I2C_DATA_REG_ADDR, *data);
|
|
go7007_write_addr(go, I2C_DEV_UP_ADDR_REG_ADDR,
|
|
(addr << 9) | (command >> 8));
|
|
ret = 0;
|
|
goto i2c_done;
|
|
}
|
|
|
|
/* Otherwise, we're reading. First clear i2c_rx_data_rdy. */
|
|
if (go7007_read_addr(go, I2C_DATA_REG_ADDR, &val) < 0)
|
|
goto i2c_done;
|
|
|
|
/* Send the target address plus read flag */
|
|
go7007_write_addr(go, I2C_DEV_UP_ADDR_REG_ADDR,
|
|
(addr << 9) | 0x0100 | (command >> 8));
|
|
|
|
/* Wait for i2c_rx_data_rdy */
|
|
for (i = 0; i < 10; ++i) {
|
|
if (go7007_read_addr(go, STATUS_REG_ADDR, &val) < 0)
|
|
goto i2c_done;
|
|
if (val & I2C_READ_READY_MASK)
|
|
break;
|
|
msleep(100);
|
|
}
|
|
if (i == 10) {
|
|
dev_err(go->dev, "go7007-i2c: I2C adapter is hung\n");
|
|
goto i2c_done;
|
|
}
|
|
|
|
/* Retrieve the read byte */
|
|
if (go7007_read_addr(go, I2C_DATA_REG_ADDR, &val) < 0)
|
|
goto i2c_done;
|
|
*data = val;
|
|
ret = 0;
|
|
|
|
i2c_done:
|
|
if (go->board_id == GO7007_BOARDID_ADLINK_MPG24) {
|
|
/* Isolate the I2C port on this GO7007 from the shared bus */
|
|
go7007_write_addr(go, 0x3c82, 0x0000);
|
|
mutex_unlock(&adlink_mpg24_i2c_lock);
|
|
}
|
|
mutex_unlock(&go->hw_lock);
|
|
return ret;
|
|
}
|
|
|
|
static int go7007_smbus_xfer(struct i2c_adapter *adapter, u16 addr,
|
|
unsigned short flags, char read_write,
|
|
u8 command, int size, union i2c_smbus_data *data)
|
|
{
|
|
struct go7007 *go = i2c_get_adapdata(adapter);
|
|
|
|
if (size != I2C_SMBUS_BYTE_DATA)
|
|
return -EIO;
|
|
return go7007_i2c_xfer(go, addr, read_write == I2C_SMBUS_READ, command,
|
|
flags & I2C_CLIENT_SCCB ? 0x10 : 0x00, &data->byte);
|
|
}
|
|
|
|
/* VERY LIMITED I2C master xfer function -- only needed because the
|
|
* SMBus functions only support 8-bit commands and the SAA7135 uses
|
|
* 16-bit commands. The I2C interface on the GO7007, as limited as
|
|
* it is, does support this mode. */
|
|
|
|
static int go7007_i2c_master_xfer(struct i2c_adapter *adapter,
|
|
struct i2c_msg msgs[], int num)
|
|
{
|
|
struct go7007 *go = i2c_get_adapdata(adapter);
|
|
int i;
|
|
|
|
for (i = 0; i < num; ++i) {
|
|
/* We can only do two things here -- write three bytes, or
|
|
* write two bytes and read one byte. */
|
|
if (msgs[i].len == 2) {
|
|
if (i + 1 == num || msgs[i].addr != msgs[i + 1].addr ||
|
|
(msgs[i].flags & I2C_M_RD) ||
|
|
!(msgs[i + 1].flags & I2C_M_RD) ||
|
|
msgs[i + 1].len != 1)
|
|
return -EIO;
|
|
if (go7007_i2c_xfer(go, msgs[i].addr, 1,
|
|
(msgs[i].buf[0] << 8) | msgs[i].buf[1],
|
|
0x01, &msgs[i + 1].buf[0]) < 0)
|
|
return -EIO;
|
|
++i;
|
|
} else if (msgs[i].len == 3) {
|
|
if (msgs[i].flags & I2C_M_RD)
|
|
return -EIO;
|
|
if (msgs[i].len != 3)
|
|
return -EIO;
|
|
if (go7007_i2c_xfer(go, msgs[i].addr, 0,
|
|
(msgs[i].buf[0] << 8) | msgs[i].buf[1],
|
|
0x01, &msgs[i].buf[2]) < 0)
|
|
return -EIO;
|
|
} else
|
|
return -EIO;
|
|
}
|
|
|
|
return num;
|
|
}
|
|
|
|
static u32 go7007_functionality(struct i2c_adapter *adapter)
|
|
{
|
|
return I2C_FUNC_SMBUS_BYTE_DATA;
|
|
}
|
|
|
|
static const struct i2c_algorithm go7007_algo = {
|
|
.smbus_xfer = go7007_smbus_xfer,
|
|
.master_xfer = go7007_i2c_master_xfer,
|
|
.functionality = go7007_functionality,
|
|
};
|
|
|
|
static struct i2c_adapter go7007_adap_templ = {
|
|
.owner = THIS_MODULE,
|
|
.name = "WIS GO7007SB",
|
|
.algo = &go7007_algo,
|
|
};
|
|
|
|
int go7007_i2c_init(struct go7007 *go)
|
|
{
|
|
memcpy(&go->i2c_adapter, &go7007_adap_templ,
|
|
sizeof(go7007_adap_templ));
|
|
go->i2c_adapter.dev.parent = go->dev;
|
|
i2c_set_adapdata(&go->i2c_adapter, go);
|
|
if (i2c_add_adapter(&go->i2c_adapter) < 0) {
|
|
dev_err(go->dev,
|
|
"go7007-i2c: error: i2c_add_adapter failed\n");
|
|
return -1;
|
|
}
|
|
return 0;
|
|
}
|