223 lines
6.9 KiB
Plaintext
223 lines
6.9 KiB
Plaintext
Regulator DT binding for MAX77620 Power management IC from Maxim Semiconductor.
|
|
|
|
Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The input supply
|
|
of these regulators are defined under parent device node.
|
|
Details of regulator properties are defined as child node under
|
|
sub-node "regulators" which is child node of device node.
|
|
|
|
Please refer file <Documentation/devicetree/bindings/regulator/regulator.txt>
|
|
for common regulator bindings used by client.
|
|
|
|
Following are properties of parent node related to regulators.
|
|
|
|
Optional properties:
|
|
-------------------
|
|
The input supply of regulators are the optional properties on the
|
|
parent device node. The input supply of these regulators are provided
|
|
through following properties:
|
|
in-sd0-supply: Input supply for SD0, INA-SD0 or INB-SD0 pins.
|
|
in-sd1-supply: Input supply for SD1.
|
|
in-sd2-supply: Input supply for SD2.
|
|
in-sd3-supply: Input supply for SD3.
|
|
in-ldo0-1-supply: Input supply for LDO0 and LDO1.
|
|
in-ldo2-supply: Input supply for LDO2.
|
|
in-ldo3-5-supply: Input supply for LDO3 and LDO5
|
|
in-ldo4-6-supply: Input supply for LDO4 and LDO6.
|
|
in-ldo7-8-supply: Input supply for LDO7 and LDO8.
|
|
|
|
Optional sub nodes for regulators under "regulators" subnode:
|
|
------------------------------------------------------------
|
|
The subnodes name is the name of regulator and it must be one of:
|
|
sd[0-3], ldo[0-8]
|
|
|
|
Each sub-node should contain the constraints and initialization
|
|
information for that regulator. The definition for each of these
|
|
nodes is defined using the standard binding for regulators found at
|
|
<Documentation/devicetree/bindings/regulator/regulator.txt>.
|
|
|
|
Theres are also additional properties for SD/LDOs. These additional properties
|
|
are required to configure FPS configuration parameters for SDs and LDOs.
|
|
Please refer <devicetree/bindings/mfd/max77620.txt> for more detail of Flexible
|
|
Power Sequence (FPS).
|
|
Following are additional properties:
|
|
|
|
- maxim,active-fps-source: FPS source for the regulators to get
|
|
enabled/disabled when system is in
|
|
active state. Valid values are:
|
|
- MAX77620_FPS_SRC_0,
|
|
FPS source is FPS0.
|
|
- MAX77620_FPS_SRC_1,
|
|
FPS source is FPS1
|
|
- MAX77620_FPS_SRC_2 and
|
|
FPS source is FPS2
|
|
- MAX77620_FPS_SRC_NONE.
|
|
Regulator is not controlled
|
|
by FPS events and it gets
|
|
enabled/disabled by register
|
|
access.
|
|
Absence of this property will leave
|
|
the FPS configuration register for that
|
|
regulator to default configuration.
|
|
|
|
- maxim,active-fps-power-up-slot: Sequencing event slot number on which
|
|
the regulator get enabled when
|
|
master FPS input event set to HIGH.
|
|
Valid values are 0 to 7.
|
|
This is applicable if FPS source is
|
|
selected as FPS0, FPS1 or FPS2.
|
|
|
|
- maxim,active-fps-power-down-slot: Sequencing event slot number on which
|
|
the regulator get disabled when master
|
|
FPS input event set to LOW.
|
|
Valid values are 0 to 7.
|
|
This is applicable if FPS source is
|
|
selected as FPS0, FPS1 or FPS2.
|
|
|
|
- maxim,suspend-fps-source: This is same as property
|
|
"maxim,active-fps-source" but value
|
|
get configured when system enters in
|
|
to suspend state.
|
|
|
|
- maxim,suspend-fps-power-up-slot: This is same as property
|
|
"maxim,active-fps-power-up-slot" but
|
|
this value get configured into FPS
|
|
configuration register when system
|
|
enters into suspend.
|
|
This is applicable if suspend state
|
|
FPS source is selected as FPS0, FPS1 or
|
|
|
|
- maxim,suspend-fps-power-down-slot: This is same as property
|
|
"maxim,active-fps-power-down-slot" but
|
|
this value get configured into FPS
|
|
configuration register when system
|
|
enters into suspend.
|
|
This is applicable if suspend state
|
|
FPS source is selected as FPS0, FPS1 or
|
|
FPS2.
|
|
- maxim,ramp-rate-setting: integer, ramp rate(uV/us) setting to be
|
|
configured to the device.
|
|
The platform may have different ramp
|
|
rate than advertised ramp rate if it has
|
|
design variation from Maxim's
|
|
recommended. On this case, platform
|
|
specific ramp rate is used for ramp time
|
|
calculation and this property is used
|
|
for device register configurations.
|
|
The measured ramp rate of platform is
|
|
provided by the regulator-ramp-delay
|
|
as described in <devicetree/bindings/
|
|
regulator/regulator.txt>.
|
|
Maxim Max77620 supports following ramp
|
|
delay:
|
|
SD: 13.75mV/us, 27.5mV/us, 55mV/us
|
|
LDOs: 5mV/us, 100mV/us
|
|
|
|
Note: If the measured ramp delay is same as advertised ramp delay then it is not
|
|
required to provide the ramp delay with property "maxim,ramp-rate-setting". The
|
|
ramp rate can be provided by the regulator-ramp-delay which will be used for
|
|
ramp time calculation for voltage change as well as for device configuration.
|
|
|
|
Example:
|
|
--------
|
|
#include <dt-bindings/mfd/max77620.h>
|
|
...
|
|
max77620@3c {
|
|
in-ldo0-1-supply = <&max77620_sd2>;
|
|
in-ldo7-8-supply = <&max77620_sd2>;
|
|
regulators {
|
|
sd0 {
|
|
regulator-name = "vdd-core";
|
|
regulator-min-microvolt = <600000>;
|
|
regulator-max-microvolt = <1400000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
|
|
};
|
|
|
|
sd1 {
|
|
regulator-name = "vddio-ddr";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
|
|
};
|
|
|
|
sd2 {
|
|
regulator-name = "vdd-pre-reg";
|
|
regulator-min-microvolt = <1350000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
};
|
|
|
|
sd3 {
|
|
regulator-name = "vdd-1v8";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
ldo0 {
|
|
regulator-name = "avdd-sys";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
ldo1 {
|
|
regulator-name = "vdd-pex";
|
|
regulator-min-microvolt = <1050000>;
|
|
regulator-max-microvolt = <1050000>;
|
|
};
|
|
|
|
ldo2 {
|
|
regulator-name = "vddio-sdmmc3";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
ldo3 {
|
|
regulator-name = "vdd-cam-hv";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
};
|
|
|
|
ldo4 {
|
|
regulator-name = "vdd-rtc";
|
|
regulator-min-microvolt = <1250000>;
|
|
regulator-max-microvolt = <1250000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
ldo5 {
|
|
regulator-name = "avdd-ts-hv";
|
|
regulator-min-microvolt = <3000000>;
|
|
regulator-max-microvolt = <3000000>;
|
|
};
|
|
|
|
ldo6 {
|
|
regulator-name = "vdd-ts";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
ldo7 {
|
|
regulator-name = "vdd-gen-pll-edp";
|
|
regulator-min-microvolt = <1050000>;
|
|
regulator-max-microvolt = <1050000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
ldo8 {
|
|
regulator-name = "vdd-hdmi-dp";
|
|
regulator-min-microvolt = <1050000>;
|
|
regulator-max-microvolt = <1050000>;
|
|
};
|
|
};
|
|
};
|