70 lines
2.8 KiB
Plaintext
70 lines
2.8 KiB
Plaintext
* Renesas Electronics SH EtherMAC
|
|
|
|
This file provides information on what the device node for the SH EtherMAC
|
|
interface contains.
|
|
|
|
Required properties:
|
|
- compatible: Must contain one or more of the following:
|
|
"renesas,gether-r8a7740" if the device is a part of R8A7740 SoC.
|
|
"renesas,ether-r8a7743" if the device is a part of R8A7743 SoC.
|
|
"renesas,ether-r8a7745" if the device is a part of R8A7745 SoC.
|
|
"renesas,ether-r8a7778" if the device is a part of R8A7778 SoC.
|
|
"renesas,ether-r8a7779" if the device is a part of R8A7779 SoC.
|
|
"renesas,ether-r8a7790" if the device is a part of R8A7790 SoC.
|
|
"renesas,ether-r8a7791" if the device is a part of R8A7791 SoC.
|
|
"renesas,ether-r8a7793" if the device is a part of R8A7793 SoC.
|
|
"renesas,ether-r8a7794" if the device is a part of R8A7794 SoC.
|
|
"renesas,ether-r7s72100" if the device is a part of R7S72100 SoC.
|
|
"renesas,rcar-gen1-ether" for a generic R-Car Gen1 device.
|
|
"renesas,rcar-gen2-ether" for a generic R-Car Gen2 or RZ/G1
|
|
device.
|
|
|
|
When compatible with the generic version, nodes must list
|
|
the SoC-specific version corresponding to the platform
|
|
first followed by the generic version.
|
|
|
|
- reg: offset and length of (1) the E-DMAC/feLic register block (required),
|
|
(2) the TSU register block (optional).
|
|
- interrupts: interrupt specifier for the sole interrupt.
|
|
- phy-mode: see ethernet.txt file in the same directory.
|
|
- phy-handle: see ethernet.txt file in the same directory.
|
|
- #address-cells: number of address cells for the MDIO bus, must be equal to 1.
|
|
- #size-cells: number of size cells on the MDIO bus, must be equal to 0.
|
|
- clocks: clock phandle and specifier pair.
|
|
- pinctrl-0: phandle, referring to a default pin configuration node.
|
|
|
|
Optional properties:
|
|
- interrupt-parent: the phandle for the interrupt controller that services
|
|
interrupts for this device.
|
|
- pinctrl-names: pin configuration state name ("default").
|
|
- renesas,no-ether-link: boolean, specify when a board does not provide a proper
|
|
Ether LINK signal.
|
|
- renesas,ether-link-active-low: boolean, specify when the Ether LINK signal is
|
|
active-low instead of normal active-high.
|
|
|
|
Example (Lager board):
|
|
|
|
ethernet@ee700000 {
|
|
compatible = "renesas,ether-r8a7790",
|
|
"renesas,rcar-gen2-ether";
|
|
reg = <0 0xee700000 0 0x400>;
|
|
interrupt-parent = <&gic>;
|
|
interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&mstp8_clks R8A7790_CLK_ETHER>;
|
|
phy-mode = "rmii";
|
|
phy-handle = <&phy1>;
|
|
pinctrl-0 = <ðer_pins>;
|
|
pinctrl-names = "default";
|
|
renesas,ether-link-active-low;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
phy1: ethernet-phy@1 {
|
|
reg = <1>;
|
|
interrupt-parent = <&irqc0>;
|
|
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
|
|
pinctrl-0 = <&phy1_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|