114 lines
4.3 KiB
Plaintext
114 lines
4.3 KiB
Plaintext
STMicroelectronics STM32 ADC device driver
|
|
|
|
STM32 ADC is a successive approximation analog-to-digital converter.
|
|
It has several multiplexed input channels. Conversions can be performed
|
|
in single, continuous, scan or discontinuous mode. Result of the ADC is
|
|
stored in a left-aligned or right-aligned 32-bit data register.
|
|
Conversions can be launched in software or using hardware triggers.
|
|
|
|
The analog watchdog feature allows the application to detect if the input
|
|
voltage goes beyond the user-defined, higher or lower thresholds.
|
|
|
|
Each STM32 ADC block can have up to 3 ADC instances.
|
|
|
|
Each instance supports two contexts to manage conversions, each one has its
|
|
own configurable sequence and trigger:
|
|
- regular conversion can be done in sequence, running in background
|
|
- injected conversions have higher priority, and so have the ability to
|
|
interrupt regular conversion sequence (either triggered in SW or HW).
|
|
Regular sequence is resumed, in case it has been interrupted.
|
|
|
|
Contents of a stm32 adc root node:
|
|
-----------------------------------
|
|
Required properties:
|
|
- compatible: Should be one of:
|
|
"st,stm32f4-adc-core"
|
|
"st,stm32h7-adc-core"
|
|
- reg: Offset and length of the ADC block register set.
|
|
- interrupts: Must contain the interrupt for ADC block.
|
|
- clocks: Core can use up to two clocks, depending on part used:
|
|
- "adc" clock: for the analog circuitry, common to all ADCs.
|
|
It's required on stm32f4.
|
|
It's optional on stm32h7.
|
|
- "bus" clock: for registers access, common to all ADCs.
|
|
It's not present on stm32f4.
|
|
It's required on stm32h7.
|
|
- clock-names: Must be "adc" and/or "bus" depending on part used.
|
|
- interrupt-controller: Identifies the controller node as interrupt-parent
|
|
- vref-supply: Phandle to the vref input analog reference voltage.
|
|
- #interrupt-cells = <1>;
|
|
- #address-cells = <1>;
|
|
- #size-cells = <0>;
|
|
|
|
Optional properties:
|
|
- A pinctrl state named "default" for each ADC channel may be defined to set
|
|
inX ADC pins in mode of operation for analog input on external pin.
|
|
|
|
Contents of a stm32 adc child node:
|
|
-----------------------------------
|
|
An ADC block node should contain at least one subnode, representing an
|
|
ADC instance available on the machine.
|
|
|
|
Required properties:
|
|
- compatible: Should be one of:
|
|
"st,stm32f4-adc"
|
|
"st,stm32h7-adc"
|
|
- reg: Offset of ADC instance in ADC block (e.g. may be 0x0, 0x100, 0x200).
|
|
- clocks: Input clock private to this ADC instance. It's required only on
|
|
stm32f4, that has per instance clock input for registers access.
|
|
- interrupt-parent: Phandle to the parent interrupt controller.
|
|
- interrupts: IRQ Line for the ADC (e.g. may be 0 for adc@0, 1 for adc@100 or
|
|
2 for adc@200).
|
|
- st,adc-channels: List of single-ended channels muxed for this ADC.
|
|
It can have up to 16 channels on stm32f4 or 20 channels on stm32h7, numbered
|
|
from 0 to 15 or 19 (resp. for in0..in15 or in0..in19).
|
|
- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in
|
|
Documentation/devicetree/bindings/iio/iio-bindings.txt
|
|
|
|
Optional properties:
|
|
- dmas: Phandle to dma channel for this ADC instance.
|
|
See ../../dma/dma.txt for details.
|
|
- dma-names: Must be "rx" when dmas property is being used.
|
|
- assigned-resolution-bits: Resolution (bits) to use for conversions. Must
|
|
match device available resolutions:
|
|
* can be 6, 8, 10 or 12 on stm32f4
|
|
* can be 8, 10, 12, 14 or 16 on stm32h7
|
|
Default is maximum resolution if unset.
|
|
- st,min-sample-time-nsecs: Minimum sampling time in nanoseconds.
|
|
Depending on hardware (board) e.g. high/low analog input source impedance,
|
|
fine tune of ADC sampling time may be recommended.
|
|
This can be either one value or an array that matches 'st,adc-channels' list,
|
|
to set sample time resp. for all channels, or independently for each channel.
|
|
|
|
Example:
|
|
adc: adc@40012000 {
|
|
compatible = "st,stm32f4-adc-core";
|
|
reg = <0x40012000 0x400>;
|
|
interrupts = <18>;
|
|
clocks = <&rcc 0 168>;
|
|
clock-names = "adc";
|
|
vref-supply = <®_vref>;
|
|
interrupt-controller;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&adc3_in8_pin>;
|
|
|
|
#interrupt-cells = <1>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
adc@0 {
|
|
compatible = "st,stm32f4-adc";
|
|
#io-channel-cells = <1>;
|
|
reg = <0x0>;
|
|
clocks = <&rcc 0 168>;
|
|
interrupt-parent = <&adc>;
|
|
interrupts = <0>;
|
|
st,adc-channels = <8>;
|
|
dmas = <&dma2 0 0 0x400 0x0>;
|
|
dma-names = "rx";
|
|
assigned-resolution-bits = <8>;
|
|
};
|
|
...
|
|
other adc child nodes follow...
|
|
};
|