148 lines
4.6 KiB
Plaintext
148 lines
4.6 KiB
Plaintext
Device-Tree bindings for LVDS Display Bridge (ldb)
|
|
|
|
LVDS Display Bridge
|
|
===================
|
|
|
|
The LVDS Display Bridge device tree node contains up to two lvds-channel
|
|
nodes describing each of the two LVDS encoder channels of the bridge.
|
|
|
|
Required properties:
|
|
- #address-cells : should be <1>
|
|
- #size-cells : should be <0>
|
|
- compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb".
|
|
Both LDB versions are similar, but i.MX6 has an additional
|
|
multiplexer in the front to select any of the four IPU display
|
|
interfaces as input for each LVDS channel.
|
|
- gpr : should be <&gpr> on i.MX53 and i.MX6q.
|
|
The phandle points to the iomuxc-gpr region containing the LVDS
|
|
control register.
|
|
- clocks, clock-names : phandles to the LDB divider and selector clocks and to
|
|
the display interface selector clocks, as described in
|
|
Documentation/devicetree/bindings/clock/clock-bindings.txt
|
|
The following clocks are expected on i.MX53:
|
|
"di0_pll" - LDB LVDS channel 0 mux
|
|
"di1_pll" - LDB LVDS channel 1 mux
|
|
"di0" - LDB LVDS channel 0 gate
|
|
"di1" - LDB LVDS channel 1 gate
|
|
"di0_sel" - IPU1 DI0 mux
|
|
"di1_sel" - IPU1 DI1 mux
|
|
On i.MX6q the following additional clocks are needed:
|
|
"di2_sel" - IPU2 DI0 mux
|
|
"di3_sel" - IPU2 DI1 mux
|
|
The needed clock numbers for each are documented in
|
|
Documentation/devicetree/bindings/clock/imx5-clock.txt, and in
|
|
Documentation/devicetree/bindings/clock/imx6q-clock.txt.
|
|
|
|
Optional properties:
|
|
- pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
|
|
- pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
|
|
not used on i.MX6q
|
|
- fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should
|
|
be configured - one input will be distributed on both outputs in dual
|
|
channel mode
|
|
|
|
LVDS Channel
|
|
============
|
|
|
|
Each LVDS Channel has to contain either an of graph link to a panel device node
|
|
or a display-timings node that describes the video timings for the connected
|
|
LVDS display as well as the fsl,data-mapping and fsl,data-width properties.
|
|
|
|
Required properties:
|
|
- reg : should be <0> or <1>
|
|
- port: Input and output port nodes with endpoint definitions as defined in
|
|
Documentation/devicetree/bindings/graph.txt.
|
|
On i.MX5, the internal two-input-multiplexer is used. Due to hardware
|
|
limitations, only one input port (port@[0,1]) can be used for each channel
|
|
(lvds-channel@[0,1], respectively).
|
|
On i.MX6, there should be four input ports (port@[0-3]) that correspond
|
|
to the four LVDS multiplexer inputs.
|
|
A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected
|
|
to a panel input port. Optionally, the output port can be left out if
|
|
display-timings are used instead.
|
|
|
|
Optional properties (required if display-timings are used):
|
|
- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
|
|
- display-timings : A node that describes the display timings as defined in
|
|
Documentation/devicetree/bindings/display/panel/display-timing.txt.
|
|
- fsl,data-mapping : should be "spwg" or "jeida"
|
|
This describes how the color bits are laid out in the
|
|
serialized LVDS signal.
|
|
- fsl,data-width : should be <18> or <24>
|
|
|
|
example:
|
|
|
|
gpr: iomuxc-gpr@53fa8000 {
|
|
/* ... */
|
|
};
|
|
|
|
ldb: ldb@53fa8008 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,imx53-ldb";
|
|
gpr = <&gpr>;
|
|
clocks = <&clks IMX5_CLK_LDB_DI0_SEL>,
|
|
<&clks IMX5_CLK_LDB_DI1_SEL>,
|
|
<&clks IMX5_CLK_IPU_DI0_SEL>,
|
|
<&clks IMX5_CLK_IPU_DI1_SEL>,
|
|
<&clks IMX5_CLK_LDB_DI0_GATE>,
|
|
<&clks IMX5_CLK_LDB_DI1_GATE>;
|
|
clock-names = "di0_pll", "di1_pll",
|
|
"di0_sel", "di1_sel",
|
|
"di0", "di1";
|
|
|
|
/* Using an of-graph endpoint link to connect the panel */
|
|
lvds-channel@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
|
|
lvds0_in: endpoint {
|
|
remote-endpoint = <&ipu_di0_lvds0>;
|
|
};
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
|
|
lvds0_out: endpoint {
|
|
remote-endpoint = <&panel_in>;
|
|
};
|
|
};
|
|
};
|
|
|
|
/* Using display-timings and fsl,data-mapping/width instead */
|
|
lvds-channel@1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <1>;
|
|
fsl,data-mapping = "spwg";
|
|
fsl,data-width = <24>;
|
|
|
|
display-timings {
|
|
/* ... */
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
|
|
lvds1_in: endpoint {
|
|
remote-endpoint = <&ipu_di1_lvds1>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
panel: lvds-panel {
|
|
/* ... */
|
|
|
|
port {
|
|
panel_in: endpoint {
|
|
remote-endpoint = <&lvds0_out>;
|
|
};
|
|
};
|
|
};
|