115 lines
3.5 KiB
Plaintext
115 lines
3.5 KiB
Plaintext
The Exynos display port interface should be configured based on
|
|
the type of panel connected to it.
|
|
|
|
We use two nodes:
|
|
-dp-controller node
|
|
-dptx-phy node(defined inside dp-controller node)
|
|
|
|
For the DP-PHY initialization, we use the dptx-phy node.
|
|
Required properties for dptx-phy: deprecated, use phys and phy-names
|
|
-reg: deprecated
|
|
Base address of DP PHY register.
|
|
-samsung,enable-mask: deprecated
|
|
The bit-mask used to enable/disable DP PHY.
|
|
|
|
For the Panel initialization, we read data from dp-controller node.
|
|
Required properties for dp-controller:
|
|
-compatible:
|
|
should be "samsung,exynos5-dp".
|
|
-reg:
|
|
physical base address of the controller and length
|
|
of memory mapped region.
|
|
-interrupts:
|
|
interrupt combiner values.
|
|
-clocks:
|
|
from common clock binding: handle to dp clock.
|
|
-clock-names:
|
|
from common clock binding: Shall be "dp".
|
|
-interrupt-parent:
|
|
phandle to Interrupt combiner node.
|
|
-phys:
|
|
from general PHY binding: the phandle for the PHY device.
|
|
-phy-names:
|
|
from general PHY binding: Should be "dp".
|
|
|
|
Optional properties for dp-controller:
|
|
-interlaced:
|
|
interlace scan mode.
|
|
Progressive if defined, Interlaced if not defined
|
|
-vsync-active-high:
|
|
VSYNC polarity configuration.
|
|
High if defined, Low if not defined
|
|
-hsync-active-high:
|
|
HSYNC polarity configuration.
|
|
High if defined, Low if not defined
|
|
-samsung,hpd-gpio:
|
|
Hotplug detect GPIO.
|
|
Indicates which GPIO should be used for hotplug
|
|
detection
|
|
-video interfaces: Device node can contain video interface port
|
|
nodes according to [1].
|
|
- display-timings: timings for the connected panel as described by
|
|
Documentation/devicetree/bindings/display/panel/display-timing.txt
|
|
|
|
For the below properties, please refer to Analogix DP binding document:
|
|
* Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
|
|
-phys (required)
|
|
-phy-names (required)
|
|
-hpd-gpios (optional)
|
|
force-hpd (optional)
|
|
|
|
Deprecated properties for DisplayPort:
|
|
-interlaced: deprecated prop that can parsed from drm_display_mode.
|
|
-vsync-active-high: deprecated prop that can parsed from drm_display_mode.
|
|
-hsync-active-high: deprecated prop that can parsed from drm_display_mode.
|
|
-samsung,ycbcr-coeff: deprecated prop that can parsed from drm_display_mode.
|
|
-samsung,dynamic-range: deprecated prop that can parsed from drm_display_mode.
|
|
-samsung,color-space: deprecated prop that can parsed from drm_display_info.
|
|
-samsung,color-depth: deprecated prop that can parsed from drm_display_info.
|
|
-samsung,link-rate: deprecated prop that can reading from monitor by dpcd method.
|
|
-samsung,lane-count: deprecated prop that can reading from monitor by dpcd method.
|
|
-samsung,hpd-gpio: deprecated name for hpd-gpios.
|
|
|
|
-------------------------------------------------------------------------------
|
|
|
|
Example:
|
|
|
|
SOC specific portion:
|
|
dp-controller {
|
|
compatible = "samsung,exynos5-dp";
|
|
reg = <0x145b0000 0x10000>;
|
|
interrupts = <10 3>;
|
|
interrupt-parent = <&combiner>;
|
|
clocks = <&clock 342>;
|
|
clock-names = "dp";
|
|
|
|
phys = <&dp_phy>;
|
|
phy-names = "dp";
|
|
};
|
|
|
|
Board Specific portion:
|
|
dp-controller {
|
|
display-timings {
|
|
native-mode = <&lcd_timing>;
|
|
lcd_timing: 1366x768 {
|
|
clock-frequency = <70589280>;
|
|
hactive = <1366>;
|
|
vactive = <768>;
|
|
hfront-porch = <40>;
|
|
hback-porch = <40>;
|
|
hsync-len = <32>;
|
|
vback-porch = <10>;
|
|
vfront-porch = <12>;
|
|
vsync-len = <6>;
|
|
};
|
|
};
|
|
|
|
ports {
|
|
port@0 {
|
|
dp_out: endpoint {
|
|
remote-endpoint = <&bridge_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|