79 lines
3.4 KiB
Plaintext
79 lines
3.4 KiB
Plaintext
NVIDIA Tegra124 DFLL FCPU clocksource
|
|
|
|
This binding uses the common clock binding:
|
|
Documentation/devicetree/bindings/clock/clock-bindings.txt
|
|
|
|
The DFLL IP block on Tegra is a root clocksource designed for clocking
|
|
the fast CPU cluster. It consists of a free-running voltage controlled
|
|
oscillator connected to the CPU voltage rail (VDD_CPU), and a closed loop
|
|
control module that will automatically adjust the VDD_CPU voltage by
|
|
communicating with an off-chip PMIC either via an I2C bus or via PWM signals.
|
|
Currently only the I2C mode is supported by these bindings.
|
|
|
|
Required properties:
|
|
- compatible : should be "nvidia,tegra124-dfll"
|
|
- reg : Defines the following set of registers, in the order listed:
|
|
- registers for the DFLL control logic.
|
|
- registers for the I2C output logic.
|
|
- registers for the integrated I2C master controller.
|
|
- look-up table RAM for voltage register values.
|
|
- interrupts: Should contain the DFLL block interrupt.
|
|
- clocks: Must contain an entry for each entry in clock-names.
|
|
See clock-bindings.txt for details.
|
|
- clock-names: Must include the following entries:
|
|
- soc: Clock source for the DFLL control logic.
|
|
- ref: The closed loop reference clock
|
|
- i2c: Clock source for the integrated I2C master.
|
|
- resets: Must contain an entry for each entry in reset-names.
|
|
See ../reset/reset.txt for details.
|
|
- reset-names: Must include the following entries:
|
|
- dvco: Reset control for the DFLL DVCO.
|
|
- #clock-cells: Must be 0.
|
|
- clock-output-names: Name of the clock output.
|
|
- vdd-cpu-supply: Regulator for the CPU voltage rail that the DFLL
|
|
hardware will start controlling. The regulator will be queried for
|
|
the I2C register, control values and supported voltages.
|
|
|
|
Required properties for the control loop parameters:
|
|
- nvidia,sample-rate: Sample rate of the DFLL control loop.
|
|
- nvidia,droop-ctrl: See the register CL_DVFS_DROOP_CTRL in the TRM.
|
|
- nvidia,force-mode: See the field DFLL_PARAMS_FORCE_MODE in the TRM.
|
|
- nvidia,cf: Numeric value, see the field DFLL_PARAMS_CF_PARAM in the TRM.
|
|
- nvidia,ci: Numeric value, see the field DFLL_PARAMS_CI_PARAM in the TRM.
|
|
- nvidia,cg: Numeric value, see the field DFLL_PARAMS_CG_PARAM in the TRM.
|
|
|
|
Optional properties for the control loop parameters:
|
|
- nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM.
|
|
|
|
Required properties for I2C mode:
|
|
- nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode.
|
|
|
|
Example:
|
|
|
|
clock@70110000 {
|
|
compatible = "nvidia,tegra124-dfll";
|
|
reg = <0 0x70110000 0 0x100>, /* DFLL control */
|
|
<0 0x70110000 0 0x100>, /* I2C output control */
|
|
<0 0x70110100 0 0x100>, /* Integrated I2C controller */
|
|
<0 0x70110200 0 0x100>; /* Look-up table RAM */
|
|
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&tegra_car TEGRA124_CLK_DFLL_SOC>,
|
|
<&tegra_car TEGRA124_CLK_DFLL_REF>,
|
|
<&tegra_car TEGRA124_CLK_I2C5>;
|
|
clock-names = "soc", "ref", "i2c";
|
|
resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>;
|
|
reset-names = "dvco";
|
|
#clock-cells = <0>;
|
|
clock-output-names = "dfllCPU_out";
|
|
vdd-cpu-supply = <&vdd_cpu>;
|
|
|
|
nvidia,sample-rate = <12500>;
|
|
nvidia,droop-ctrl = <0x00000f00>;
|
|
nvidia,force-mode = <1>;
|
|
nvidia,cf = <10>;
|
|
nvidia,ci = <0>;
|
|
nvidia,cg = <2>;
|
|
|
|
nvidia,i2c-fs-rate = <400000>;
|
|
};
|