224 lines
7.0 KiB
Plaintext
224 lines
7.0 KiB
Plaintext
Renesas RZ/A1 combined Pin and GPIO controller
|
|
|
|
The Renesas SoCs of the RZ/A1 family feature a combined Pin and GPIO controller,
|
|
named "Ports" in the hardware reference manual.
|
|
Pin multiplexing and GPIO configuration is performed on a per-pin basis
|
|
writing configuration values to per-port register sets.
|
|
Each "port" features up to 16 pins, each of them configurable for GPIO
|
|
function (port mode) or in alternate function mode.
|
|
Up to 8 different alternate function modes exist for each single pin.
|
|
|
|
Pin controller node
|
|
-------------------
|
|
|
|
Required properties:
|
|
- compatible: should be:
|
|
- "renesas,r7s72100-ports": for RZ/A1H
|
|
- "renesas,r7s72101-ports", "renesas,r7s72100-ports": for RZ/A1M
|
|
- "renesas,r7s72102-ports": for RZ/A1L
|
|
|
|
- reg
|
|
address base and length of the memory area where the pin controller
|
|
hardware is mapped to.
|
|
|
|
Example:
|
|
Pin controller node for RZ/A1H SoC (r7s72100)
|
|
|
|
pinctrl: pin-controller@fcfe3000 {
|
|
compatible = "renesas,r7s72100-ports";
|
|
|
|
reg = <0xfcfe3000 0x4230>;
|
|
};
|
|
|
|
Sub-nodes
|
|
---------
|
|
|
|
The child nodes of the pin controller node describe a pin multiplexing
|
|
function or a GPIO controller alternatively.
|
|
|
|
- Pin multiplexing sub-nodes:
|
|
A pin multiplexing sub-node describes how to configure a set of
|
|
(or a single) pin in some desired alternate function mode.
|
|
A single sub-node may define several pin configurations.
|
|
A few alternate function require special pin configuration flags to be
|
|
supplied along with the alternate function configuration number.
|
|
The hardware reference manual specifies when a pin function requires
|
|
"software IO driven" mode to be specified. To do so use the generic
|
|
properties from the <include/linux/pinctrl/pinconf_generic.h> header file
|
|
to instruct the pin controller to perform the desired pin configuration
|
|
operation.
|
|
Please refer to pinctrl-bindings.txt to get to know more on generic
|
|
pin properties usage.
|
|
|
|
The allowed generic formats for a pin multiplexing sub-node are the
|
|
following ones:
|
|
|
|
node-1 {
|
|
pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
|
|
GENERIC_PINCONFIG;
|
|
};
|
|
|
|
node-2 {
|
|
sub-node-1 {
|
|
pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
|
|
GENERIC_PINCONFIG;
|
|
};
|
|
|
|
sub-node-2 {
|
|
pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
|
|
GENERIC_PINCONFIG;
|
|
};
|
|
|
|
...
|
|
|
|
sub-node-n {
|
|
pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
|
|
GENERIC_PINCONFIG;
|
|
};
|
|
};
|
|
|
|
Use the second format when pins part of the same logical group need to have
|
|
different generic pin configuration flags applied.
|
|
|
|
Client sub-nodes shall refer to pin multiplexing sub-nodes using the phandle
|
|
of the most external one.
|
|
|
|
Eg.
|
|
|
|
client-1 {
|
|
...
|
|
pinctrl-0 = <&node-1>;
|
|
...
|
|
};
|
|
|
|
client-2 {
|
|
...
|
|
pinctrl-0 = <&node-2>;
|
|
...
|
|
};
|
|
|
|
Required properties:
|
|
- pinmux:
|
|
integer array representing pin number and pin multiplexing configuration.
|
|
When a pin has to be configured in alternate function mode, use this
|
|
property to identify the pin by its global index, and provide its
|
|
alternate function configuration number along with it.
|
|
When multiple pins are required to be configured as part of the same
|
|
alternate function they shall be specified as members of the same
|
|
argument list of a single "pinmux" property.
|
|
Helper macros to ease assembling the pin index from its position
|
|
(port where it sits on and pin number) and alternate function identifier
|
|
are provided by the pin controller header file at:
|
|
<include/dt-bindings/pinctrl/r7s72100-pinctrl.h>
|
|
Integers values in "pinmux" argument list are assembled as:
|
|
((PORT * 16 + PIN) | MUX_FUNC << 16)
|
|
|
|
Optional generic properties:
|
|
- input-enable:
|
|
enable input bufer for pins requiring software driven IO input
|
|
operations.
|
|
- output-high:
|
|
enable output buffer for pins requiring software driven IO output
|
|
operations. output-low can be used alternatively, as line value is
|
|
ignored by the driver.
|
|
|
|
The hardware reference manual specifies when a pin has to be configured to
|
|
work in bi-directional mode and when the IO direction has to be specified
|
|
by software. Bi-directional pins are managed by the pin controller driver
|
|
internally, while software driven IO direction has to be explicitly
|
|
selected when multiple options are available.
|
|
|
|
Example:
|
|
A serial communication interface with a TX output pin and an RX input pin.
|
|
|
|
&pinctrl {
|
|
scif2_pins: serial2 {
|
|
pinmux = <RZA1_PINMUX(3, 0, 6)>, <RZA1_PINMUX(3, 2, 4)>;
|
|
};
|
|
};
|
|
|
|
Pin #0 on port #3 is configured as alternate function #6.
|
|
Pin #2 on port #3 is configured as alternate function #4.
|
|
|
|
Example 2:
|
|
I2c master: both SDA and SCL pins need bi-directional operations
|
|
|
|
&pinctrl {
|
|
i2c2_pins: i2c2 {
|
|
pinmux = <RZA1_PINMUX(1, 4, 1)>, <RZA1_PINMUX(1, 5, 1)>;
|
|
};
|
|
};
|
|
|
|
Pin #4 on port #1 is configured as alternate function #1.
|
|
Pin #5 on port #1 is configured as alternate function #1.
|
|
Both need to work in bi-directional mode, the driver manages this internally.
|
|
|
|
Example 3:
|
|
Multi-function timer input and output compare pins.
|
|
Configure TIOC0A as software driven input and TIOC0B as software driven
|
|
output.
|
|
|
|
&pinctrl {
|
|
tioc0_pins: tioc0 {
|
|
tioc0_input_pins {
|
|
pinumx = <RZA1_PINMUX(4, 0, 2)>;
|
|
input-enable;
|
|
};
|
|
|
|
tioc0_output_pins {
|
|
pinmux = <RZA1_PINMUX(4, 1, 1)>;
|
|
output-enable;
|
|
};
|
|
};
|
|
};
|
|
|
|
&tioc0 {
|
|
...
|
|
pinctrl-0 = <&tioc0_pins>;
|
|
...
|
|
};
|
|
|
|
Pin #0 on port #4 is configured as alternate function #2 with IO direction
|
|
specified by software as input.
|
|
Pin #1 on port #4 is configured as alternate function #1 with IO direction
|
|
specified by software as output.
|
|
|
|
- GPIO controller sub-nodes:
|
|
Each port of the r7s72100 pin controller hardware is itself a GPIO controller.
|
|
Different SoCs have different numbers of available pins per port, but
|
|
generally speaking, each of them can be configured in GPIO ("port") mode
|
|
on this hardware.
|
|
Describe GPIO controllers using sub-nodes with the following properties.
|
|
|
|
Required properties:
|
|
- gpio-controller
|
|
empty property as defined by the GPIO bindings documentation.
|
|
- #gpio-cells
|
|
number of cells required to identify and configure a GPIO.
|
|
Shall be 2.
|
|
- gpio-ranges
|
|
Describes a GPIO controller specifying its specific pin base, the pin
|
|
base in the global pin numbering space, and the number of controlled
|
|
pins, as defined by the GPIO bindings documentation. Refer to
|
|
Documentation/devicetree/bindings/gpio/gpio.txt file for a more detailed
|
|
description.
|
|
|
|
Example:
|
|
A GPIO controller node, controlling 16 pins indexed from 0.
|
|
The GPIO controller base in the global pin indexing space is pin 48, thus
|
|
pins [0 - 15] on this controller map to pins [48 - 63] in the global pin
|
|
indexing space.
|
|
|
|
port3: gpio-3 {
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
gpio-ranges = <&pinctrl 0 48 16>;
|
|
};
|
|
|
|
A device node willing to use pins controlled by this GPIO controller, shall
|
|
refer to it as follows:
|
|
|
|
led1 {
|
|
gpios = <&port3 10 GPIO_ACTIVE_LOW>;
|
|
};
|